- Home
- Modbus register maps
- Moxa
- ioLogik R1212 RS-485 remote I/O
Sensor (remote I/O module) · Modbus register map
Moxa ioLogik R1212 RS-485 remote I/O Modbus register map
Updated 17 November 2026
The ioLogik R1212 is a Moxa RS-485 Modbus RTU remote I/O module with 8 digital inputs plus 8 configurable DIO channels with pulse output. It supports a repeater or dual RS-485 mode and a Modbus host-connection watchdog with safe-mode output states. This map covers the shared system registers (model, watchdog, serial settings) and the DI, DIO and DO pulse channels.
This page lists 312 Modbus registers for the Moxa ioLogik R1212 RS-485 remote I/O — 243 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Moxa’s own free documentation (linked below) and checked against it.
- Manufacturer
- Moxa
- Model
- ioLogik R1212 RS-485 remote I/O
- Equipment type
- Sensor (remote I/O module)
- Registers
- 312 (243 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Default serial
- 9600 baud, 8N1
- Documented addressing
- hexadecimal, 0-based
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- ioLogik R1212, R1212, R1212-T
Integration notes: Moxa ioLogik R1212 RS-485 remote I/O
Poll the I/O block with the function code shown for each register (01/02 for bits, 03/04 for words). Enable the Modbus watchdog (0x7564, timeout 0x7565) so outputs and counters fall back to their safe-mode settings if the master stops polling.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 30000 | SYS_modelID | UINT16 | Model ID check | Read |
| HR 30052 | SYS_modbusWatchdogFuntion | UINT16 | Enable communication watchdog | Read/write |
| HR 30053 | SYS_modbusWatchdogTimeout | UINT16 | Watchdog timeout | Read/write |
| DI 0 | DI-00_status | BIT | First digital input | Read |
| IR 32 | DI-00_counterValue | UINT32 ABCD | First counter value | Read |
| CO 320 | DO-00_status | BIT | First output on/off | Read/write |
Enable Modbus control & writes
Set the device ID (1-99) on the two rotary dials. Put the Initial/Run switch on Initial to configure the unit at 9600 baud, no parity, 8 data bits, 1 stop bit (with ioSearch or the SYS_port* registers), then switch back to Run.
Communication loss & watchdog
SYS_modbusWatchdogFuntion (0x7564) enables the host-connection watchdog, SYS_modbusWatchdogTimeout (0x7565) sets the timeout in seconds (factory default 10 s), SYS_modbusWatchdogStatus (0x7566) shows a timeout. It is disabled by default; safe-status settings only act when it is enabled.
Byte order & addressing
- System registers sit at 0x7530 and up (six-digit references 330001/430002).
- Write 404 to SYS_restartDevice or SYS_loadFactoryDefault to trigger them.
Network setup
- Device ID 1-99 on the rotary dials (x1 and x10).
- The Dual/Rep switch selects two separate RS-485 ports or repeater mode; SYS_rs485PortMode reports which is active.
- Baud rate codes: 1=1200 ... 4=9600, 5=19200 ... 9=921600.
Watch out for
- Factory defaults (reset button held 5 s, ioSearch, or SYS_loadFactoryDefault) return the serial settings to 9600 n 8 1 and disable the watchdog.
Moxa ioLogik R1212 RS-485 remote I/O Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| CO | 0doc 0x0000 | DI-00_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 1doc 0x0001 | DI-01_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 2doc 0x0002 | DI-02_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 3doc 0x0003 | DI-03_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 4doc 0x0004 | DI-04_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 5doc 0x0005 | DI-05_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 6doc 0x0006 | DI-06_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 7doc 0x0007 | DI-07_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 8doc 0x0008 | DI-08_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 9doc 0x0009 | DI-09_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 10doc 0x000A | DI-10_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 11doc 0x000B | DI-11_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 12doc 0x000C | DI-12_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 13doc 0x000D | DI-13_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 14doc 0x000E | DI-14_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 15doc 0x000F | DI-15_counterStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 32doc 0x0020 | DI-00_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 33doc 0x0021 | DI-01_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 34doc 0x0022 | DI-02_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 35doc 0x0023 | DI-03_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 36doc 0x0024 | DI-04_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 37doc 0x0025 | DI-05_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 38doc 0x0026 | DI-06_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 39doc 0x0027 | DI-07_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 40doc 0x0028 | DI-08_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 41doc 0x0029 | DI-09_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 42doc 0x002A | DI-10_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 43doc 0x002B | DI-11_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 44doc 0x002C | DI-12_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 45doc 0x002D | DI-13_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 46doc 0x002E | DI-14_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 47doc 0x002F | DI-15_counterReset | BIT | Read/write | 1 = reset to initial value | ||||
| CO | 64doc 0x0040 | DI-00_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 65doc 0x0041 | DI-01_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 66doc 0x0042 | DI-02_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 67doc 0x0043 | DI-03_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 68doc 0x0044 | DI-04_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 69doc 0x0045 | DI-05_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 70doc 0x0046 | DI-06_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 71doc 0x0047 | DI-07_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 72doc 0x0048 | DI-08_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 73doc 0x0049 | DI-09_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 74doc 0x004A | DI-10_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 75doc 0x004B | DI-11_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 76doc 0x004C | DI-12_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 77doc 0x004D | DI-13_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 78doc 0x004E | DI-14_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 79doc 0x004F | DI-15_counterOverflowFlag | BIT | Read/write | 1 = clear overflow flag | ||||
| CO | 96doc 0x0060 | DI-00_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 97doc 0x0061 | DI-01_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 98doc 0x0062 | DI-02_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 99doc 0x0063 | DI-03_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 100doc 0x0064 | DI-04_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 101doc 0x0065 | DI-05_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 102doc 0x0066 | DI-06_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 103doc 0x0067 | DI-07_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 104doc 0x0068 | DI-08_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 105doc 0x0069 | DI-09_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 106doc 0x006A | DI-10_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 107doc 0x006B | DI-11_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 108doc 0x006C | DI-12_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 109doc 0x006D | DI-13_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 110doc 0x006E | DI-14_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 111doc 0x006F | DI-15_counterPowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 128doc 0x0080 | DI-00_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 129doc 0x0081 | DI-01_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 130doc 0x0082 | DI-02_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 131doc 0x0083 | DI-03_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 132doc 0x0084 | DI-04_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 133doc 0x0085 | DI-05_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 134doc 0x0086 | DI-06_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 135doc 0x0087 | DI-07_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 136doc 0x0088 | DI-08_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 137doc 0x0089 | DI-09_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 138doc 0x008A | DI-10_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 139doc 0x008B | DI-11_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 140doc 0x008C | DI-12_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 141doc 0x008D | DI-13_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 142doc 0x008E | DI-14_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 143doc 0x008F | DI-15_counterSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 160doc 0x00A0 | DI-00_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 161doc 0x00A1 | DI-01_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 162doc 0x00A2 | DI-02_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 163doc 0x00A3 | DI-03_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 164doc 0x00A4 | DI-04_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 165doc 0x00A5 | DI-05_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 166doc 0x00A6 | DI-06_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 167doc 0x00A7 | DI-07_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 168doc 0x00A8 | DI-08_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 169doc 0x00A9 | DI-09_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 170doc 0x00AA | DI-10_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 171doc 0x00AB | DI-11_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 172doc 0x00AC | DI-12_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 173doc 0x00AD | DI-13_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 174doc 0x00AE | DI-14_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 175doc 0x00AF | DI-15_counterPowerOffStorage | BIT | Read/write | 0 = Disable; 1 = Enable | ||||
| CO | 320doc 0x0140 | DO-00_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 321doc 0x0141 | DO-01_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 322doc 0x0142 | DO-02_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 323doc 0x0143 | DO-03_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 324doc 0x0144 | DO-04_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 325doc 0x0145 | DO-05_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 326doc 0x0146 | DO-06_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 327doc 0x0147 | DO-07_status | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 352doc 0x0160 | DO-00_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 353doc 0x0161 | DO-01_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 354doc 0x0162 | DO-02_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 355doc 0x0163 | DO-03_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 356doc 0x0164 | DO-04_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 357doc 0x0165 | DO-05_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 358doc 0x0166 | DO-06_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 359doc 0x0167 | DO-07_powerOnStatus | BIT | Read/write | 0 = OFF; 1 = ON | ||||
| CO | 384doc 0x0180 | DO-00_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 385doc 0x0181 | DO-01_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 386doc 0x0182 | DO-02_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 387doc 0x0183 | DO-03_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 388doc 0x0184 | DO-04_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 389doc 0x0185 | DO-05_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 390doc 0x0186 | DO-06_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 391doc 0x0187 | DO-07_pulseStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 416doc 0x01A0 | DO-00_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 417doc 0x01A1 | DO-01_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 418doc 0x01A2 | DO-02_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 419doc 0x01A3 | DO-03_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 420doc 0x01A4 | DO-04_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 421doc 0x01A5 | DO-05_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 422doc 0x01A6 | DO-06_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 423doc 0x01A7 | DO-07_pulsePowerOnStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 448doc 0x01C0 | DO-00_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 449doc 0x01C1 | DO-01_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 450doc 0x01C2 | DO-02_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 451doc 0x01C3 | DO-03_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 452doc 0x01C4 | DO-04_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 453doc 0x01C5 | DO-05_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 454doc 0x01C6 | DO-06_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| CO | 455doc 0x01C7 | DO-07_pulseSafeModeStatus | BIT | Read/write | 0 = STOP; 1 = START | ||||
| DI | 0doc 0x0000 | DI-00_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 1doc 0x0001 | DI-01_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 2doc 0x0002 | DI-02_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 3doc 0x0003 | DI-03_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 4doc 0x0004 | DI-04_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 5doc 0x0005 | DI-05_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 6doc 0x0006 | DI-06_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 7doc 0x0007 | DI-07_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 8doc 0x0008 | DI-08_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 9doc 0x0009 | DI-09_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 10doc 0x000A | DI-10_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 11doc 0x000B | DI-11_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 12doc 0x000C | DI-12_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 13doc 0x000D | DI-13_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 14doc 0x000E | DI-14_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 15doc 0x000F | DI-15_status | BIT | Read | 0 = OFF; 1 = ON | ||||
| DI | 10288doc 0x2830 | DIO-00_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10289doc 0x2831 | DIO-01_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10290doc 0x2832 | DIO-02_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10291doc 0x2833 | DIO-03_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10292doc 0x2834 | DIO-04_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10293doc 0x2835 | DIO-05_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10294doc 0x2836 | DIO-06_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| DI | 10295doc 0x2837 | DIO-07_mode | BIT | Read | 0 = DI; 1 = DO | ||||
| IR | 0doc 0x0000 | DI-00_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 1doc 0x0001 | DI-01_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 2doc 0x0002 | DI-02_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 3doc 0x0003 | DI-03_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 4doc 0x0004 | DI-04_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 5doc 0x0005 | DI-05_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 6doc 0x0006 | DI-06_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 7doc 0x0007 | DI-07_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 8doc 0x0008 | DI-08_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 9doc 0x0009 | DI-09_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 10doc 0x000A | DI-10_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 11doc 0x000B | DI-11_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 12doc 0x000C | DI-12_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 13doc 0x000D | DI-13_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 14doc 0x000E | DI-14_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 15doc 0x000F | DI-15_status | UINT16 | Read | 0 = OFF; 1 = ON | ||||
| IR | 32doc 0x0020 | DI-00_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 34doc 0x0022 | DI-01_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 36doc 0x0024 | DI-02_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 38doc 0x0026 | DI-03_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 40doc 0x0028 | DI-04_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 42doc 0x002A | DI-05_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 44doc 0x002C | DI-06_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 46doc 0x002E | DI-07_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 48doc 0x0030 | DI-08_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 50doc 0x0032 | DI-09_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 52doc 0x0034 | DI-10_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 54doc 0x0036 | DI-11_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 56doc 0x0038 | DI-12_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 58doc 0x003A | DI-13_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 60doc 0x003C | DI-14_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 62doc 0x003E | DI-15_counterValue | High word at this address, low word next. | UINT32 | ABCD | Read | |||
| IR | 288doc 0x0120 | DIO-00_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 289doc 0x0121 | DIO-01_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 290doc 0x0122 | DIO-02_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 291doc 0x0123 | DIO-03_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 292doc 0x0124 | DIO-04_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 293doc 0x0125 | DIO-05_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 294doc 0x0126 | DIO-06_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 295doc 0x0127 | DIO-07_mode | UINT16 | Read | 0 = DI; 1 = DO | ||||
| IR | 30000doc 0x7530 | SYS_modelID | UINT16 | Read | |||||
| IR | 30025doc 0x7549 | SYS_vendorID | UINT16 | Read | |||||
| IR | 30026doc 0x754A | SYS_unitID | UINT16 | Read | |||||
| IR | 30037doc 0x7555 | SYS_productName | STRING[20] | Read | |||||
| IR | 30058doc 0x756A | SYS_rs485PortMode | UINT16 | Read | 0 = initial-repeater; 1 = initial-dual RS- 485; 2 = run-repeater; 3 = run-dual RS-485 | ||||
| HR | 0doc 0x0000 | DI-00_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 1doc 0x0001 | DI-01_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 2doc 0x0002 | DI-02_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 3doc 0x0003 | DI-03_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 4doc 0x0004 | DI-04_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 5doc 0x0005 | DI-05_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 6doc 0x0006 | DI-06_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 7doc 0x0007 | DI-07_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 8doc 0x0008 | DI-08_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 9doc 0x0009 | DI-09_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 10doc 0x000A | DI-10_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 11doc 0x000B | DI-11_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 12doc 0x000C | DI-12_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 13doc 0x000D | DI-13_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 14doc 0x000E | DI-14_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 15doc 0x000F | DI-15_mode | UINT16 | Read/write | 0 = DI; 1 = Counter | ||||
| HR | 32doc 0x0020 | DI-00_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 33doc 0x0021 | DI-01_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 34doc 0x0022 | DI-02_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 35doc 0x0023 | DI-03_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 36doc 0x0024 | DI-04_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 37doc 0x0025 | DI-05_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 38doc 0x0026 | DI-06_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 39doc 0x0027 | DI-07_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 40doc 0x0028 | DI-08_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 41doc 0x0029 | DI-09_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 42doc 0x002A | DI-10_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 43doc 0x002B | DI-11_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 44doc 0x002C | DI-12_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 45doc 0x002D | DI-13_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 46doc 0x002E | DI-14_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 47doc 0x002F | DI-15_filter | UINT16 | × 100 | µs | Read/write | |||
| HR | 64doc 0x0040 | DI-00_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 65doc 0x0041 | DI-01_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 66doc 0x0042 | DI-02_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 67doc 0x0043 | DI-03_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 68doc 0x0044 | DI-04_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 69doc 0x0045 | DI-05_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 70doc 0x0046 | DI-06_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 71doc 0x0047 | DI-07_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 72doc 0x0048 | DI-08_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 73doc 0x0049 | DI-09_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 74doc 0x004A | DI-10_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 75doc 0x004B | DI-11_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 76doc 0x004C | DI-12_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 77doc 0x004D | DI-13_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 78doc 0x004E | DI-14_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 79doc 0x004F | DI-15_counterEvent | UINT16 | Read/write | 0 = Rising Edge; 1 = Falling Edge; 2 = Both | ||||
| HR | 320doc 0x0140 | DO-00_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 321doc 0x0141 | DO-01_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 322doc 0x0142 | DO-02_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 323doc 0x0143 | DO-03_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 324doc 0x0144 | DO-04_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 325doc 0x0145 | DO-05_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 326doc 0x0146 | DO-06_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 327doc 0x0147 | DO-07_status | UINT16 | Read/write | 0 = OFF; 1 = ON | ||||
| HR | 352doc 0x0160 | DO-00_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 354doc 0x0162 | DO-01_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 356doc 0x0164 | DO-02_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 358doc 0x0166 | DO-03_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 360doc 0x0168 | DO-04_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 362doc 0x016A | DO-05_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 364doc 0x016C | DO-06_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 366doc 0x016E | DO-07_pulseCount | High word at this address, low word next. | UINT32 | ABCD | Read/write | |||
| HR | 416doc 0x01A0 | DO-00_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 417doc 0x01A1 | DO-01_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 418doc 0x01A2 | DO-02_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 419doc 0x01A3 | DO-03_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 420doc 0x01A4 | DO-04_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 421doc 0x01A5 | DO-05_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 422doc 0x01A6 | DO-06_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 423doc 0x01A7 | DO-07_pulseOnWidth | UINT16 | ms | Read/write | ||||
| HR | 448doc 0x01C0 | DO-00_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 449doc 0x01C1 | DO-01_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 450doc 0x01C2 | DO-02_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 451doc 0x01C3 | DO-03_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 452doc 0x01C4 | DO-04_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 453doc 0x01C5 | DO-05_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 454doc 0x01C6 | DO-06_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 455doc 0x01C7 | DO-07_pulseOffWidth | UINT16 | ms | Read/write | ||||
| HR | 480doc 0x01E0 | DO-00_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 481doc 0x01E1 | DO-01_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 482doc 0x01E2 | DO-02_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 483doc 0x01E3 | DO-03_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 484doc 0x01E4 | DO-04_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 485doc 0x01E5 | DO-05_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 486doc 0x01E6 | DO-06_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 487doc 0x01E7 | DO-07_safeModeStatus | UINT16 | Read/write | 0 = OFF; 1 = ON; 2 = Hold Last | ||||
| HR | 512doc 0x0200 | DO-00_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 513doc 0x0201 | DO-01_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 514doc 0x0202 | DO-02_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 515doc 0x0203 | DO-03_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 516doc 0x0204 | DO-04_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 517doc 0x0205 | DO-05_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 518doc 0x0206 | DO-06_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 519doc 0x0207 | DO-07_mode | UINT16 | Read/write | 0 = DO; 1 = Pulse | ||||
| HR | 30052doc 0x7564 | SYS_modbusWatchdogFuntion | UINT16 | Read/write | 0 = Disable; 1 = Enable | ||||
| HR | 30053doc 0x7565 | SYS_modbusWatchdogTimeout | UINT16 | s | Read/write | ||||
| HR | 30054doc 0x7566 | SYS_modbusWatchdogStatus | UINT16 | Read/write | 0 = Normal; 1 = Timeout | ||||
| HR | 30056doc 0x7568 | SYS_restartDevice | Write 404 to trigger. | UINT16 | Read/write | ||||
| HR | 30057doc 0x7569 | SYS_loadFactoryDefault | Write 404 to trigger. | UINT16 | Read/write | ||||
| HR | 30060doc 0x756C | SYS_port0Baudrate | UINT16 | Read/write | 1 = 1200; 2 = 2400; 3 = 4800; 4 = 9600; 5 = 19200; 6 = 38400; 7 = 57600; 8 = 115200; 9 = 921600 | ||||
| HR | 30061doc 0x756D | SYS_port1Baudrate | UINT16 | Read/write | 1 = 1200; 2 = 2400; 3 = 4800; 4 = 9600; 5 = 19200; 6 = 38400; 7 = 57600; 8 = 115200; 9 = 921600 | ||||
| HR | 30064doc 0x7570 | SYS_port0StopBit | UINT16 | Read/write | 0 = 1; 1 = 2 | ||||
| HR | 30065doc 0x7571 | SYS_port1StopBit | UINT16 | Read/write | 0 = 1; 1 = 2 | ||||
| HR | 30066doc 0x7572 | SYS_port0Parity | UINT16 | Read/write | 0 = None; 1 = Even; 2 = Odd | ||||
| HR | 30067doc 0x7573 | SYS_port1Parity | UINT16 | Read/write | 0 = None; 1 = Even; 2 = Odd |
Notes on this map
- Moxa does not appear to offer this manual on a public URL found in this pass; the link is an unaltered copy of the Moxa user's manual on a reseller's file host.
- Each table row gives the hex wire address, the 1-based decimal reference (e.g. 0x0000 = 40001; system registers use six digits, 0x7530 = 330001), access, size and function code.
- 32-bit counters are listed as ...High and ...Low word registers with the high word at the lower address; they are combined here as UINT32 high word first (ABCD).
- Left out: system strings and multi-word values whose format is not described (firmware version and release date, serial number, server name/location, password, vendor name).
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Moxa ioLogik R1212 RS-485 remote I/O
What Modbus registers does the Moxa ioLogik R1212 RS-485 remote I/O have?
This map lists 312 registers: 136 coils, 24 discrete inputs, 45 input registers, 107 holding registers. 243 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Moxa ioLogik R1212 RS-485 remote I/O Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Each row prints the hex protocol address and a 1-based reference number (0x0000 = 00001/10001/30001/40001). The hex address is sent on the wire; the table (coil, discrete input, input or holding) is set by the function code column.
What byte order does the Moxa ioLogik R1212 RS-485 remote I/O use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Moxa ioLogik R1212 RS-485 remote I/O?
Start with IR 30000 SYS_modelID (Model ID check); HR 30052 SYS_modbusWatchdogFuntion (Enable communication watchdog); HR 30053 SYS_modbusWatchdogTimeout (Watchdog timeout); DI 0 DI-00_status (First digital input); IR 32 DI-00_counterValue (First counter value); CO 320 DO-00_status (First output on/off).
How do I enable Modbus control of the Moxa ioLogik R1212 RS-485 remote I/O?
Set the device ID (1-99) on the two rotary dials. Put the Initial/Run switch on Initial to configure the unit at 9600 baud, no parity, 8 data bits, 1 stop bit (with ioSearch or the SYS_port* registers), then switch back to Run.
What happens when the Moxa ioLogik R1212 RS-485 remote I/O loses Modbus communication?
SYS_modbusWatchdogFuntion (0x7564) enables the host-connection watchdog, SYS_modbusWatchdogTimeout (0x7565) sets the timeout in seconds (factory default 10 s), SYS_modbusWatchdogStatus (0x7566) shows a timeout. It is disabled by default; safe-status settings only act when it is enabled.
Where is the official Moxa ioLogik R1212 RS-485 remote I/O Modbus documentation?
The source is ioLogik R1200 Series User's Manual (Edition 3.4), revision 2021-04. Moxa doesn't publish it on its own website, so this map was re-typed from a free copy at https://cdn11.bigcommerce.com/s-hltjsp5jm3/content/pdfs/moxa-iologik-r1200-series-manual.pdf. It may be an older revision, so check it against the live unit.
More Moxa Modbus register maps
- Sensor (remote I/O module)
Moxa ioLogik R1210 RS-485 remote I/O
ioLogik R1210 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1210, R1210, R1210-T - Sensor (remote I/O module)
Moxa ioLogik R1214 RS-485 remote I/O
ioLogik R1214 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1214, R1214, R1214-T - Sensor (remote I/O module)
Moxa ioLogik R1240 RS-485 remote I/O
ioLogik R1240 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1240, R1240, R1240-T - Sensor (remote I/O module)
Moxa ioLogik R1241 RS-485 remote I/O
ioLogik R1241 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1241, R1241, R1241-T
Other remote i/o modules register maps
- Sensor (remote I/O module, RTD inputs)
Seneca R-4RTD-8DIDO Ethernet I/O (4 RTD inputs, 8 digital I/O)
R-4RTD-8DIDO in the Series R I/O manual MI-00604-29-EN.
Also known as: R4RTD8DIDO, R-4RTD-8DIDO, Seneca R series 4RTD - Sensor (Ethernet data logger / I/O module)
Teracom TCW220 Ethernet data logger
TCW220 per the Teracom TCW220 user manual Revision R4.24, firmware V2.012 or later.
Also known as: TCW220 - Sensor (remote I/O module)
Unipi Technology Unipi Extension xS54 universal analog input module
Unipi Extension xS54 RS-485 module per the Unipi Extension xS54 Modbus map v2.0.
Also known as: Unipi Extension xS54, xS54 - Sensor (counter/frequency input module)
ICP DAS M-7080 / M-7080B 2-channel counter/frequency module (Modbus RTU)
ICP DAS M-7080 and M-7080B two-channel 32-bit counter/frequency modules with two digital outputs, in Modbus RTU mode.
Also known as: M-7080, M-7080B, M7080, M7080B - Sensor (RTD temperature input module)
Seneca Z-4RTD2-SI 4-channel RTD input module (Modbus RTU)
Z-4RTD2-SI per user manual MI00584-4-EN.
Also known as: Z-4RTD2, Z4RTD2-SI, Seneca Z-4RTD2-SI - Sensor (remote I/O module)
Unipi Technology Unipi Extension xS11 I/O module
Unipi Extension xS11 RS-485 module per the Unipi Extension xS11 Modbus map v2.0.
Also known as: Unipi Extension xS11, xS11
All remote i/o modules Modbus register maps →
Source: ioLogik R1200 Series User's Manual · Edition 3.4 · rev. 2021-04 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.