- Home
- Modbus register maps
- Acromag
- BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
Sensor (Ethernet analog input module) · Modbus register map
Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) Modbus register map
Updated 19 November 2026
The Acromag BusWorks XT1211 (current) and XT1221 (voltage) are 8-channel differential analog input modules on Modbus TCP. The Modbus map is read-only: eight normalized channel values and a heartbeat counter.
This page lists 9 Modbus registers for the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) — 0 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Acromag’s own free documentation (linked below) and checked against it.
- Manufacturer
- Acromag
- Model
- BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
- Equipment type
- Sensor (Ethernet analog input module)
- Registers
- 9 (0 writable)
- Transport
- Modbus TCP
- Default unit ID
- Not stated
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- Also known as
- XT1211-000, XT1221-000, XT1211, XT1221, BusWorks XT1211, BusWorks XT1221
Integration notes: Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
Read input registers 0-7 for the eight channels and convert counts to engineering units from the configured range (30000 = 100 %). Watch register 8 to confirm fresh data.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | CH 00 data | INT16 | Channel 0 | Read |
| IR 1 | CH 01 data | INT16 | Channel 1 | Read |
| IR 7 | CH 07 data | INT16 | Channel 7 | Read |
| IR 8 | Heart beat | UINT16 | Heartbeat | Read |
Enable Modbus control & writes
Modbus TCP needs no enabling; set the IP address (default static 192.168.1.100) and channel ranges with the USB configuration software before connecting to the network.
Byte order & addressing
- Values are normalized counts (30000 or 20000 = 100 %), not volts or milliamps.
Network setup
- Configure IP address, input ranges and averaging over USB before connecting to the network.
Watch out for
- Use a USB isolator when configuring with grounded inputs connected, or a ground loop can shift readings.
Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 | CH 00 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 1doc 30002 | CH 01 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 2doc 30003 | CH 02 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 3doc 30004 | CH 03 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 4doc 30005 | CH 04 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 5doc 30006 | CH 05 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 6doc 30007 | CH 06 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 7doc 30008 | CH 07 data | Normalized count: ±30000 = ±100 % of the range (±20000 in legacy mode). | INT16 | Read | ||||
| IR | 8doc 30009 | Heart beat | Counts 0-65535 on each host transfer, then wraps. | UINT16 | Read |
Notes on this map
- Channel values are normalized counts, not engineering units: bipolar ranges read -30000 to +30000 for -100 % to +100 %, unipolar ranges 0-30000; with legacy support enabled the span is 20000 instead. The range is chosen per channel in the USB software (XT1211: ±20 mA, 0-20 mA, 0-11.17 mA, 4-20 mA; XT1221: ±10 V, ±5 V, 0-10 V, 0-5 V).
- The map prints the Modicon reference and a 0-based address column; the address column is sent on the wire.
- There are no configuration registers: ranges, averaging and IP settings are set only with the USB configuration software.
- The Unit ID is ignored and echoed back in Modbus TCP.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
What Modbus registers does the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) have?
This map lists 9 registers: 9 input registers. 0 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The register map prints both the reference (00001, 10001, 30001, 40001) and the 0-based address column; the address column is what goes on the wire.
What are the minimum Modbus registers to integrate the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)?
Start with IR 0 CH 00 data (Channel 0); IR 1 CH 01 data (Channel 1); IR 7 CH 07 data (Channel 7); IR 8 Heart beat (Heartbeat).
How do I enable Modbus control of the Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)?
Modbus TCP needs no enabling; set the IP address (default static 192.168.1.100) and channel ranges with the USB configuration software before connecting to the network.
Where is the official Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP) Modbus documentation?
The source is BusWorks XT Series Model XT1211/XT1221-000 8 CH Differential Current/Voltage Input User's Manual (8500951K), revision 2022-11-18, published free by Acromag at https://www.acromag.com/wp-content/uploads/2019/06/Acromag-XT1211-and-XT1221_951K-User-Manual.pdf.
More Acromag Modbus register maps
- Sensor (Ethernet digital I/O module)
Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)
BusWorks XT1121-000 per user's manual 8500950P (revision P, 18 Nov 2022).
Also known as: XT1121-000, XT1121, BusWorks XT1121 - Sensor (Ethernet analog output module)
Acromag BusWorks XT1531-000 4-channel current output + 4 digital I/O (Modbus TCP)
BusWorks XT1531-000 per its user's manual (file revision H, 18 Nov 2022).
Also known as: XT1531-000, XT1531, BusWorks XT1531 - Sensor (Ethernet analog output module)
Acromag BusWorks XT1541-000 8-channel voltage output + 4 digital I/O (Modbus TCP)
BusWorks XT1541-000 per its user's manual (file revision H, 18 Nov 2022).
Also known as: XT1541-000, XT1541, BusWorks XT1541
Other remote i/o modules register maps
- Sensor / remote digital I/O module
ICP DAS tM series digital I/O modules tM-P4C4, tM-C8, tM-P8 (Modbus RTU)
tM-P4C4 (4 DI + 4 DO), tM-C8 (8 DO) and tM-P8 (8 DI) with the Modbus RTU protocol selected, per the tM Series DIO User Manual Rev A1.4.
Also known as: tM-P4C4, tM-C8, tM-P8 - Sensor (remote I/O module, digital inputs/outputs)
Seneca R-32DIDO Ethernet I/O (32 digital inputs/outputs)
R-32DIDO (R-32DIDO-1 / R-32DIDO-2) in the Series R I/O manual MI-00604-29-EN.
Also known as: R32DIDO, R-32DIDO-1, R-32DIDO-2, Seneca R series 32DIDO - Sensor (I/O module, 8 analog inputs)
Seneca Z-8AI 8-channel analog input module
Seneca Z-8AI DIN-rail module with 8 voltage/current inputs and RS-485 Modbus RTU, per user manual MI00259-3-EN.
Also known as: Z-8AI - Sensor (remote I/O module)
Unipi Technology Unipi Extension xS52 resistance input module
Unipi Extension xS52 RS-485 module per the Unipi Extension xS52 Modbus map v2.0.
Also known as: Unipi Extension xS52, xS52 - Sensor / remote I/O module
Brainboxes ED-588 Ethernet digital I/O (Modbus TCP)
Brainboxes ED-588 Ethernet I/O module with the protocol set to Modbus TCP.
Also known as: ED-588, ED588 - Sensor (remote I/O module)
Moxa ioLogik R1214 RS-485 remote I/O
ioLogik R1214 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1214, R1214, R1214-T
All remote i/o modules Modbus register maps →
Source: BusWorks XT Series Model XT1211/XT1221-000 8 CH Differential Current/Voltage Input User's Manual · 8500951K · rev. 2022-11-18. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.