- Home
- Modbus register maps
- Acromag
- BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)
Sensor (Ethernet digital I/O module) · Modbus register map
Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) Modbus register map
Updated 19 November 2026
The Acromag BusWorks XT1121-000 is a Modbus TCP Ethernet module with 16 active-high inputs paired with 16 high-side (sourcing) outputs. Its Modbus map is I/O only: four input-state words, a heartbeat counter and four output-command words; all setup is done over USB.
This page lists 9 Modbus registers for the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) — 4 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Acromag’s own free documentation (linked below) and checked against it.
- Manufacturer
- Acromag
- Model
- BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)
- Equipment type
- Sensor (Ethernet digital I/O module)
- Registers
- 9 (4 writable)
- Transport
- Modbus TCP
- Default unit ID
- Not stated
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- Also known as
- XT1121-000, XT1121, BusWorks XT1121
Integration notes: Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)
Read input registers 0-3 for input states and write holding registers 0-3 to drive the outputs, four channels per word. Watch input register 4 to confirm the module is updating.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | Input State Group 0 (CH0-3) | BITMAP16 | Inputs CH0-3 | Read |
| IR 1 | Input State Group 1 (CH4-7) | BITMAP16 | Inputs CH4-7 | Read |
| IR 4 | Heart Beat | UINT16 | Heartbeat | Read |
| HR 0 | Set Output State Group 0 (CH0-3) | BITMAP16 | Outputs CH0-3 | Read/write |
| HR 1 | Set Output State Group 1 (CH4-7) | BITMAP16 | Outputs CH4-7 | Read/write |
Enable Modbus control & writes
Modbus TCP needs no enabling; set the IP address (default static 192.168.1.100) with the USB configuration software before connecting to the network. The manual does not print the TCP port number.
Communication loss & watchdog
Per-channel watchdog (5-65534 s, 0 or 65535 = off) set in the USB software: with no read/write activity for that time the output goes to its chosen watchdog state and stays there until written again.
Byte order & addressing
- Output commands are lost at reset (outputs start OFF); they are not kept in flash.
- The Unit ID is ignored and echoed back.
Network setup
- Configure IP address, input invert and watchdog over USB before connecting to the network.
- Outputs need 6-32 V excitation on EXC to work.
Watch out for
- If an output is on, the paired input reads high: turn the output off to monitor a field signal on that channel.
Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 | Input State Group 0 (CH0-3) | Input states, bit 0 = lowest channel; 1 = high (no invert). | BITMAP16 | Read | bit 0 = CH0; bit 1 = CH1; bit 2 = CH2; bit 3 = CH3 | |||
| IR | 1doc 30002 | Input State Group 1 (CH4-7) | Input states, bit 0 = lowest channel; 1 = high (no invert). | BITMAP16 | Read | bit 0 = CH4; bit 1 = CH5; bit 2 = CH6; bit 3 = CH7 | |||
| IR | 2doc 30003 | Input State Group 2 (CH8-11) | Input states, bit 0 = lowest channel; 1 = high (no invert). | BITMAP16 | Read | bit 0 = CH8; bit 1 = CH9; bit 2 = CH10; bit 3 = CH11 | |||
| IR | 3doc 30004 | Input State Group 3 (CH12-15) | Input states, bit 0 = lowest channel; 1 = high (no invert). | BITMAP16 | Read | bit 0 = CH12; bit 1 = CH13; bit 2 = CH14; bit 3 = CH15 | |||
| IR | 4doc 30005 | Heart Beat | Counter that rises by 1 per transfer and wraps at 65535. | UINT16 | Read | ||||
| HR | 0doc 40001 | Set Output State Group 0 (CH0-3) | Output commands, bit 0 = lowest channel; 1 = on (sourcing). | BITMAP16 | Read/write | bit 0 = CH0; bit 1 = CH1; bit 2 = CH2; bit 3 = CH3 | |||
| HR | 1doc 40002 | Set Output State Group 1 (CH4-7) | Output commands, bit 0 = lowest channel; 1 = on (sourcing). | BITMAP16 | Read/write | bit 0 = CH4; bit 1 = CH5; bit 2 = CH6; bit 3 = CH7 | |||
| HR | 2doc 40003 | Set Output State Group 2 (CH8-11) | Output commands, bit 0 = lowest channel; 1 = on (sourcing). | BITMAP16 | Read/write | bit 0 = CH8; bit 1 = CH9; bit 2 = CH10; bit 3 = CH11 | |||
| HR | 3doc 40004 | Set Output State Group 3 (CH12-15) | Output commands, bit 0 = lowest channel; 1 = on (sourcing). | BITMAP16 | Read/write | bit 0 = CH12; bit 1 = CH13; bit 2 = CH14; bit 3 = CH15 |
Notes on this map
- Each group word covers four channels in bits 0-3; bits 4-15 are unused and read 0.
- Input words show the real level at each channel, so they also read back the state of the paired output.
- There are no configuration registers: IP settings, input invert and watchdog are set only with the USB configuration software.
- The manual's revision table lists 8500950P as released 18 Nov 2022; the download URL path still carries a 2019 date.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)
What Modbus registers does the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) have?
This map lists 9 registers: 5 input registers, 4 holding registers. 4 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The register map prints both the reference (30001, 40001) and the 0-based address column (0, 1, 2...); the address column is what goes on the wire.
What are the minimum Modbus registers to integrate the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)?
Start with IR 0 Input State Group 0 (CH0-3) (Inputs CH0-3); IR 1 Input State Group 1 (CH4-7) (Inputs CH4-7); IR 4 Heart Beat (Heartbeat); HR 0 Set Output State Group 0 (CH0-3) (Outputs CH0-3); HR 1 Set Output State Group 1 (CH4-7) (Outputs CH4-7).
How do I enable Modbus control of the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP)?
Modbus TCP needs no enabling; set the IP address (default static 192.168.1.100) with the USB configuration software before connecting to the network. The manual does not print the TCP port number.
What happens when the Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) loses Modbus communication?
Per-channel watchdog (5-65534 s, 0 or 65535 = off) set in the USB software: with no read/write activity for that time the output goes to its chosen watchdog state and stays there until written again.
Where is the official Acromag BusWorks XT1121-000 16-channel sourcing digital I/O (Modbus TCP) Modbus documentation?
The source is BusWorks XT Series Model XT1121-000 16-Channel Sourcing Digital I/O User's Manual (8500950P), revision 2022-11-18, published free by Acromag at https://www.acromag.com/wp-content/uploads/2019/06/Acromag-XT1121_950P-User-Manual.pdf.
More Acromag Modbus register maps
- Sensor (Ethernet analog input module)
Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
BusWorks XT1211-000 (current) and XT1221-000 (voltage) per user's manual 8500951K.
Also known as: XT1211-000, XT1221-000, XT1211, XT1221, BusWorks XT1211, BusWorks XT1221 - Sensor (Ethernet analog output module)
Acromag BusWorks XT1531-000 4-channel current output + 4 digital I/O (Modbus TCP)
BusWorks XT1531-000 per its user's manual (file revision H, 18 Nov 2022).
Also known as: XT1531-000, XT1531, BusWorks XT1531 - Sensor (Ethernet analog output module)
Acromag BusWorks XT1541-000 8-channel voltage output + 4 digital I/O (Modbus TCP)
BusWorks XT1541-000 per its user's manual (file revision H, 18 Nov 2022).
Also known as: XT1541-000, XT1541, BusWorks XT1541
Other remote i/o modules register maps
- Sensor (PWM output and counter input module)
ICP DAS M-7088 8-channel PWM output / counter input module (Modbus RTU)
ICP DAS M-7088 eight-channel PWM output module with eight digital inputs and counters, Modbus RTU firmware.
Also known as: M-7088, M7088 - Sensor (remote I/O module, digital inputs/outputs)
Seneca R-16DI-8DO Ethernet I/O (16 digital inputs, 8 digital outputs)
R-16DI-8DO in the Series R I/O manual MI-00604-29-EN.
Also known as: R16DI8DO, R-16DI-8DO, Seneca R series 16DI 8DO - Sensor (I/O module, 4 thermocouple inputs)
Seneca Z-4TC 4-channel thermocouple input module
Seneca Z-4TC DIN-rail module with four thermocouple/mV inputs and RS-485 Modbus RTU, per user manual MI00258-3-EN.
Also known as: Z-4TC - Sensor (remote I/O module)
Unipi Technology Unipi Extension xS51 I/O module
Unipi Extension xS51 RS-485 module per the Unipi Extension xS51 Modbus map v2.0.
Also known as: Unipi Extension xS51, xS51 - Sensor / remote I/O module
Brainboxes ED-538 Ethernet digital I/O (Modbus TCP)
Brainboxes ED-538 Ethernet I/O module with the protocol set to Modbus TCP.
Also known as: ED-538, ED538 - Sensor (remote I/O module)
Moxa ioLogik R1212 RS-485 remote I/O
ioLogik R1212 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1212, R1212, R1212-T
All remote i/o modules Modbus register maps →
Source: BusWorks XT Series Model XT1121-000 16-Channel Sourcing Digital I/O User's Manual · 8500950P · rev. 2022-11-18. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.