Easy Modbus
  1. Home
  2. Modbus register maps
  3. Vaisala
  4. HPP271 hydrogen peroxide probe (Modbus RTU)

Sensor (H2O2 probe) · Modbus register map

Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) Modbus register map

Updated 19 November 2026

Short answer

The HPP271 is a Vaisala PEROXCAP probe for vaporized hydrogen peroxide. It is a Modbus RTU slave on RS-485. This map covers H2O2 concentration, H2O+H2O2 dew point and water concentration, status codes, sensor vitality, pressure compensation, purge, low-H2O2 threshold and analog-output settings.

This page lists 44 Modbus registers for the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) — 28 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Vaisala’s own free documentation (linked below) and checked against it.

Manufacturer
Vaisala
Model
HPP271 hydrogen peroxide probe (Modbus RTU)
Equipment type
Sensor (H2O2 probe)
Registers
44 (28 writable)
Transport
Modbus RTU
Default unit ID
240
Default serial
19200 baud, 8N2
Documented addressing
1-based (subtract 1 for the wire address)
32-bit word order
CDAB low word first (word-swapped)
Also known as
HPP271, PEROXCAP HPP271
Source document
HPP271 User Guide · M211888EN-E · rev. 2023-04
Download CSV all columns JSON Manufacturer PDF ↗

Integration notes: Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)

Integration in brief

Read holding registers 1-16 for H2O2, dew point and water concentration (CDAB floats); check 513 and 529 for reading validity.

Minimum registers to map

Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.

RegisterNameTypeWhyAccess
HR 0H2O2 concentration by volumeFLOAT32 CDABH2O2 ppmRead
HR 10H2O+H2O2 dew pointFLOAT32 CDABH2O+H2O2 dew pointRead
HR 512Device statusBITMAP16Device statusRead
HR 528H2O2 concentration statusBITMAP16H2O2 reading statusRead
HR 546Sensor vitalityFLOAT32 CDABSensor vitalityRead

Enable Modbus control & writes

Digital (RS-485 Modbus) or analog output is chosen at power-up by pin 5 of the M12 connector: leave pin 5 floating for Modbus, tie it to ground for analog. Power-cycle after changing it.

Byte order & addressing

Network setup

Watch out for

Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) Modbus registers

Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.

44 of 44 shown
Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) Modbus register map
TableAddressNameDescriptionTypeOrderScaleUnitsAccessValues / bits
HR0doc 1H2O2 concentration by volumeFLOAT32CDABppmRead
HR10doc 11H2O+H2O2 dew pointFLOAT32CDAB°CRead
HR14doc 15Water concentration by volumeFLOAT32CDABppmRead
HR256doc 257H2O2 concentration (integer)INT16ppmRead
HR261doc 262H2O+H2O2 dew point (integer)INT16× 0.01°CRead
HR263doc 264Water concentration (integer)INT16ppmRead
HR512doc 513Device status0 = OK.BITMAP16Readbit 0 = Critical error, maintenance needed; bit 1 = Error, may recover automatically; bit 2 = Warning; bit 3 = Notification; bit 4 = Calibration enabled
HR513doc 514Status code lowSum of active codes.UINT32CDABReadbit 0 = Firmware checksum mismatch; bit 1 = Device settings corrupted; bit 3 = Supply voltage too high; bit 4 = Internal voltage too low; bit 5 = Internal voltage too high; bit 6 = Humidity sensor failure (open circuit); bit 10 = Humidity sensor failure (open circuit); bit 14 = Temperature sensor failure (open circuit); bit 15 = Temperature sensor failure (short circuit); bit 18 = Temperature sensor failure (open circuit); bit 19 = Temperature sensor failure (short circuit)
HR515doc 516Status code highSum of active codes.UINT32CDABReadbit 8 = A/D converter failure (external); bit 9 = Non-volatile memory failure; bit 12 = Humidity sensor failure (short circuit); bit 13 = Purge in progress; bit 14 = A/D converter failure (internal); bit 15 = Calibration about to expire; bit 16 = Calibration expired
HR528doc 529H2O2 concentration status0 = OK.BITMAP16Readbit 1 = Not reliable; bit 5 = Locked during purge; bit 6 = Calibration expired; bit 7 = Sensor failure; bit 8 = Not ready
HR533doc 534Dew point statusBITMAP16Readbit 1 = Not reliable; bit 5 = Locked during purge; bit 6 = Calibration expired; bit 7 = Sensor failure; bit 8 = Not ready
HR535doc 536Water concentration statusBITMAP16Readbit 1 = Not reliable; bit 5 = Locked during purge; bit 6 = Calibration expired; bit 7 = Sensor failure; bit 8 = Not ready
HR546doc 547Sensor vitality1-100 %; 100 = new sensor. In demanding use, Vaisala advises service at 40 %.FLOAT32CDAB%Read
HR768doc 769Volatile pressure compensation813.25-1213.25; cleared at reset.FLOAT32CDABhPaRead/write
HR772doc 773Power-up pressure compensationDefault 1013.25.FLOAT32CDABhPaRead/write
HR776doc 777Purge interval60-10080, default 1440.INT16minRead/write
HR778doc 779Measurement filtering factor0.01-1; 1 = off. H2O2 only.FLOAT32CDABRead/write
HR782doc 783Low H2O2 threshold on/offUINT16Read/write0 = Off; 1 = On
HR784doc 785Low H2O2 threshold activation levelDefault 3.FLOAT32CDABppmRead/write
HR786doc 787Low H2O2 threshold activation delayDefault 1800.INT32CDABsRead/write
HR788doc 789Low H2O2 threshold deactivation levelDefault 10.FLOAT32CDABppmRead/write
HR790doc 791Low H2O2 threshold deactivation delayDefault 10.INT32CDABsRead/write
HR1282doc 1283Purge status / manual startWrite 1 to start; reads 1-100 progress, 0 done, -1 failed.INT16Read/write
HR1284doc 1285Pressure compensation on/offUINT16Read/write0 = Off; 1 = On
HR1286doc 1287Manual purge trigger in analog modeUINT16Read/write0 = Off; 1 = On
HR1287doc 1288Allow interval purge during H2O2 exposureUINT16Read/write0 = Off; 1 = On
HR1536doc 1537Modbus address1-255, default 240.INT16Read/write
HR1537doc 1538Bit rateUINT16Read/write5 = 9600; 6 = 19200; 7 = 38400; 8 = 57600; 9 = 115200
HR1538doc 1539Parity, data, stop bitsDefault 1 (None, 8, 2).UINT16Read/write0 = None, 8, 1; 1 = None, 8, 2; 2 = Even, 8, 1; 3 = Even, 8, 2; 4 = Odd, 8, 1; 5 = Odd, 8, 2
HR1539doc 1540Response delayExtra delay 0-1000 ms.INT16msRead/write
HR1540doc 1541Restart deviceWrite 1 to restart.INT16Write
HR1792doc 1793AOUT1 output modeUINT16Read/write0 = Off; 2 = 4-20 mA
HR1793doc 1794AOUT1 output parameterAddress 0x0000, 0x000A or 0x000E.UINT16Read/write
HR1794doc 1795AOUT1 scale low endFLOAT32CDABRead/write
HR1796doc 1797AOUT1 scale high endFLOAT32CDABRead/write
HR1798doc 1799AOUT1 error output0-25 mA.FLOAT32CDABmARead/write
HR2048doc 2049AOUT2 output modeUINT16Read/write0 = Off; 2 = 4-20 mA
HR2049doc 2050AOUT2 output parameterAddress 0x0000, 0x000A or 0x000E.UINT16Read/write
HR2050doc 2051AOUT2 scale low endFLOAT32CDABRead/write
HR2052doc 2053AOUT2 scale high endFLOAT32CDABRead/write
HR2054doc 2055AOUT2 error output0-25 mA.FLOAT32CDABmARead/write
HR7936doc 7937Signed integer testAlways reads -12345.INT16Read
HR7937doc 7938Floating point testAlways reads -123.45.FLOAT32CDABRead
HR7939doc 7940Text string testReads the text "-123.45".STRING[8]Read

Notes on this map

Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.

Questions about the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)

What Modbus registers does the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) have?

This map lists 44 registers: 44 holding registers. 28 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.

Are the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) Modbus addresses 0-based or 1-based?

The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The guide numbers registers in decimal starting at 1 and also prints the 0-based hex address used in the request; register number 1 is address 0x0000 on the wire.

What byte order does the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) use for 32-bit values?

Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.

What are the minimum Modbus registers to integrate the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)?

Start with HR 0 H2O2 concentration by volume (H2O2 ppm); HR 10 H2O+H2O2 dew point (H2O+H2O2 dew point); HR 512 Device status (Device status); HR 528 H2O2 concentration status (H2O2 reading status); HR 546 Sensor vitality (Sensor vitality).

How do I enable Modbus control of the Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)?

Digital (RS-485 Modbus) or analog output is chosen at power-up by pin 5 of the M12 connector: leave pin 5 floating for Modbus, tie it to ground for analog. Power-cycle after changing it.

Where is the official Vaisala HPP271 hydrogen peroxide probe (Modbus RTU) Modbus documentation?

The source is HPP271 User Guide (M211888EN-E), revision 2023-04, published free by Vaisala at https://docs.vaisala.com/r/M211888EN-E/en-US.

More Vaisala Modbus register maps

Other valves, actuators & sensors register maps

All valves, actuators & sensors Modbus register maps →

Source: HPP271 User Guide · M211888EN-E · rev. 2023-04. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.