- Home
- Modbus register maps
- Eltako
- DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)
Energy meter · Modbus register map
Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) Modbus register map
Updated 17 November 2026
The DSZ15DZMOD is Eltako's MID-approved bidirectional three-phase energy meter for direct connection up to 80 A, with an RS485 Modbus RTU interface. Values are 32-bit integers sent high word first: voltages, currents, power factors and import/export energy (total and partial) with fixed decimals.
This page lists 19 Modbus registers for the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) — 1 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Eltako’s own free documentation (linked below) and checked against it.
- Manufacturer
- Eltako
- Model
- DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)
- Equipment type
- Energy meter
- Registers
- 19 (1 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Default serial
- 9600 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- DSZ15DZMOD, DSZ15DZMOD-3x80A, DSZ15DZMOD-3x80A MID, 28380516
Integration notes: Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)
Read input registers (function 04) at 0x0000-0x0063 for voltages, currents, power factors and energy; each value is 2 registers, high word first. Total import energy is at 0x0048 in 0.01 kWh.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 72 | Total import active energy | UINT32 ABCD | Total import active energy (0.01 kWh) | Read |
| IR 74 | Total export active energy | UINT32 ABCD | Total export active energy | Read |
| IR 0 | Voltage L1-N | UINT32 ABCD | Voltage L1-N | Read |
| IR 6 | Current L1 | UINT32 ABCD | Current L1 | Read |
| IR 62 | Total power factor | INT32 ABCD | Total power factor | Read |
Enable Modbus control & writes
The spec does not describe enabling Modbus. Change the Modbus address by writing register 0x0014 with function 16 (the spec's example sets 0x2A).
Byte order & addressing
- Hex start addresses are wire addresses.
- Power-factor registers are signed with 3 decimals; other values unsigned with 2 decimals.
Network setup
- 9600 baud, 8 data bits, no parity, 1 stop bit.
- Address range 1-250.
Watch out for
- There is no published power resolution; use energy deltas if you need power.
- Partial energy registers are separate from the totals; do not mix them up.
Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 (0x0000) | Voltage L1-N | UINT32 | ABCD | × 0.01 | V | Read | ||
| IR | 2doc 30003 (0x0002) | Voltage L2-N | UINT32 | ABCD | × 0.01 | V | Read | ||
| IR | 4doc 30005 (0x0004) | Voltage L3-N | UINT32 | ABCD | × 0.01 | V | Read | ||
| IR | 6doc 30007 (0x0006) | Current L1 | UINT32 | ABCD | × 0.01 | A | Read | ||
| IR | 8doc 30009 (0x0008) | Current L2 | UINT32 | ABCD | × 0.01 | A | Read | ||
| IR | 10doc 30011 (0x000A) | Current L3 | UINT32 | ABCD | × 0.01 | A | Read | ||
| IR | 30doc 30031 (0x001E) | Power factor L1 | Signed, 3 decimals. | INT32 | ABCD | × 0.001 | Read | ||
| IR | 32doc 30033 (0x0020) | Power factor L2 | Signed, 3 decimals. | INT32 | ABCD | × 0.001 | Read | ||
| IR | 34doc 30035 (0x0022) | Power factor L3 | Signed, 3 decimals. | INT32 | ABCD | × 0.001 | Read | ||
| IR | 62doc 30063 (0x003E) | Total power factor | Signed, 3 decimals. | INT32 | ABCD | × 0.001 | Read | ||
| IR | 72doc 30073 (0x0048) | Total import active energy | The manual's example reads 0x000001CD = 4.61 kWh here. | UINT32 | ABCD | × 0.01 | kWh | Read | |
| IR | 74doc 30075 (0x004A) | Total export active energy | UINT32 | ABCD | × 0.01 | kWh | Read | ||
| IR | 96doc 30097 (0x0060) | Partial import active energy | UINT32 | ABCD | × 0.01 | kWh | Read | ||
| IR | 98doc 30099 (0x0062) | Partial export active energy | UINT32 | ABCD | × 0.01 | kWh | Read | ||
| HR | 18doc 40019 (0x0012) | Parity / stop bits | INT32 | ABCD | Read | 0 = 1 stop bit, no parity | |||
| HR | 20doc 40021 (0x0014) | Modbus address | 1-250; the manual's example writes 0x2A with function 16. | INT32 | ABCD | Read/write | |||
| HR | 28doc 40029 (0x001C) | Baud rate | Default 2 (9600). | INT32 | ABCD | Read | 0 = 2400; 1 = 4800; 2 = 9600; 3 = 19200; 5 = 1200 | ||
| HR | 86doc 40087 (0x0056) | Pulse output mode | Default 2; read with function 03 in the manual's example. | INT32 | ABCD | Read | |||
| HR | 64514doc 464515 (0xFC02) | Meter code | Fixed code; the table shows 0x0000000D. | INT32 | ABCD | Read |
Notes on this map
- Word order: the spec says multi-register data runs from the lower to the higher register address with each register high byte first, and its energy example answers 00 00 01 CD 00 00 01 70 for 4.61 kWh import and 3.68 kWh export, so 32-bit values are ABCD.
- Scaling (remark 1): all values except power and power factor are unsigned with 2 decimals; power factor is signed with 3 decimals.
- Left out: L1/L2/L3 and total active power (0x000C-0x0010, 0x0034). The remark says power is signed 'without decimal' while the unit column says kW, which would mean whole kilowatts; the resolution is too unclear to publish.
- Left out: the serial number at 0xFC00 (BCD).
- Measured values are read with function 04, parameters with function 03 and written with function 16. The spec's examples also use slave address 00 in place of the meter address.
- The parameter table marks the baud-rate and stop-bit rows read only; only the Modbus address is listed as read/write.
- The parameter rows are typed only as 'int' with no sign stated; they are listed as INT32, and all documented values are small positive numbers.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)
What Modbus registers does the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) have?
This map lists 19 registers: 14 input registers, 5 holding registers. 1 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Each row gives a 3xxxx/4xxxx reference and a hex start address; the hex value is the wire address (30073 = 0x0048). The manual's example frame CC 04 00 48 00 04 reads total import and export energy at 0x0048.
What byte order does the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)?
Start with IR 72 Total import active energy (Total import active energy (0.01 kWh)); IR 74 Total export active energy (Total export active energy); IR 0 Voltage L1-N (Voltage L1-N); IR 6 Current L1 (Current L1); IR 62 Total power factor (Total power factor).
How do I enable Modbus control of the Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU)?
The spec does not describe enabling Modbus. Change the Modbus address by writing register 0x0014 with function 16 (the spec's example sets 0x2A).
Where is the official Eltako DSZ15DZMOD-3x80A MID three-phase energy meter (Modbus RTU) Modbus documentation?
The source is Modbus-RTU protocol specification for DSZ15DZMOD V1.6 (English version) (V1.6), revision 2023-06, published free by Eltako at https://www.eltako.com/fileadmin/downloads/de/_bedienung/Modbus-RTU_protocol_specification_for_DSZ15DZMOD_V1.6_English_version.pdf.
Other power & energy meters register maps
- Energy meter
Finder 7M.38 three-phase energy meter (Modbus RS485)
Finder 7M.38 three-phase meters with serial RS485 communication (7M.38.8.400.XXXX serial versions); the 7M.24 single-phase meter in the same document is not covered.
Also known as: 7M.38, 7M38, 7M.38.8.400.0212, 7M3884000212, Finder 7M38 Modbus - Power meter
IME Nemo 96HDe multifunction meter (MF96E06)
IME Nemo 96HDe panel meter MF96E06 with RS-485, per protocol PR145.
Also known as: MF96E06, Nemo 96HDe - Energy meter
inepro Metering PRO1-Mod single-phase energy meter (PRO1 series, manual V3.02)
PRO1-Mod of the PRO1 series (PRO1-S/-2T/-Mb/-Mod), register map of user manual version 302 (2025).
Also known as: PRO1-Mod, PRO1 Mod, PRO1 MID, inepro PRO1 legacy - Power meter (power analyser)
Janitza UMG 508 power analyser (Modbus RTU / Modbus TCP)
UMG 508 power analyser from firmware release 2.x, per Modbus address list 1.042.008.9.b (08/2022).
Also known as: UMG508, UMG 508, Janitza UMG508 - Power meter (power analyser)
Janitza UMG 605 power quality analyser (Modbus RTU)
UMG 605 (the original, non-PRO model), per Modbus address list 1.038.009.7.a. For the UMG 605-PRO use its own map.
Also known as: UMG605, UMG 605, Janitza UMG605 - Energy meter
KOSTAL KOSTAL Smart Energy Meter (KSEM G1 / G2)
KOSTAL Smart Energy Meter generation 1 and 2, firmware 2.6.0 (interface description dated 13.03.2025); OBIS-coded internal registers only.
Also known as: KSEM, KSEM G1, KSEM G2, KOSTAL Smart Energy Meter
All power & energy meters Modbus register maps →
Source: Modbus-RTU protocol specification for DSZ15DZMOD V1.6 (English version) · V1.6 · rev. 2023-06. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.