- Home
- Modbus register maps
- KEBA
- KeContact E10 smart energy meter (Modbus)
Energy meter · Modbus register map
KEBA KeContact E10 smart energy meter (Modbus) Modbus register map
Updated 17 November 2026
The KeContact E10 is KEBA's three-phase smart energy meter for home energy management with its wallboxes. It answers Modbus with holding registers only: instantaneous power, current, voltage, power factor and frequency, 64-bit energy counters per phase, a fast block for current/voltage/power, a plug-and-play identity block, a SunSpec common + meter (203) model, and a few configuration, identify and restart registers.
This page lists 184 Modbus registers for the KEBA KeContact E10 smart energy meter (Modbus) — 17 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from KEBA’s own free documentation (linked below) and checked against it.
- Manufacturer
- KEBA
- Model
- KeContact E10 smart energy meter (Modbus)
- Equipment type
- Energy meter
- Registers
- 184 (17 writable)
- Transport
- Modbus RTU, Modbus TCP
- Default unit ID
- Not stated
- Documented addressing
- 0-based (the number printed is the address on the wire)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- E10, KEBA E10, KeContact E10
Integration notes: KEBA KeContact E10 smart energy meter (Modbus)
Read the 64-bit energy counters at 512 (import) and 516 (export) and the per-phase power/current/voltage block 0-147, or use the SunSpec meter model at 40070 if your system speaks SunSpec. All values are big-endian, high word first.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 0 | Active power+ | UINT32 ABCD | Active power import (total) | Read |
| HR 2 | Active power- | UINT32 ABCD | Active power export (total) | Read |
| HR 60 | Current (L1) | UINT32 ABCD | Current L1 | Read |
| HR 62 | Voltage (L1) | UINT32 ABCD | Voltage L1 | Read |
| HR 26 | Supply frequency | UINT32 ABCD | Frequency | Read |
| HR 512 | Active energy+ | UINT64 ABCD | Active energy import | Read |
| HR 516 | Active energy- | UINT64 ABCD | Active energy export | Read |
Enable Modbus control & writes
Modbus RTU baud rate is set in register 258 (0 = 9600 ... 5 = 115200). IP address, subnet mask and DHCP are in registers 259-267 and take effect after a restart.
Byte order & addressing
- Read all registers of a multi-register value in one request.
- Writing 1 to register 268 locks all configuration and the restart register; plan the configuration first.
Network setup
- Registers 61613/61614 make the meter blink for identification on site.
Watch out for
- Power values are split into + (import) and - (export) registers, both unsigned, rather than one signed value.
KEBA KeContact E10 smart energy meter (Modbus) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0 | Active power+ | OBIS 1-0:1.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 2 | Active power- | OBIS 1-0:2.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 4 | Reactive power+ | OBIS 1-0:3.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 6 | Reactive power- | OBIS 1-0:4.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 16 | Apparent power+ | OBIS 1-0:9.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 18 | Apparent power- | OBIS 1-0:10.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 24 | Power factor | OBIS 1-0:13.4.0*255. | INT32 | ABCD | × 0.001 | Read | ||
| HR | 26 | Supply frequency | OBIS 1-0:14.4.0*255. | UINT32 | ABCD | × 0.001 | Hz | Read | |
| HR | 40 | Active power+ (L1) | OBIS 1-0:21.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 42 | Active power- (L1) | OBIS 1-0:22.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 44 | Reactive power+ (L1) | OBIS 1-0:23.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 46 | Reactive power- (L1) | OBIS 1-0:24.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 56 | Apparent power+ (L1) | OBIS 1-0:29.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 58 | Apparent power- (L1) | OBIS 1-0:30.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 60 | Current (L1) | OBIS 1-0:31.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 62 | Voltage (L1) | OBIS 1-0:32.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 64 | Power factor (L1) | OBIS 1-0:33.4.0*255. | INT32 | ABCD | × 0.001 | Read | ||
| HR | 80 | Active power+ (L2) | OBIS 1-0:41.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 82 | Active power- (L2) | OBIS 1-0:42.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 84 | Reactive power+ (L2) | OBIS 1-0:43.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 86 | Reactive power- (L2) | OBIS 1-0:44.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 96 | Apparent power+ (L2) | OBIS 1-0:49.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 98 | Apparent power- (L2) | OBIS 1-0:50.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 100 | Current (L2) | OBIS 1-0:51.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 102 | Voltage (L2) | OBIS 1-0:52.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 104 | Power factor (L2) | OBIS 1-0:53.4.0*255. | INT32 | ABCD | × 0.001 | Read | ||
| HR | 120 | Active power+ (L3) | OBIS 1-0:61.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 122 | Active power- (L3) | OBIS 1-0:62.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 124 | Reactive power+ (L3) | OBIS 1-0:63.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 126 | Reactive power- (L3) | OBIS 1-0:64.4.0*255. | UINT32 | ABCD | × 0.1 | var | Read | |
| HR | 136 | Apparent power+ (L3) | OBIS 1-0:69.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 138 | Apparent power- (L3) | OBIS 1-0:70.4.0*255. | UINT32 | ABCD | × 0.1 | VA | Read | |
| HR | 140 | Current (L3) | OBIS 1-0:71.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 142 | Voltage (L3) | OBIS 1-0:72.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 144 | Power factor (L3) | OBIS 1-0:73.4.0*255. | INT32 | ABCD | × 0.001 | Read | ||
| HR | 146 | Minimum active power+ * 3 | Three times the minimum active power+ (as named in the list). | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 256 | Measuring Interval | UINT16 | Read/write | 0 = 20 ms; 1 = 100 ms; 2 = 200 ms; 3 = 500 ms; 4 = 1000 ms | ||||
| HR | 257 | Current transformer type | UINT16 | Read/write | 0 = XH-SCT-10; 1 = XH-SCT-16; 2 = XH-SCT-24; 3 = EB103 | ||||
| HR | 258 | Modbus RTU baud rate | UINT16 | Read/write | 0 = 9600 Bd; 1 = 14400 Bd; 2 = 19200 Bd; 3 = 38400 Bd; 4 = 57600 Bd; 5 = 115200 Bd | ||||
| HR | 259 | Static IP Address octet 1 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 260 | Static IP Address octet 2 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 261 | Static IP Address octet 3 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 262 | Static IP Address octet 4 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 263 | Subnet Mask octet 1 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 264 | Subnet Mask octet 2 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 265 | Subnet Mask octet 3 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 266 | Subnet Mask octet 4 | One octet per register; active after restart. | UINT16 | Read/write | ||||
| HR | 267 | DHCP on/off | Active after restart. | UINT16 | Read/write | 0 = Disable DHCP; 1 = Enable DHCP | |||
| HR | 268 | Activate Read Only | Write 1 to lock all configuration and restart registers. | UINT16 | Read/write | ||||
| HR | 512 | Active energy+ | OBIS 1-0:1.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 516 | Active energy- | OBIS 1-0:2.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 520 | Reactive energy+ | OBIS 1-0:3.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 524 | Reactive energy- | OBIS 1-0:4.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 544 | Apparent energy+ | OBIS 1-0:9.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 548 | Apparent energy- | OBIS 1-0:10.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 592 | Active energy+ (L1) | OBIS 1-0:21.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 596 | Active energy- (L1) | OBIS 1-0:22.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 600 | Reactive energy+ (L1) | OBIS 1-0:23.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 604 | Reactive energy- (L1) | OBIS 1-0:24.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 624 | Apparent energy+ (L1) | OBIS 1-0:29.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 628 | Apparent energy- (L1) | OBIS 1-0:30.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 672 | Active energy+ (L2) | OBIS 1-0:41.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 676 | Active energy- (L2) | OBIS 1-0:42.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 680 | Reactive energy+ (L2) | OBIS 1-0:43.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 684 | Reactive energy- (L2) | OBIS 1-0:44.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 704 | Apparent energy+ (L2) | OBIS 1-0:49.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 708 | Apparent energy- (L2) | OBIS 1-0:50.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 752 | Active energy+ (L3) | OBIS 1-0:61.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 756 | Active energy- (L3) | OBIS 1-0:62.8.0*255. | UINT64 | ABCD | × 0.1 | Wh | Read | |
| HR | 760 | Reactive energy+ (L3) | OBIS 1-0:63.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 764 | Reactive energy- (L3) | OBIS 1-0:64.8.0*255. | UINT64 | ABCD | × 0.1 | varh | Read | |
| HR | 784 | Apparent energy+ (L3) | OBIS 1-0:69.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 788 | Apparent energy- (L3) | OBIS 1-0:70.8.0*255. | UINT64 | ABCD | × 0.1 | VAh | Read | |
| HR | 8192 | ManufacturerID | Fixed value 0x5233. | UINT16 | Read | ||||
| HR | 8193 | ProductID | Hardware type code (SU103/SU106 variants). | UINT16 | Read | 1 = SU103 R; 2 = SU103 L; 3 = SU103 LR; 17 = SU106 R; 18 = SU106 L; 19 = SU106 LR | |||
| HR | 8194 | ProductVersion | Hardware revision, e.g. 0x0103 = 1.3.x. | UINT16 | Read | ||||
| HR | 8195 | FirmwareVersion | Firmware revision, e.g. 0x0103 = 1.3.x. | UINT16 | Read | ||||
| HR | 8196 | VendorName | 32 characters, NUL padded. | STRING[32] | Read | ||||
| HR | 8212 | ProductName | 32 characters, NUL padded. | STRING[32] | Read | ||||
| HR | 8228 | SerialNumber | 32 characters, NUL padded. | STRING[32] | Read | ||||
| HR | 8244 | MeasuringInterval | Measuring interval in ms. | UINT16 | ms | Read | |||
| HR | 8245 | SubSwVersion | Patch level and release-candidate number. | UINT16 | Read | ||||
| HR | 40000 | C_SunSpec_ID | 0x53756E53 ('SunS') marks a SunSpec map. | UINT32 | ABCD | Read | |||
| HR | 40002 | C_SunSpec_DID | Common model: ID 1, length 66. | UINT16 | Read | ||||
| HR | 40003 | C_SunSpec_Length | Common model: ID 1, length 66. | UINT16 | Read | ||||
| HR | 40004 | C_Manufacturer | SunSpec common model text; 16 registers. | STRING[32] | Read | ||||
| HR | 40020 | C_Model | SunSpec common model text; 16 registers. | STRING[32] | Read | ||||
| HR | 40036 | C_Options | SunSpec common model text; 8 registers. | STRING[16] | Read | ||||
| HR | 40044 | C_Version | SunSpec common model text; 8 registers. | STRING[16] | Read | ||||
| HR | 40052 | C_SerialNumber | SunSpec common model text; 16 registers. | STRING[32] | Read | ||||
| HR | 40068 | C_DeviceAddress | Modbus unit ID. | UINT16 | Read | ||||
| HR | 40070 | C_SunSpec_DID | Meter model ID 203. | UINT16 | Read | ||||
| HR | 40071 | C_SunSpec_Length | Meter model length 105. | UINT16 | Read | ||||
| HR | 40072 | M_AC_Current | INT16 | × 10^SF (HR 40076) | A | Read | |||
| HR | 40073 | M_AC_Current_A | INT16 | × 10^SF (HR 40076) | A | Read | |||
| HR | 40074 | M_AC_Current_B | INT16 | × 10^SF (HR 40076) | A | Read | |||
| HR | 40075 | M_AC_Current_C | INT16 | × 10^SF (HR 40076) | A | Read | |||
| HR | 40076 | M_AC_Current_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40077 | M_AC_Voltage_LN | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40078 | M_AC_Voltage_AN | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40079 | M_AC_Voltage_BN | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40080 | M_AC_Voltage_CN | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40081 | M_AC_Voltage_LL | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40082 | M_AC_Voltage_AB | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40083 | M_AC_Voltage_BC | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40084 | M_AC_Voltage_CA | INT16 | × 10^SF (HR 40085) | V | Read | |||
| HR | 40085 | M_AC_Voltage_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40086 | M_AC_Freq | INT16 | × 10^SF (HR 40087) | Hz | Read | |||
| HR | 40087 | M_AC_Freq_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40088 | M_AC_Power | INT16 | × 10^SF (HR 40092) | W | Read | |||
| HR | 40089 | M_AC_Power_A | INT16 | × 10^SF (HR 40092) | W | Read | |||
| HR | 40090 | M_AC_Power_B | INT16 | × 10^SF (HR 40092) | W | Read | |||
| HR | 40091 | M_AC_Power_C | INT16 | × 10^SF (HR 40092) | W | Read | |||
| HR | 40092 | M_AC_Power_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40093 | M_AC_VA | INT16 | × 10^SF (HR 40097) | VA | Read | |||
| HR | 40094 | M_AC_VA_A | INT16 | × 10^SF (HR 40097) | VA | Read | |||
| HR | 40095 | M_AC_VA_B | INT16 | × 10^SF (HR 40097) | VA | Read | |||
| HR | 40096 | M_AC_VA_C | INT16 | × 10^SF (HR 40097) | VA | Read | |||
| HR | 40097 | M_AC_VA_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40098 | M_AC_VAR | INT16 | × 10^SF (HR 40102) | var | Read | |||
| HR | 40099 | M_AC_VAR_A | INT16 | × 10^SF (HR 40102) | var | Read | |||
| HR | 40100 | M_AC_VAR_B | INT16 | × 10^SF (HR 40102) | var | Read | |||
| HR | 40101 | M_AC_VAR_C | INT16 | × 10^SF (HR 40102) | var | Read | |||
| HR | 40102 | M_AC_VAR_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40103 | M_AC_PF | INT16 | × 10^SF (HR 40107) | % | Read | |||
| HR | 40104 | M_AC_PF_A | INT16 | × 10^SF (HR 40107) | % | Read | |||
| HR | 40105 | M_AC_PF_B | INT16 | × 10^SF (HR 40107) | % | Read | |||
| HR | 40106 | M_AC_PF_C | INT16 | × 10^SF (HR 40107) | % | Read | |||
| HR | 40107 | M_AC_PF_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40108 | M_Exported | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40110 | M_Exported_A | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40112 | M_Exported_B | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40114 | M_Exported_C | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40116 | M_Imported | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40118 | M_Imported_A | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40120 | M_Imported_B | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40122 | M_Imported_C | UINT32 | ABCD | × 10^SF (HR 40124) | Wh | Read | ||
| HR | 40124 | M_Energy_W_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40125 | M_Exported_VA | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40127 | M_Exported_VA_A | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40129 | M_Exported_VA_B | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40131 | M_Exported_VA_C | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40133 | M_Imported_VA | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40135 | M_Imported_VA_A | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40137 | M_Imported_VA_B | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40139 | M_Imported_VA_C | UINT32 | ABCD | × 10^SF (HR 40141) | VAh | Read | ||
| HR | 40141 | M_Energy_VA_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40142 | M_Import_VARh_Q1 | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40144 | M_Import_VARh_Q1A | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40146 | M_Import_VARh_Q1B | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40148 | M_Import_VARh_Q1C | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40150 | M_Import_VARh_Q2 | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40152 | M_Import_VARh_Q2A | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40154 | M_Import_VARh_Q2B | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40156 | M_Import_VARh_Q2C | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40158 | M_Export_VARh_Q3 | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40160 | M_Export_VARh_Q3A | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40162 | M_Export_VARh_Q3B | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40164 | M_Export_VARh_Q3C | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40166 | M_Export_VARh_Q4 | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40168 | M_Export_VARh_Q4A | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40170 | M_Export_VARh_Q4B | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40172 | M_Export_VARh_Q4C | UINT32 | ABCD | × 10^SF (HR 40174) | VARh | Read | ||
| HR | 40174 | M_Energy_VAR_SF | Power-of-ten scale factor for the related values. | INT16 | Read | ||||
| HR | 40175 | M_Events | UINT32 | ABCD | Read | ||||
| HR | 40177 | C_SunSpec_DID | End model marker (0xFFFF, length 0). | UINT16 | Read | ||||
| HR | 40178 | C_SunSpec_Length | End model marker (0xFFFF, length 0). | UINT16 | Read | ||||
| HR | 61440 | Active power+ (L1) (fast block) | OBIS 1-0:21.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61442 | Active power- (L1) (fast block) | OBIS 1-0:22.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61444 | Current (L1) (fast block) | OBIS 1-0:31.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 61446 | Voltage (L1) (fast block) | OBIS 1-0:32.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 61448 | Active power+ (L2) (fast block) | OBIS 1-0:41.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61450 | Active power- (L2) (fast block) | OBIS 1-0:42.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61452 | Current (L2) (fast block) | OBIS 1-0:51.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 61454 | Voltage (L2) (fast block) | OBIS 1-0:52.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 61456 | Active power+ (L3) (fast block) | OBIS 1-0:61.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61458 | Active power- (L3) (fast block) | OBIS 1-0:62.4.0*255. | UINT32 | ABCD | × 0.1 | W | Read | |
| HR | 61460 | Current (L3) (fast block) | OBIS 1-0:71.4.0*255. | UINT32 | ABCD | × 0.001 | A | Read | |
| HR | 61462 | Voltage (L3) (fast block) | OBIS 1-0:72.4.0*255. | UINT32 | ABCD | × 0.001 | V | Read | |
| HR | 61464 | Number of measurements (fast block) | Count of measurements taken. | UINT64 | ABCD | Read | |||
| HR | 61613 | Identify: blink frequency | 100-10000 mHz, default 1000. | UINT16 | mHz | Read/write | |||
| HR | 61614 | Identify: blink duration | Non-zero starts the identify blink, 0 stops it (0-600 s). | UINT16 | s | Read/write | |||
| HR | 61615 | Restart | Write 0x1 to restart the meter. | UINT16 | Write | ||||
| HR | 61616 | Start bootloader | Write 0xA0B1 to start the bootloader. | UINT16 | Write |
Notes on this map
- Multi-register values are most significant word first: the description sheet says the lower address holds the most significant bits and gives a uint32 example (0x0023 then 0x0044). 64-bit energy counters follow the same rule.
- Engineering values: power in 0.1 W/var/VA steps, current and voltage in 0.001 A/V, power factor in 0.001, frequency in 0.001 Hz, energy in 0.1 Wh/varh/VAh.
- SunSpec values use scale-factor registers that KEBA says can change at run time; always read the scale factor with the value.
- All data is read with function 03 (read holding registers); configuration registers accept 06 and 16.
- Static IP and subnet mask take one octet per register (4 registers each); network changes take effect after a restart (61615).
- In the SunSpec block the list shows 0x8000 (SunSpec 'not implemented') for total current 40072 and the average voltages 40077/40081, 0x8000 for the reactive-energy scale factor 40174, and 0 for the var-hour quadrant counters; use the per-phase values and the native energy counters instead.
- Reading an address that is not in the list returns exception 02. Reserved gaps are not listed.
- Bus settings other than the baud-rate code (register 258) are not given in the list, so defaults are left empty.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the KEBA KeContact E10 smart energy meter (Modbus)
What Modbus registers does the KEBA KeContact E10 smart energy meter (Modbus) have?
This map lists 184 registers: 184 holding registers. 17 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the KEBA KeContact E10 smart energy meter (Modbus) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 0-based (the number printed is the address on the wire). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The list gives start addresses, not register numbers: the first block starts at address 0 and the SunSpec block at 40000. The sheet itself warns that SunSpec register 40001 is read at address 40000.
What byte order does the KEBA KeContact E10 smart energy meter (Modbus) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the KEBA KeContact E10 smart energy meter (Modbus)?
Start with HR 0 Active power+ (Active power import (total)); HR 2 Active power- (Active power export (total)); HR 60 Current (L1) (Current L1); HR 62 Voltage (L1) (Voltage L1); HR 26 Supply frequency (Frequency); HR 512 Active energy+ (Active energy import); HR 516 Active energy- (Active energy export).
How do I enable Modbus control of the KEBA KeContact E10 smart energy meter (Modbus)?
Modbus RTU baud rate is set in register 258 (0 = 9600 ... 5 = 115200). IP address, subnet mask and DHCP are in registers 259-267 and take effect after a restart.
Where is the official KEBA KeContact E10 smart energy meter (Modbus) Modbus documentation?
The source is KeContact E10 - Modbus Register List (132941/00 v1.00), revision 2024-03, published free by KEBA at https://www.keba.com/download/x/052f09a75c/e10_modbus_register_list_v100.xlsx.
Other power & energy meters register maps
- Energy meter
Legrand Energy meter 4 120 68 (RS-485 Modbus)
Legrand energy meter cat. no. 4 120 68 with RS-485 Modbus RTU, per Modbus table F02230EN-01.
Also known as: 412068, 4 120 68, Legrand 412068 - Energy meter (DIN-rail, single-phase, MID)
Lumel NMID08 / NMID09 / NMID10 single-phase energy meter
Modbus RTU versions of the NMID08 (1/5 A CT), NMID09 (100 mA CT) and NMID10 (100 A direct) meters; the LITE and MBUS versions have no Modbus port.
Also known as: NMID08, NMID09, NMID10 - Energy meter
Northern Design Cube 300 panel kWh meter (Modbus RTU option)
Cube300 meters fitted with the RS-485 Modbus option, per the October 2005 Modbus Communications manual.
Also known as: Cube300, ND Cube 300, Northern Design Cube300 - Energy meter (multi-circuit power monitor)
Panasonic KW9M Eco-POWER METER
Panasonic KW9M (AKW91110) with the Modbus RTU protocol selected, user manual WUME-KW9M-10.
Also known as: AKW91110 - Energy meter
Rishabh Instruments RISH Delta Energy NX multifunction energy meter
Rishabh RISH Delta Energy NX panel energy meters with RS-485 Modbus RTU, per the operating manual on the product page (standard CT version).
Also known as: RISH Delta Energy NX, Delta Energy NX, RISH Delta Energy - Energy meter
Rishabh Instruments RISH EM 1320 / 1330 / 1340 / 2340 programmable energy meters
Rishabh RISH EM 1320/1330/1340 and EM 2320/2330/2340 panel energy meters with RS-485 Modbus, per interface definition DMAN-00IM-0721 Rev. B (06/2020). Rows marked 'only 2340' apply to the dual-source EM 2340.
Also known as: RISH EM 1320, RISH EM 1330, RISH EM 1340, RISH EM 2320, RISH EM 2330, RISH EM 2340, EM2340DS
All power & energy meters Modbus register maps →
Source: KeContact E10 - Modbus Register List · 132941/00 v1.00 · rev. 2024-03. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.