- Home
- Modbus register maps
- Camille Bauer Metrawatt
- SINEAX CAM universal measurement device (Modbus/TCP)
Power meter (universal measuring / power quality device) · Modbus register map
Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) Modbus register map
Updated 17 November 2026
The SINEAX CAM is a Swiss universal measurement device for heavy-current networks with plug-in I/O modules. With the Modbus/TCP bus card it publishes its measurements as holding registers (mostly IEEE 754 floats), relay and digital output states as coils and digital inputs as discrete inputs. This map covers firmware info, the full instantaneous value block, THD/TDD, symmetrical components, analog inputs and the I/O states.
This page lists 108 Modbus registers for the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) — 16 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Camille Bauer Metrawatt’s own free documentation (linked below) and checked against it.
- Manufacturer
- Camille Bauer Metrawatt
- Model
- SINEAX CAM universal measurement device (Modbus/TCP)
- Equipment type
- Power meter (universal measuring / power quality device)
- Registers
- 108 (16 writable)
- Transport
- Modbus TCP
- Default unit ID
- Not stated
- TCP port
- 502
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- CDAB low word first (word-swapped)
- Firmware
- Analysis firmware 1.32+ (timestamp), 1.37+ (system analysis block), 1.39+ (tariff register 41485)
- Also known as
- SINEAX CAM, CAM
Integration notes: Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP)
Connect to TCP port 502 and read 40100-40187 in one FC3 request: 44 floats with voltage, current, power, frequency and power factor, low word first. THD/TDD sit in 40190-40196 as tenths of a percent.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 101 | U1N | FLOAT32 CDAB | Voltage L1-N | Read |
| HR 117 | I1 | FLOAT32 CDAB | Current L1 | Read |
| HR 133 | P | FLOAT32 CDAB | Active power system | Read |
| HR 157 | F | FLOAT32 CDAB | Frequency | Read |
| HR 159 | PF | FLOAT32 CDAB | Power factor system | Read |
| HR 190 | THD_U1X | UINT16 | Voltage THD phase 1 | Read |
Enable Modbus control & writes
Assign IP address, mask and gateway with the CB-Manager software (factory IP 192.168.1.101). The Modbus/TCP port can be changed there, but 502 is always supported.
Byte order & addressing
- Floats are low word first (CDAB).
- Use FC 0x10 / 0x0F for writes; single-write function codes are not implemented.
- The manual's TCP examples use unit ID 0xFF since the IP address selects the device.
Network setup
- At least 5 simultaneous Modbus/TCP clients are supported.
- Up to two NTP servers can be set in CB-Manager for clock synchronisation (port 123).
Watch out for
- Several blocks only exist from a given analysis firmware version (1.32, 1.37, 1.39); read FV_OUTPUT at 40007 first.
- Register 40016 (CFG_DIGIO) is writable and changes module I/O direction; do not write it by accident.
Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| CO | 0doc 1 | RELAY1 state | BIT | Read/write | |||||
| CO | 1doc 2 | RELAY2 state | BIT | Read/write | |||||
| CO | 2doc 3 | DIGOUT1.1 state | Digital output on I/O module 1. | BIT | Read/write | ||||
| CO | 3doc 4 | DIGOUT1.2 state | Digital output on I/O module 1. | BIT | Read/write | ||||
| CO | 4doc 5 | DIGOUT1.3 state | Digital output on I/O module 1. | BIT | Read/write | ||||
| CO | 5doc 6 | DIGOUT2.1 state | Digital output on I/O module 2. | BIT | Read/write | ||||
| CO | 6doc 7 | DIGOUT2.2 state | Digital output on I/O module 2. | BIT | Read/write | ||||
| CO | 7doc 8 | DIGOUT2.3 state | Digital output on I/O module 2. | BIT | Read/write | ||||
| CO | 8doc 9 | DIGOUT3.1 state | Digital output on I/O module 3. | BIT | Read/write | ||||
| CO | 9doc 10 | DIGOUT3.2 state | Digital output on I/O module 3. | BIT | Read/write | ||||
| CO | 10doc 11 | DIGOUT3.3 state | Digital output on I/O module 3. | BIT | Read/write | ||||
| CO | 11doc 12 | DIGOUT4.1 state | Digital output on I/O module 4. | BIT | Read/write | ||||
| CO | 12doc 13 | DIGOUT4.2 state | Digital output on I/O module 4. | BIT | Read/write | ||||
| CO | 13doc 14 | DIGOUT4.3 state | Digital output on I/O module 4. | BIT | Read/write | ||||
| CO | 499doc 500 | Reset maximum value U | Coils 500-541 reset each min/max value with its timestamp. | BIT | Write | ||||
| CO | 1024doc 1025 | CNT_TARIF - tariff switch | BIT | Read/write | 0 = High tariff; 1 = Low tariff | ||||
| DI | 2doc 10003 | DIGIN1.1 state | Digital input on I/O module 1. | BIT | Read | ||||
| DI | 3doc 10004 | DIGIN1.2 state | Digital input on I/O module 1. | BIT | Read | ||||
| DI | 4doc 10005 | DIGIN1.3 state | Digital input on I/O module 1. | BIT | Read | ||||
| DI | 5doc 10006 | DIGIN2.1 state | Digital input on I/O module 2. | BIT | Read | ||||
| DI | 6doc 10007 | DIGIN2.2 state | Digital input on I/O module 2. | BIT | Read | ||||
| DI | 7doc 10008 | DIGIN2.3 state | Digital input on I/O module 2. | BIT | Read | ||||
| DI | 8doc 10009 | DIGIN3.1 state | Digital input on I/O module 3. | BIT | Read | ||||
| DI | 9doc 10010 | DIGIN3.2 state | Digital input on I/O module 3. | BIT | Read | ||||
| DI | 10doc 10011 | DIGIN3.3 state | Digital input on I/O module 3. | BIT | Read | ||||
| DI | 11doc 10012 | DIGIN4.1 state | Digital input on I/O module 4. | BIT | Read | ||||
| DI | 12doc 10013 | DIGIN4.2 state | Digital input on I/O module 4. | BIT | Read | ||||
| DI | 13doc 10014 | DIGIN4.3 state | Digital input on I/O module 4. | BIT | Read | ||||
| HR | 5doc 40006 | FV_INPUT - firmware measurement part | Hex coded, e.g. 0x0106 = 1.06. | UINT16 | Read | ||||
| HR | 6doc 40007 | FV_OUTPUT - firmware analysis unit | Hex coded, e.g. 0x0137 = 1.37. Several blocks need a minimum version. | UINT16 | Read | ||||
| HR | 7doc 40008 | FV_COM - firmware communication unit | Hex coded. | UINT16 | Read | ||||
| HR | 14doc 40015 | HW_FREQ - calibration frequency | 5000 = 50.00 Hz. | UINT16 | × 0.01 | Hz | Read | ||
| HR | 99doc 40100 | U | System voltage | FLOAT32 | CDAB | V | Read | ||
| HR | 101doc 40102 | U1N | Voltage L1-N | FLOAT32 | CDAB | V | Read | ||
| HR | 103doc 40104 | U2N | Voltage L2-N | FLOAT32 | CDAB | V | Read | ||
| HR | 105doc 40106 | U3N | Voltage L3-N | FLOAT32 | CDAB | V | Read | ||
| HR | 107doc 40108 | U12 | Voltage L1-L2 | FLOAT32 | CDAB | V | Read | ||
| HR | 109doc 40110 | U23 | Voltage L2-L3 | FLOAT32 | CDAB | V | Read | ||
| HR | 111doc 40112 | U31 | Voltage L3-L1 | FLOAT32 | CDAB | V | Read | ||
| HR | 113doc 40114 | UNE | Zero displacement voltage (4-wire) | FLOAT32 | CDAB | V | Read | ||
| HR | 115doc 40116 | I | System current | FLOAT32 | CDAB | A | Read | ||
| HR | 117doc 40118 | I1 | Current L1 | FLOAT32 | CDAB | A | Read | ||
| HR | 119doc 40120 | I2 | Current L2 | FLOAT32 | CDAB | A | Read | ||
| HR | 121doc 40122 | I3 | Current L3 | FLOAT32 | CDAB | A | Read | ||
| HR | 123doc 40124 | IN | Neutral current | FLOAT32 | CDAB | A | Read | ||
| HR | 125doc 40126 | IB | Bimetal current (balanced systems) | FLOAT32 | CDAB | A | Read | ||
| HR | 127doc 40128 | IB1 | Bimetal current L1 | FLOAT32 | CDAB | A | Read | ||
| HR | 129doc 40130 | IB2 | Bimetal current L2 | FLOAT32 | CDAB | A | Read | ||
| HR | 131doc 40132 | IB3 | Bimetal current L3 | FLOAT32 | CDAB | A | Read | ||
| HR | 133doc 40134 | P | Active power system (P1+P2+P3) | FLOAT32 | CDAB | Read | |||
| HR | 135doc 40136 | P1 | Active power L1 | FLOAT32 | CDAB | Read | |||
| HR | 137doc 40138 | P2 | Active power L2 | FLOAT32 | CDAB | Read | |||
| HR | 139doc 40140 | P3 | Active power L3 | FLOAT32 | CDAB | Read | |||
| HR | 141doc 40142 | Q | Reactive power system | FLOAT32 | CDAB | Read | |||
| HR | 143doc 40144 | Q1 | Reactive power L1 | FLOAT32 | CDAB | Read | |||
| HR | 145doc 40146 | Q2 | Reactive power L2 | FLOAT32 | CDAB | Read | |||
| HR | 147doc 40148 | Q3 | Reactive power L3 | FLOAT32 | CDAB | Read | |||
| HR | 149doc 40150 | S | Apparent power system | FLOAT32 | CDAB | Read | |||
| HR | 151doc 40152 | S1 | Apparent power L1 | FLOAT32 | CDAB | Read | |||
| HR | 153doc 40154 | S2 | Apparent power L2 | FLOAT32 | CDAB | Read | |||
| HR | 155doc 40156 | S3 | Apparent power L3 | FLOAT32 | CDAB | Read | |||
| HR | 157doc 40158 | F | System frequency | FLOAT32 | CDAB | Hz | Read | ||
| HR | 159doc 40160 | PF | Active power factor system (P/S) | FLOAT32 | CDAB | Read | |||
| HR | 161doc 40162 | PF1 | Power factor L1 | FLOAT32 | CDAB | Read | |||
| HR | 163doc 40164 | PF2 | Power factor L2 | FLOAT32 | CDAB | Read | |||
| HR | 165doc 40166 | PF3 | Power factor L3 | FLOAT32 | CDAB | Read | |||
| HR | 167doc 40168 | QF | Reactive power factor system (Q/S) | FLOAT32 | CDAB | Read | |||
| HR | 169doc 40170 | QF1 | Reactive power factor L1 | FLOAT32 | CDAB | Read | |||
| HR | 171doc 40172 | QF2 | Reactive power factor L2 | FLOAT32 | CDAB | Read | |||
| HR | 173doc 40174 | QF3 | Reactive power factor L3 | FLOAT32 | CDAB | Read | |||
| HR | 175doc 40176 | LF | Load factor system | FLOAT32 | CDAB | Read | |||
| HR | 177doc 40178 | LF1 | Load factor L1 | FLOAT32 | CDAB | Read | |||
| HR | 179doc 40180 | LF2 | Load factor L2 | FLOAT32 | CDAB | Read | |||
| HR | 181doc 40182 | LF3 | Load factor L3 | FLOAT32 | CDAB | Read | |||
| HR | 183doc 40184 | U_MEAN | Average of U1N, U2N, U3N | FLOAT32 | CDAB | V | Read | ||
| HR | 185doc 40186 | I_MEAN | Average of I1, I2, I3 | FLOAT32 | CDAB | A | Read | ||
| HR | 189doc 40190 | UNB_U | Voltage unbalance factor (4-wire); 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 190doc 40191 | THD_U1X | Voltage THD phase 1; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 191doc 40192 | THD_U2X | Voltage THD phase 2; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 192doc 40193 | THD_U3X | Voltage THD phase 3; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 193doc 40194 | TDD_I1 | Current TDD phase 1; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 194doc 40195 | TDD_I2 | Current TDD phase 2; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 195doc 40196 | TDD_I3 | Current TDD phase 3; 1000 = 100 %. | UINT16 | × 0.1 | % | Read | ||
| HR | 989doc 40990 | UR1 | Voltage positive sequence (FW 1.37+) | FLOAT32 | CDAB | V | Read | ||
| HR | 991doc 40992 | UR2 | Voltage negative sequence | FLOAT32 | CDAB | V | Read | ||
| HR | 993doc 40994 | U0 | Voltage zero sequence | FLOAT32 | CDAB | V | Read | ||
| HR | 995doc 40996 | IR1 | Current positive sequence | FLOAT32 | CDAB | A | Read | ||
| HR | 997doc 40998 | IR2 | Current negative sequence | FLOAT32 | CDAB | A | Read | ||
| HR | 999doc 41000 | I0 | Current zero sequence | FLOAT32 | CDAB | A | Read | ||
| HR | 1001doc 41002 | UNB_UR2_UR1 | Voltage unbalance UR2/UR1 | FLOAT32 | CDAB | % | Read | ||
| HR | 1003doc 41004 | UNB_IR2_IR1 | Current unbalance IR2/IR1 | FLOAT32 | CDAB | % | Read | ||
| HR | 1005doc 41006 | UNB_U0_UR1 | Voltage unbalance U0/UR1 | FLOAT32 | CDAB | % | Read | ||
| HR | 1007doc 41008 | UNB_I0_IR1 | Current unbalance I0/IR1 | FLOAT32 | CDAB | % | Read | ||
| HR | 1009doc 41010 | THD_U1X (float) | Voltage THD phase 1 | FLOAT32 | CDAB | Read | |||
| HR | 1011doc 41012 | THD_U2X (float) | Voltage THD phase 2 | FLOAT32 | CDAB | Read | |||
| HR | 1013doc 41014 | THD_U3X (float) | Voltage THD phase 3 | FLOAT32 | CDAB | Read | |||
| HR | 1015doc 41016 | TDD_I1 (float) | Current TDD phase 1 | FLOAT32 | CDAB | Read | |||
| HR | 1017doc 41018 | TDD_I2 (float) | Current TDD phase 2 | FLOAT32 | CDAB | Read | |||
| HR | 1019doc 41020 | TDD_I3 (float) | Current TDD phase 3 | FLOAT32 | CDAB | Read | |||
| HR | 1329doc 41330 | AIN1.1 analog input value | Value of analog input module 1 channel 1 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1331doc 41332 | AIN1.2 analog input value | Value of analog input module 1 channel 2 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1333doc 41334 | AIN2.1 analog input value | Value of analog input module 2 channel 1 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1335doc 41336 | AIN2.2 analog input value | Value of analog input module 2 channel 2 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1337doc 41338 | AIN3.1 analog input value | Value of analog input module 3 channel 1 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1339doc 41340 | AIN3.2 analog input value | Value of analog input module 3 channel 2 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1341doc 41342 | AIN4.1 analog input value | Value of analog input module 4 channel 1 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1343doc 41344 | AIN4.2 analog input value | Value of analog input module 4 channel 2 (unit as configured). | FLOAT32 | CDAB | Read | |||
| HR | 1484doc 41485 | CNTR_TARIF - tariff in use | Firmware 1.39 and later. | UINT16 | Read | 0 = High tariff; 1 = Low tariff |
Notes on this map
- Host: this copy is hosted on api-usa.com, not on a Camille Bauer site; no public copy was found on camillebauer.com.
- Float word order: the manual says the first register holds bits 0-15 and the second bits 16-31, and its U1N example reads 0xE878 then 0x436B (= 234.908 V). That is low word first, CDAB.
- Power units: the manual does not print units for P, Q, S (only V and A are given, in the system-analysis table and the U1N example), so units are left blank here; check against the device display.
- Left out: every UINT32 / TIME value (energy meters 41400-41482, logic-function words 43917-43923, timestamps 40096-40098 and min/max times), because the document gives no word order for 32-bit integers. Energy meters also need a scaling exponent whose register is not listed for the standard meters.
- Left out: min/max floats 40584-40666, harmonics 40200-40493 (UINT16 x 0.1 %, same scale as THD), mean values 41030-41322 (meaning depends on configuration) and parameter blocks.
- Availability depends on the connection type (single phase, split phase, 3-wire, 4-wire); registers that do not apply read 0.
- Function codes 0x05 and 0x06 (single coil/register write) and 0x04 (input registers) are not implemented; use 0x0F and 0x10.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP)
What Modbus registers does the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) have?
This map lists 108 registers: 16 coils, 12 discrete inputs, 80 holding registers. 16 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed 4xxxx and coils/inputs 0xxxx/1xxxx. The manual's own example: U1N at 40102 is sent as address 101 (0x65). Coil 1 is address 0, discrete input 10003 is address 2.
What byte order does the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP)?
Start with HR 101 U1N (Voltage L1-N); HR 117 I1 (Current L1); HR 133 P (Active power system); HR 157 F (Frequency); HR 159 PF (Power factor system); HR 190 THD_U1X (Voltage THD phase 1).
How do I enable Modbus control of the Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP)?
Assign IP address, mask and gateway with the CB-Manager software (factory IP 192.168.1.101). The Modbus/TCP port can be changed there, but 502 is always supported.
Where is the official Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP) Modbus documentation?
The source is Modbus/TCP interface SINEAX CAM (W 157471 (modification 2014-018, 18.06.14)), revision 2014-06-18. Camille Bauer Metrawatt doesn't publish it on its own website, so this map was re-typed from a free copy at https://api-usa.com/pdf/cb/Modbus_TCP_Interface_CAM.pdf. It may be an older revision, so check it against the live unit.
Other power & energy meters register maps
- Energy meter
Carlo Gavazzi EM24-IS (SFA and SFB models)
EM24-DIN AV2/AV5 IS SFA and SFB versions (identification codes 1696-1699), protocol revision 2.0.
Also known as: EM24DINAV23XISSFA, EM24DINAV53XISSFA, EM24DINAV23XISSFB, EM24DINAV53XISSFB, EM24 SFA, EM24 SFB - Power meter (power analyzer)
Carlo Gavazzi WM14 Advanced / CPT-DIN Advanced power analyzer (legacy)
WM14 Advanced (revision 5 onward) and CPT-DIN Advanced (revision 6 onward) with RS485 (or RS232 on CPT-DIN), protocol version 2 revision 2 (2008-01-09).
Also known as: WM14-96 Advanced, WM14 A, CPT-DIN Advanced, CPT A, CPT-DIN A - Power meter
Circutor CVM-C5
Circutor CVM-C5 panel power analyzer, RS-485 Modbus RTU versions (ITF-485, MC-485, mV-485), manual M026B01-03.
Also known as: CVM-C5-ITF-485, CVM-C5-MC-485, CVM-C5-mV-485 - Power meter (power quality analyzer)
E-Mon (Honeywell) PowerSmart+ Advanced power quality meter
Honeywell E-Mon PowerSmart+ Advanced power quality meter, per Modbus reference guide BG0545 Rev. A1 (Jul 2013).
Also known as: E-Mon PowerSmart+ Advanced, PowerSmart Plus Advanced, Honeywell PowerSmart+, BG0545 - Energy meter
Eastron SDM630-Modbus
Eastron SDM630Modbus three-phase DIN-rail meter, protocol implementation V1.8 as published by Eastron Europe.
Also known as: SDM630Modbus, SDM630 Modbus V2, SDM630-Modbus V2 - Sensor (ultrasonic gas flowmeter)
Endress+Hauser Proline Prosonic Flow G 300 ultrasonic gas flowmeter (Modbus RS485)
Prosonic Flow G 300 with the Modbus RS485 communication option, parameter description GP01131D/06/EN/02.24-00.
Also known as: Prosonic Flow G 300
All power & energy meters Modbus register maps →
Source: Modbus/TCP interface SINEAX CAM · W 157471 (modification 2014-018, 18.06.14) · rev. 2014-06-18 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.