- Home
- Modbus register maps
- Laumas
- WLIGHT weight indicator / transmitter (Modbus RTU)
Sensor (load-cell weight indicator) · Modbus register map
Laumas WLIGHT weight indicator / transmitter (Modbus RTU) Modbus register map
Updated 17 November 2026
The WLIGHT is a compact load-cell weight indicator with RS-485. In Modbus RTU mode it offers a small register set: identification, a command register, a status word, gross/net/peak weight as 32-bit pairs, the division and unit setting, and the sample weight used for calibration.
This page lists 12 Modbus registers for the Laumas WLIGHT weight indicator / transmitter (Modbus RTU) — 2 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Laumas’s own free documentation (linked below) and checked against it.
- Manufacturer
- Laumas
- Model
- WLIGHT weight indicator / transmitter (Modbus RTU)
- Equipment type
- Sensor (load-cell weight indicator)
- Registers
- 12 (2 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- WLIGHT, W LIGHT
Integration notes: Laumas WLIGHT weight indicator / transmitter (Modbus RTU)
Choose Modbus RTU in the serial menu, then read 40007-40013 with FC3 for status, gross, net and peak weight. Apply the sign bits and the division index. Write 7, 9 or 8 to 40006 for tare on, tare off and zero.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 6 | Status register | BITMAP16 | Status word | Read |
| HR 7 | Gross weight | UINT32 ABCD | Gross weight | Read |
| HR 9 | Net weight | UINT32 ABCD | Net weight | Read |
| HR 13 | Divisions and units of measure | UINT16 | Division index for decimals | Read |
| HR 5 | Command register | UINT16 | Command register | Read/write |
Enable Modbus control & writes
Serial communication is disabled by default: select the Modbus RTU protocol in the serial menu, then address (1-99, default 1), baud (default 9600), parity (default none), stop bits (default 1).
Byte order & addressing
- Only FC3 and FC16 are supported.
- Maximum 32 registers per request.
Network setup
- Broadcast writes (address 0) are executed without reply; broadcast reads are ignored.
Watch out for
- Command 99 writes EEPROM, which allows about 100000 writes.
Laumas WLIGHT weight indicator / transmitter (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 40001 | Firmware version | UINT16 | Read | |||||
| HR | 1doc 40002 | Instrument type | UINT16 | Read | |||||
| HR | 2doc 40003 | Year of manufacture | UINT16 | Read | |||||
| HR | 3doc 40004 | Serial number | UINT16 | Read | |||||
| HR | 4doc 40005 | Active program | UINT16 | Read | |||||
| HR | 5doc 40006 | Command register | Write a command code to run it. | UINT16 | Read/write | 0 = No command; 7 = Semi-automatic tare on (net display); 8 = Semi-automatic zero; 9 = Semi-automatic tare off (gross display); 21 = Keypad lock; 22 = Keypad and display unlock; 23 = Keypad and display lock; 99 = Save data in EEPROM; 100 = Tare weight zero setting for calibration; 101 = Sample weight storage for calibration | |||
| HR | 6doc 40007 | Status register | Weight sign, stability and error flags. | BITMAP16 | Read | bit 0 = Load cell error; bit 1 = AD converter malfunction; bit 2 = Maximum weight exceeded by 9 divisions; bit 3 = Gross weight over 110% of full scale; bit 4 = Gross weight over 999999 or under -999999; bit 5 = Net weight over 999999 or under -999999; bit 7 = Gross weight negative sign; bit 8 = Net weight negative sign; bit 9 = Peak weight negative sign; bit 10 = Net display mode; bit 11 = Weight stable; bit 12 = Weight within +/- 1/4 division of zero | |||
| HR | 7doc 40008 | Gross weight | Magnitude without decimal point; sign is status bit 7. | UINT32 | ABCD | Read | |||
| HR | 9doc 40010 | Net weight | Magnitude without decimal point; sign is status bit 8. | UINT32 | ABCD | Read | |||
| HR | 11doc 40012 | Peak weight | Magnitude without decimal point; sign is status bit 9. | UINT32 | ABCD | Read | |||
| HR | 13doc 40014 | Divisions and units of measure | High byte = unit index, low byte = division index. | UINT16 | Read | ||||
| HR | 64doc 40065 | Sample weight for calibration | Test weight in divisions; use with command 101. Reads 0 after success. | INT32 | ABCD | Read/write |
Notes on this map
- Host: this copy is hosted by Massload, not by Laumas; no public copy was found on laumas.com.
- Word order: H/L pairs with high word first; the read example returns gross 4000 as 0x0000 0x0FA0 and the -56 calibration example is 0xFFFF 0xFFC8, so ABCD is documented.
- Weights are unsigned magnitudes without decimal point; the sign is in status bits 7-9. Divisions/units register 40014: low byte = division index (0-18: 100, 50, 20, 10, 5, 2, 1 with 0 decimals; 0.5, 0.2, 0.1 with 1; 0.05, 0.02, 0.01 with 2; 0.005, 0.002, 0.001 with 3; 0.0005, 0.0002, 0.0001 with 4); high byte = unit index (0 kg, 1 g, 2 t, 3 lb, 4 N, 5 l, 6 bar, 7 atm, 8 pieces, 9 N m, 10 kg m, 11 other).
- Command codes 1, 6, 20 and 98 are printed with names in display symbols that do not extract and are left out; 10-18 are reserved.
- The manual's write example targets 40037-40038, which are not in this model's register list; treat it as a generic framing example.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Laumas WLIGHT weight indicator / transmitter (Modbus RTU)
What Modbus registers does the Laumas WLIGHT weight indicator / transmitter (Modbus RTU) have?
This map lists 12 registers: 12 holding registers. 2 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Laumas WLIGHT weight indicator / transmitter (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed 40001-40066; subtract 40001 for a 0-based client (the manual's own example: 40028 -> 27). The read example uses start address 0x0007 for gross weight at 40008.
What byte order does the Laumas WLIGHT weight indicator / transmitter (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Laumas WLIGHT weight indicator / transmitter (Modbus RTU)?
Start with HR 6 Status register (Status word); HR 7 Gross weight (Gross weight); HR 9 Net weight (Net weight); HR 13 Divisions and units of measure (Division index for decimals); HR 5 Command register (Command register).
How do I enable Modbus control of the Laumas WLIGHT weight indicator / transmitter (Modbus RTU)?
Serial communication is disabled by default: select the Modbus RTU protocol in the serial menu, then address (1-99, default 1), baud (default 9600), parity (default none), stop bits (default 1).
Where is the official Laumas WLIGHT weight indicator / transmitter (Modbus RTU) Modbus documentation?
The source is WLIGHT Installation and User Manual (version 1.03). Laumas doesn't publish it on its own website, so this map was re-typed from a free copy at https://www.massload.com/wp-content/uploads/2026/07/Laumas-WLIGHT_UserManual.pdf. It may be an older revision, so check it against the live unit.
More Laumas Modbus register maps
- Sensor (load-cell weight transmitter)
Laumas TLB4 four-channel weight transmitter (Modbus RTU / Modbus TCP)
Laumas TLB4 with the Modbus RTU port or the Modbus/TCP option; communication protocols manual version 1.12. Direct registers only.
Also known as: TLB4, TLB4 MODBUS, TLB4 Modbus/TCP - Sensor (load-cell weight transmitter)
Laumas TLS weight transmitter with analog output (Modbus RTU)
Laumas TLS weight transmitter / indicator with RS-485, installation and user manual version 1.19.
Also known as: TLS, TLS 4-20mA, TLS 0-10V, CASTLTASTATEX
Other valves, actuators & sensors register maps
- Sensor (CO2, humidity, temperature module)
Sensirion SCD30 CO2, humidity and temperature sensor module
Sensirion SCD30 sensor module with the SEL pin pulled high at power-up (Modbus mode), per interface description version 1.0.
Also known as: SCD30 - Sensor (flow transmitter)
Siemens SITRANS F C MASS 6000 with USM II Modbus RTU module
SITRANS F C MASS 6000 Coriolis flow transmitters fitted with the USM II Modbus RTU RS-485 add-on module (operating instructions 03/2021).
Also known as: MASS 6000, SITRANS FC MASS 6000 - Sensor (relay output module)
Teracom TDO340 4-channel Modbus RTU relay output module
TDO340 per the Teracom TDO340 user manual Revision R1.2, firmware V1.03 or later.
Also known as: TDO340 - Sensor (AC/DC voltage transducer)
Teracom TSV300 AC/DC voltage transducer with Modbus RTU
TSV300 per the Teracom TSV300 user manual Revision R1.4, firmware V1.06 or later.
Also known as: TSV300 - Sensor (CO2 probe)
Vaisala GMP252 CARBOCAP carbon dioxide probe (Modbus RTU)
GMP252 probe in Modbus RTU mode, user guide M211897EN-G.
Also known as: GMP252, CARBOCAP GMP252, Vaisala GMP252 - Sensor (H2O2 probe)
Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)
HPP271 vaporized hydrogen peroxide probe, Modbus RTU interface (user guide M211888EN-E).
Also known as: HPP271, PEROXCAP HPP271
All valves, actuators & sensors Modbus register maps →
Source: WLIGHT Installation and User Manual · version 1.03 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.