- Home
- Modbus register maps
- Setra Systems
- Setra Power Meter (SPM) multi-circuit power meter
Power meter (multi-circuit) · Modbus register map
Setra Systems Setra Power Meter (SPM) multi-circuit power meter Modbus register map
Updated 17 November 2026
The Setra Power Meter is a multi-circuit meter with two voltage inputs and up to 48 configurable loads, each with three phases of CT inputs, reachable over Modbus RTU or Modbus TCP. Values are 32-bit floats and unsigned integers, most significant byte first. This map covers device identity and settings, both voltage inputs (voltages, angles, THD, frequency, service type) and the full Load 1 block with its three phases; Loads 2-48 repeat the same layout at higher addresses.
This page lists 132 Modbus registers for the Setra Systems Setra Power Meter (SPM) multi-circuit power meter — 0 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Setra Systems’s own free documentation (linked below) and checked against it.
- Manufacturer
- Setra Systems
- Model
- Setra Power Meter (SPM) multi-circuit power meter
- Equipment type
- Power meter (multi-circuit)
- Registers
- 132 (0 writable)
- Transport
- Modbus RTU, Modbus TCP
- Default unit ID
- Not stated
- Documented addressing
- 0-based (the number printed is the address on the wire)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- SPM, Setra Power Meter, SS-SPM-MODBUS_G
Integration notes: Setra Systems Setra Power Meter (SPM) multi-circuit power meter
Read input registers with function 04: voltages from absolute 104, Load 1 totals from 324-369 and phases from 404, decoding floats high word first.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 104 | Vin1_L1-N | FLOAT32 ABCD | Vin1 L1-N voltage | Read |
| IR 128 | Vin1_Freq | FLOAT32 ABCD | Frequency | Read |
| IR 324 | Load 1 total_kWh | FLOAT32 ABCD | Load 1 net kWh | Read |
| IR 352 | Load 1 total_amperage | FLOAT32 ABCD | Load 1 total current | Read |
| IR 354 | Load 1 total_kW | FLOAT32 ABCD | Load 1 total kW | Read |
| IR 360 | Load 1 total_aPF | FLOAT32 ABCD | Load 1 power factor | Read |
Enable Modbus control & writes
The list does not describe setup. It shows the meter can run Modbus TCP (the slave address row reads 0 in that mode) as well as a serial slave address.
Byte order & addressing
- Floats are ABCD.
- Register numbers are 30000 + address, not 30001 + address.
Network setup
- Check Total Loads (86) and each load's and phase's 'enabled' row to see which blocks hold live data.
Watch out for
- Disabled loads and phases still have registers; check their 'enabled' rows.
Setra Systems Setra Power Meter (SPM) multi-circuit power meter Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 0 / 30000 | Device_Name | Meter name, 80 characters. | STRING[80] | Read | ||||
| IR | 42doc 42 / 30042 | Model_Number | STRING[16] | Read | |||||
| IR | 50doc 50 / 30050 | Serial_Number | STRING[16] | Read | |||||
| IR | 58doc 58 / 30058 | Firmware_Revision | STRING[16] | Read | |||||
| IR | 78doc 78 / 30078 | Power_Factor_Sign_Convention | UINT32 | ABCD | Read | 1 = IEC; 2 = IEEE | |||
| IR | 80doc 80 / 30080 | Demand_Window | UINT32 | ABCD | min | Read | |||
| IR | 82doc 82 / 30082 | Billing_Cycle_Day | UINT32 | ABCD | Read | ||||
| IR | 84doc 84 / 30084 | Billing_Cycle_Time | UINT32 | ABCD | s | Read | |||
| IR | 102doc 102 / 30102 | Vin1_Enabled | UINT32 | ABCD | Read | 0 = Disabled; 1 = Enabled | |||
| IR | 104doc 104 / 30104 | Vin1_L1-N | FLOAT32 | ABCD | V | Read | |||
| IR | 106doc 106 / 30106 | Vin1_L2-N | FLOAT32 | ABCD | V | Read | |||
| IR | 108doc 108 / 30108 | Vin1_L3-N | FLOAT32 | ABCD | V | Read | |||
| IR | 110doc 110 / 30110 | Vin1_L1-L2 | FLOAT32 | ABCD | V | Read | |||
| IR | 112doc 112 / 30112 | Vin1_L2-L3 | FLOAT32 | ABCD | V | Read | |||
| IR | 114doc 114 / 30114 | Vin1_L3-L1 | FLOAT32 | ABCD | V | Read | |||
| IR | 116doc 116 / 30116 | Vin1_L1_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 118doc 118 / 30118 | Vin1_L2_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 120doc 120 / 30120 | Vin1_L3_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 122doc 122 / 30122 | Vin1_L1_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 124doc 124 / 30124 | Vin1_L2_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 126doc 126 / 30126 | Vin1_L3_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 128doc 128 / 30128 | Vin1_Freq | FLOAT32 | ABCD | Hz | Read | |||
| IR | 130doc 130 / 30130 | Vin1_Expected_Line_Voltage | UINT32 | ABCD | V | Read | |||
| IR | 132doc 132 / 30132 | Vin1_Service_Type | UINT32 | ABCD | Read | 0 = None; 1 = 4-wire wye; 2 = 3-wire delta; 3 = Reserved; 4 = 3-wire single phase (split phase); 5 = 2-wire single phase | |||
| IR | 134doc 134 / 30134 | Vin1_Scaler | UINT32 | ABCD | V | Read | |||
| IR | 150doc 150 / 30150 | Vin2_Enabled | UINT32 | ABCD | Read | 0 = Disabled; 1 = Enabled | |||
| IR | 152doc 152 / 30152 | Vin2_L1-N | FLOAT32 | ABCD | V | Read | |||
| IR | 154doc 154 / 30154 | Vin2_L2-N | FLOAT32 | ABCD | V | Read | |||
| IR | 156doc 156 / 30156 | Vin2_L3-N | FLOAT32 | ABCD | V | Read | |||
| IR | 158doc 158 / 30158 | Vin2_L1-L2 | FLOAT32 | ABCD | V | Read | |||
| IR | 160doc 160 / 30160 | Vin2_L2-L3 | FLOAT32 | ABCD | V | Read | |||
| IR | 162doc 162 / 30162 | Vin2_L3-L1 | FLOAT32 | ABCD | V | Read | |||
| IR | 164doc 164 / 30164 | Vin2_L1_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 166doc 166 / 30166 | Vin2_L2_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 168doc 168 / 30168 | Vin2_L3_PA | FLOAT32 | ABCD | ° | Read | |||
| IR | 170doc 170 / 30170 | Vin2_L1_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 172doc 172 / 30172 | Vin2_L2_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 174doc 174 / 30174 | Vin2_L3_HD | FLOAT32 | ABCD | % | Read | |||
| IR | 176doc 176 / 30176 | Vin_2_Freq | FLOAT32 | ABCD | Hz | Read | |||
| IR | 178doc 178 / 30178 | Vin2_Expected_Line_Voltage | UINT32 | ABCD | V | Read | |||
| IR | 180doc 180 / 30180 | Vin2_Service_Type | UINT32 | ABCD | Read | 0 = None; 1 = 4-wire wye; 2 = 3-wire delta; 3 = Reserved; 4 = 3-wire single phase (split phase); 5 = 2-wire single phase | |||
| IR | 182doc 182 / 30182 | Vin2_Scaler | UINT32 | ABCD | V | Read | |||
| IR | 200doc 200 / 30200 | Pulse_in_1_Enabled | UINT32 | ABCD | Read | ||||
| IR | 232doc 232 / 30232 | Pulse_in_2_Enabled | UINT32 | ABCD | Read | ||||
| IR | 322doc 322 / 30322 | Load 1 enabled | UINT32 | ABCD | Read | ||||
| IR | 324doc 324 / 30324 | Load 1 total_kWh | FLOAT32 | ABCD | kWh | Read | |||
| IR | 326doc 326 / 30326 | Load 1 total_kWh+ | FLOAT32 | ABCD | kWh | Read | |||
| IR | 328doc 328 / 30328 | Load 1 total_kWh- | FLOAT32 | ABCD | kWh | Read | |||
| IR | 330doc 330 / 30330 | Load 1 total_kvarh | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 332doc 332 / 30332 | Load 1 total_kvarh+ | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 334doc 334 / 30334 | Load 1 total_kvarh- | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 336doc 336 / 30336 | Load 1 total_kvarh_Q1 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 338doc 338 / 30338 | Load 1 total_kvarh_Q2 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 340doc 340 / 30340 | Load 1 total_kvarh_Q3 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 342doc 342 / 30342 | Load 1 total_kvarh_Q4 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 344doc 344 / 30344 | Load 1 total_kVAh | FLOAT32 | ABCD | kVAh | Read | |||
| IR | 350doc 350 / 30350 | Load 1 vref | UINT32 | ABCD | Read | ||||
| IR | 352doc 352 / 30352 | Load 1 total_amperage | FLOAT32 | ABCD | A | Read | |||
| IR | 354doc 354 / 30354 | Load 1 total_kW | FLOAT32 | ABCD | kW | Read | |||
| IR | 356doc 356 / 30356 | Load 1 total_kvar | FLOAT32 | ABCD | kvar | Read | |||
| IR | 358doc 358 / 30358 | Load 1 total_kVA | FLOAT32 | ABCD | kVA | Read | |||
| IR | 360doc 360 / 30360 | Load 1 total_aPF | FLOAT32 | ABCD | Read | ||||
| IR | 362doc 362 / 30362 | Load 1 total_dPF | FLOAT32 | ABCD | Read | ||||
| IR | 364doc 364 / 30364 | Load 1 total_THD | FLOAT32 | ABCD | % | Read | |||
| IR | 366doc 366 / 30366 | Load 1 total_Demand_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 368doc 368 / 30368 | Load 1 total_PD_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 402doc 402 / 30402 | Phase L1 enabled | UINT32 | ABCD | Read | ||||
| IR | 404doc 404 / 30404 | Phase_L1_kWh | FLOAT32 | ABCD | kWh | Read | |||
| IR | 406doc 406 / 30406 | Phase_L1_kWh+ | FLOAT32 | ABCD | kWh | Read | |||
| IR | 408doc 408 / 30408 | Phase_L1_kWh- | FLOAT32 | ABCD | kWh | Read | |||
| IR | 410doc 410 / 30410 | Phase_L1_kvarh | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 412doc 412 / 30412 | Phase_L1_kvarh+ | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 414doc 414 / 30414 | Phase_L1_kvarh- | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 416doc 416 / 30416 | Phase_L1_kvarh_Q1 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 418doc 418 / 30418 | Phase_L1_kvarh_Q2 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 420doc 420 / 30420 | Phase_L1_kvarh_Q3 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 422doc 422 / 30422 | Phase_L1_kvarh_Q4 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 424doc 424 / 30424 | Phase_L1_kVAh | FLOAT32 | ABCD | kVAh | Read | |||
| IR | 430doc 430 / 30430 | Phase_L1_Amps | FLOAT32 | ABCD | A | Read | |||
| IR | 432doc 432 / 30432 | Phase_L1_kW | FLOAT32 | ABCD | kW | Read | |||
| IR | 434doc 434 / 30434 | Phase_L1_kvar | FLOAT32 | ABCD | kvar | Read | |||
| IR | 436doc 436 / 30436 | Phase_L1_kVA | FLOAT32 | ABCD | kVA | Read | |||
| IR | 438doc 438 / 30438 | Phase_L1_aPF | FLOAT32 | ABCD | Read | ||||
| IR | 440doc 440 / 30440 | Phase_L1_dPF | FLOAT32 | ABCD | Read | ||||
| IR | 442doc 442 / 30442 | Phase_L1_THD | FLOAT32 | ABCD | % | Read | |||
| IR | 444doc 444 / 30444 | Phase_L1_Demand_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 446doc 446 / 30446 | Phase_L1_PD_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 448doc 448 / 30448 | Phase_L1_PC | UINT32 | ABCD | Read | ||||
| IR | 462doc 462 / 30462 | Phase L2 enabled | UINT32 | ABCD | Read | ||||
| IR | 464doc 464 / 30464 | Phase_L2_kWh | FLOAT32 | ABCD | kWh | Read | |||
| IR | 466doc 466 / 30466 | Phase_L2_kWh+ | FLOAT32 | ABCD | kWh | Read | |||
| IR | 468doc 468 / 30468 | Phase_L2_kWh- | FLOAT32 | ABCD | kWh | Read | |||
| IR | 470doc 470 / 30470 | Phase_L2_kvarh | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 472doc 472 / 30472 | Phase_L2_kvarh+ | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 474doc 474 / 30474 | Phase_L2_kvarh- | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 476doc 476 / 30476 | Phase_L2_kvarh_Q1 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 478doc 478 / 30478 | Phase_L2_kvarh_Q2 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 480doc 480 / 30480 | Phase_L2_kvarh_Q3 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 482doc 482 / 30482 | Phase_L2_kvarh_Q4 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 484doc 484 / 30484 | Phase_L2_kVAh | FLOAT32 | ABCD | kVAh | Read | |||
| IR | 490doc 490 / 30490 | Phase_L2_Amps | FLOAT32 | ABCD | A | Read | |||
| IR | 492doc 492 / 30492 | Phase_L2_kW | FLOAT32 | ABCD | kW | Read | |||
| IR | 494doc 494 / 30494 | Phase_L2_kvar | FLOAT32 | ABCD | kvar | Read | |||
| IR | 496doc 496 / 30496 | Phase_L2_kVA | FLOAT32 | ABCD | kVA | Read | |||
| IR | 498doc 498 / 30498 | Phase_L2_aPF | FLOAT32 | ABCD | Read | ||||
| IR | 500doc 500 / 30500 | Phase_L2_dPF | FLOAT32 | ABCD | Read | ||||
| IR | 502doc 502 / 30502 | Phase_L2_THD | FLOAT32 | ABCD | % | Read | |||
| IR | 504doc 504 / 30504 | Phase_L2_Demand_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 506doc 506 / 30506 | Phase_L2_PD_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 508doc 508 / 30508 | Phase_L2_PC | UINT32 | ABCD | Read | ||||
| IR | 522doc 522 / 30522 | Phase L3 enabled | UINT32 | ABCD | Read | ||||
| IR | 524doc 524 / 30524 | Phase_L3_kWh | FLOAT32 | ABCD | kWh | Read | |||
| IR | 526doc 526 / 30526 | Phase_L3_kWh+ | FLOAT32 | ABCD | kWh | Read | |||
| IR | 528doc 528 / 30528 | Phase_L3_kWh- | FLOAT32 | ABCD | kWh | Read | |||
| IR | 530doc 530 / 30530 | Phase_L3_kvarh | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 532doc 532 / 30532 | Phase_L3_kvarh+ | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 534doc 534 / 30534 | Phase_L3_kvarh- | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 536doc 536 / 30536 | Phase_L3_kvarh_Q1 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 538doc 538 / 30538 | Phase_L3_kvarh_Q2 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 540doc 540 / 30540 | Phase_L3_kvarh_Q3 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 542doc 542 / 30542 | Phase_L3_kvarh_Q4 | FLOAT32 | ABCD | kvarh | Read | |||
| IR | 544doc 544 / 30544 | Phase_L3_kVAh | FLOAT32 | ABCD | kVAh | Read | |||
| IR | 550doc 550 / 30550 | Phase_L3_Amps | FLOAT32 | ABCD | A | Read | |||
| IR | 552doc 552 / 30552 | Phase_L3_kW | FLOAT32 | ABCD | kW | Read | |||
| IR | 554doc 554 / 30554 | Phase_L3_kvar | FLOAT32 | ABCD | kvar | Read | |||
| IR | 556doc 556 / 30556 | Phase_L3_kVA | FLOAT32 | ABCD | kVA | Read | |||
| IR | 558doc 558 / 30558 | Phase_L3_aPF | FLOAT32 | ABCD | Read | ||||
| IR | 560doc 560 / 30560 | Phase_L3_dPF | FLOAT32 | ABCD | Read | ||||
| IR | 562doc 562 / 30562 | Phase_L3_THD | FLOAT32 | ABCD | % | Read | |||
| IR | 564doc 564 / 30564 | Phase_L3_Demand_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 566doc 566 / 30566 | Phase_L3_PD_KW | FLOAT32 | ABCD | kW | Read | |||
| IR | 568doc 568 / 30568 | Phase_L3_PC | UINT32 | ABCD | Read |
Notes on this map
- Word order: every block of uint32/float32 values is headed 'Data Format: Big-Endian (high byte first, or most significant byte first)'. That describes the 32-bit values themselves, so the most significant byte, and with it the high word, comes first in the lower register: ABCD.
- Loads 2-48 follow the Load 1 layout in later blocks (Load 2 starts at absolute 580); they are not repeated here.
- Left out: 'id' identifier rows, pulse counts and scalers (user-configurable units), the Modbus slave address row, the date/time string and reserved rows.
- Input registers (function 04) are implied by the 3xxxx register numbers.
- Left out: the kVAh+ and kVAh- rows (total and per phase). Their names say apparent energy but the unit column prints kilo-volt-amperes-reactive-hour, so the unit is not settled.
- Addressing: the 'Absolute Address' column starts at 0 for the first register (Device_Name), so it is used as the wire address; the 'Modbus Register' column is that number plus 30000.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Setra Systems Setra Power Meter (SPM) multi-circuit power meter
What Modbus registers does the Setra Systems Setra Power Meter (SPM) multi-circuit power meter have?
This map lists 132 registers: 132 input registers. 0 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Setra Systems Setra Power Meter (SPM) multi-circuit power meter Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 0-based (the number printed is the address on the wire). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Each row gives an 'Absolute Address' and a 'Modbus Register'. The list starts at absolute address 0 (Device_Name, register 30000), and every register number is 30000 + the absolute address, so the absolute address is the wire address for an input-register read: Vin1 L1-N is absolute 104 (register 30104).
What byte order does the Setra Systems Setra Power Meter (SPM) multi-circuit power meter use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Setra Systems Setra Power Meter (SPM) multi-circuit power meter?
Start with IR 104 Vin1_L1-N (Vin1 L1-N voltage); IR 128 Vin1_Freq (Frequency); IR 324 Load 1 total_kWh (Load 1 net kWh); IR 352 Load 1 total_amperage (Load 1 total current); IR 354 Load 1 total_kW (Load 1 total kW); IR 360 Load 1 total_aPF (Load 1 power factor).
How do I enable Modbus control of the Setra Systems Setra Power Meter (SPM) multi-circuit power meter?
The list does not describe setup. It shows the meter can run Modbus TCP (the slave address row reads 0 in that mode) as well as a serial slave address.
Where is the official Setra Systems Setra Power Meter (SPM) multi-circuit power meter Modbus documentation?
The source is Setra Power Meter Modbus Register Master List (SS-SPM-MODBUS_G), published free by Setra Systems at https://content.setra.com/hubfs/modbus-register-list.pdf.
Other power & energy meters register maps
- Energy meter (heat / cooling meter)
Sontex Supercal 531 / Superstatic 440 / 449 with Modbus EIA-485 module
Sontex Modbus EIA-485 plug-in module in a Supercal 531 integrator or Superstatic 440/449 heat meter, integrator firmware 3.7 or later; user manual V05 (2019-09).
Also known as: Supercal 531, Superstatic 440, Superstatic 449, Sontex Modbus EIA-485 module, 0531P217 - Energy meter
ABB EQ meter A43 / A44 (Modbus RTU)
ABB EQ A43 (direct connected) and A44 (transformer connected) three-phase DIN meters whose RS-485 port is set to Modbus.
Also known as: A43, A44, EQ A43, EQ A44 - Power meter
Accuenergy AcuRev 1310 series DIN-rail power meter
Accuenergy AcuRev 1310 series (1312/1313/1314) DIN-rail meters, Modbus map workbook revision 1.1.
Also known as: AcuRev 1312, AcuRev 1313, AcuRev 1314, AcuRev 1310 - Power meter (universal measuring / power quality device)
Camille Bauer Metrawatt SINEAX CAM universal measurement device (Modbus/TCP)
SINEAX CAM with Ethernet (Modbus/TCP) bus card; document W 157471, change 2014-018. Instantaneous values, THD/TDD, system analysis, analog inputs, I/O states.
Also known as: SINEAX CAM, CAM - Energy meter
Carlo Gavazzi EM24-IS (SFA and SFB models)
EM24-DIN AV2/AV5 IS SFA and SFB versions (identification codes 1696-1699), protocol revision 2.0.
Also known as: EM24DINAV23XISSFA, EM24DINAV53XISSFA, EM24DINAV23XISSFB, EM24DINAV53XISSFB, EM24 SFA, EM24 SFB - Power meter (power analyzer)
Carlo Gavazzi WM14 Advanced / CPT-DIN Advanced power analyzer (legacy)
WM14 Advanced (revision 5 onward) and CPT-DIN Advanced (revision 6 onward) with RS485 (or RS232 on CPT-DIN), protocol version 2 revision 2 (2008-01-09).
Also known as: WM14-96 Advanced, WM14 A, CPT-DIN Advanced, CPT A, CPT-DIN A
All power & energy meters Modbus register maps →
Source: Setra Power Meter Modbus Register Master List · SS-SPM-MODBUS_G. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.