- Home
- Modbus register maps
- Vaisala
- MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)
Sensor (transformer oil monitor) · Modbus register map
Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) Modbus register map
Updated 19 November 2026
The MHT410 is a Vaisala transmitter mounted on a power transformer that measures hydrogen and moisture dissolved in the oil plus oil temperature. Its RS-485 line runs Modbus RTU by default. This map covers H2 averages and rate-of-change values, oil moisture values and temperature in float and integer form, and the device status bits.
This page lists 25 Modbus registers for the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) — 0 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Vaisala’s own free documentation (linked below) and checked against it.
- Manufacturer
- Vaisala
- Model
- MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)
- Equipment type
- Sensor (transformer oil monitor)
- Registers
- 25 (0 writable)
- Transport
- Modbus RTU
- Default unit ID
- 240
- Default serial
- 19200 baud, 8N1
- Documented addressing
- 1-based (subtract 1 for the wire address)
- 32-bit word order
- CDAB low word first (word-swapped)
- Also known as
- MHT410
- Source document
- MHT410 User Guide · M211737EN-J · rev. 2023-11
Integration notes: Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)
Read holding registers 1-28 in one request (CDAB floats) for all H2, moisture and temperature values, and 513 for status and the H2 alarm bit.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 0 | H2 1 hour average | FLOAT32 CDAB | H2 1 h average | Read |
| HR 2 | H2 24 hour average | FLOAT32 CDAB | H2 24 h average | Read |
| HR 16 | Oil moisture current | FLOAT32 CDAB | Oil moisture ppm | Read |
| HR 26 | Oil temperature | FLOAT32 CDAB | Oil temperature | Read |
| HR 512 | Device status bits | BITMAP16 | Device status | Read |
Enable Modbus control & writes
The RS-485 line on the screw terminals is in Modbus mode from the factory. Serial settings and the protocol (Modbus, DNP3 or Vaisala Industrial Protocol) are changed with serial commands over the service port.
Byte order & addressing
- Floats are low word first (CDAB); pick "word-swapped" float in masters that default to high word first.
- Read each 32-bit value in one transaction.
Network setup
- Defaults: address 240, 19200 baud, no parity, 8 data bits, 1 stop bit.
- For Modbus the bit rate must be 9600-57600 and parity must be none.
Watch out for
- Leave at least 1 second between Modbus requests.
Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 1 | H2 1 hour average | Hydrogen dissolved in oil. | FLOAT32 | CDAB | ppmv | Read | ||
| HR | 2doc 3 | H2 24 hour average | FLOAT32 | CDAB | ppmv | Read | |||
| HR | 4doc 5 | H2 daily rate of change | FLOAT32 | CDAB | ppmv | Read | |||
| HR | 6doc 7 | H2 weekly rate of change | FLOAT32 | CDAB | ppmv | Read | |||
| HR | 8doc 9 | H2 monthly rate of change | FLOAT32 | CDAB | ppmv | Read | |||
| HR | 14doc 15 | Oil moisture relative saturation | FLOAT32 | CDAB | %RS | Read | |||
| HR | 16doc 17 | Oil moisture current | FLOAT32 | CDAB | ppmw | Read | |||
| HR | 18doc 19 | Oil moisture 24 h average | FLOAT32 | CDAB | ppmw | Read | |||
| HR | 20doc 21 | Oil moisture daily rate of change | FLOAT32 | CDAB | ppmw | Read | |||
| HR | 22doc 23 | Oil moisture weekly rate of change | FLOAT32 | CDAB | ppmw | Read | |||
| HR | 24doc 25 | Oil moisture monthly rate of change | FLOAT32 | CDAB | ppmw | Read | |||
| HR | 26doc 27 | Oil temperature | FLOAT32 | CDAB | °C | Read | |||
| HR | 256doc 257 | H2 1 h average (integer) | INT16 | ppmv | Read | ||||
| HR | 257doc 258 | H2 24 h average (integer) | INT16 | ppmv | Read | ||||
| HR | 258doc 259 | H2 daily ROC (integer) | INT16 | ppmv | Read | ||||
| HR | 259doc 260 | H2 weekly ROC (integer) | INT16 | ppmv | Read | ||||
| HR | 260doc 261 | H2 monthly ROC (integer) | INT16 | ppmv | Read | ||||
| HR | 263doc 264 | Oil relative saturation (integer) | INT16 | × 0.1 | %RS | Read | |||
| HR | 264doc 265 | Oil moisture current (integer) | INT16 | × 0.1 | ppmw | Read | |||
| HR | 265doc 266 | Oil moisture 24 h average (integer) | INT16 | × 0.1 | ppmw | Read | |||
| HR | 266doc 267 | Oil moisture daily ROC (integer) | INT16 | × 0.1 | ppmw | Read | |||
| HR | 267doc 268 | Oil moisture weekly ROC (integer) | INT16 | × 0.1 | ppmw | Read | |||
| HR | 268doc 269 | Oil moisture monthly ROC (integer) | INT16 | × 0.1 | ppmw | Read | |||
| HR | 269doc 270 | Oil temperature (integer) | INT16 | × 0.1 | °C | Read | |||
| HR | 512doc 513 | Device status bits | 0 = OK; values add up. | BITMAP16 | Read | bit 0 = Critical error (maintenance needed); bit 1 = Error (may recover); bit 2 = RH measurement error; bit 3 = T measurement error; bit 4 = H2 measurement error; bit 5 = Other error; bit 6 = H2 alarm level exceeded |
Notes on this map
- All registers are holding registers read with function 03; the device lists no write function, so it is read-only over Modbus.
- 32-bit floats put the least significant word at the listed register (CDAB); the guide states this and labels each pair LSW then MSW.
- Unavailable data reads as quiet NaN (float) or 0x8000 (16-bit integer) rather than an exception.
- Serial settings are changed with Vaisala Industrial Protocol serial commands (service port), not over Modbus.
- Integer moisture and temperature registers carry one decimal (raw x 0.1); integer H2 values are whole ppm.
- Registers 11-14 and 262-263 are not used in the published table.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)
What Modbus registers does the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) have?
This map lists 25 registers: 25 holding registers. 0 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The guide numbers registers in decimal starting at 1 and also prints the 0-based hex address used in the request; register number 1 is address 0x0000 on the wire.
What byte order does the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)?
Start with HR 0 H2 1 hour average (H2 1 h average); HR 2 H2 24 hour average (H2 24 h average); HR 16 Oil moisture current (Oil moisture ppm); HR 26 Oil temperature (Oil temperature); HR 512 Device status bits (Device status).
How do I enable Modbus control of the Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)?
The RS-485 line on the screw terminals is in Modbus mode from the factory. Serial settings and the protocol (Modbus, DNP3 or Vaisala Industrial Protocol) are changed with serial commands over the service port.
Where is the official Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU) Modbus documentation?
The source is MHT410 User Guide (M211737EN-J), revision 2023-11, published free by Vaisala at https://docs.vaisala.com/r/M211737EN-J/en-US.
More Vaisala Modbus register maps
- Sensor (dew point probe)
Vaisala DMP Series dew point probes (DMP5, DMP6, DMP7, DMP8) (Modbus RTU)
Vaisala DMP5, DMP6, DMP7 and DMP8 dew point and temperature probes, Modbus RTU interface (user guide M212357EN-F).
Also known as: DMP5, DMP6, DMP7, DMP8, DRYCAP DMP series - Sensor (dew point transmitter)
Vaisala DMT143 miniature dew point transmitter (Modbus RTU)
DMT143 dew point transmitters ordered with the Modbus RTU option (user guide M211435EN-L).
Also known as: DMT143, DRYCAP DMT143 - Sensor (dew point transmitter)
Vaisala DMT153 dew point transmitter (Modbus RTU)
DMT153 trace-moisture dew point transmitter, Modbus RTU interface (user guide M213149EN-B).
Also known as: DMT153, DRYCAP DMT153 - Sensor (CO2 duct transmitter)
Vaisala GMD110 duct CO2 transmitter (Modbus RTU)
GMD110 duct-mount CO2 transmitter, Modbus RTU interface (user guide M212885EN-B).
Also known as: GMD110, CARBOCAP GMD110 - Sensor (CO2 probe)
Vaisala GMP251 CARBOCAP carbon dioxide probe (Modbus RTU)
GMP251 probe in Modbus RTU mode, user guide M211799EN-N.
Also known as: GMP251, CARBOCAP GMP251, Vaisala GMP251 - Sensor (CO2 probe)
Vaisala GMP252 CARBOCAP carbon dioxide probe (Modbus RTU)
GMP252 probe in Modbus RTU mode, user guide M211897EN-G.
Also known as: GMP252, CARBOCAP GMP252, Vaisala GMP252 - Sensor (CO2 wall transmitter)
Vaisala GMW87 CO2 and temperature wall transmitter (Modbus RTU)
GMW87, the RS-485 Modbus RTU model of the GMW80 series (user guide M211748EN-H).
Also known as: GMW87, GMW80 series Modbus - Sensor (humidity and temperature transmitter)
Vaisala HMDW110 series humidity and temperature transmitters with TMI110 (Modbus RTU)
HMDW110-series duct, wall and outdoor transmitters and TMI110 ordered with the Modbus RTU option (user guide M211726EN-L).
Also known as: HMD110, HMD112, HMW110, HMW112, HMW112D, HMS110, HMS112, TMW110, TMW112, TMW112D, TMI110 - Sensor (humidity and temperature module)
Vaisala HMM170 humidity module (Modbus RTU)
HMM170 OEM humidity and temperature module with the Modbus RTU interface (user guide M212259EN-D).
Also known as: HMM170, HUMICAP HMM170 - Sensor (humidity and temperature probe)
Vaisala HMP Series (HMP1-HMP9) with MMP8 and TMP1 probes (Modbus RTU)
Vaisala HMP1/3/4/5/7/8/9, TMP1 and MMP8 probes with the Modbus RTU interface (user guide M212022EN-M).
Also known as: HMP1, HMP3, HMP4, HMP5, HMP7, HMP8, HMP9, TMP1, MMP8 - Sensor (humidity and temperature probe)
Vaisala HMP60 / HMP110 series humidity and temperature probes (Modbus RTU)
HMP60/HMP110-series probes ordered with the Modbus RTU option (user guide M211060EN-N).
Also known as: HMP110, HMP113, HMP115, TMP115, HMP60, HMP63, HUMICAP HMP110, HMP110T, HMP63T, HMP115T - Sensor (humidity and temperature transmitter)
Vaisala HMW87 / HMW87D wall humidity and temperature transmitters (Modbus RTU)
HMW87 and HMW87D wall transmitters of the HMDW80 series (the Modbus models in user guide M211510EN-J).
Also known as: HMW87, HMW87D, HMDW80 Modbus - Sensor (H2O2 probe)
Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)
HPP271 vaporized hydrogen peroxide probe, Modbus RTU interface (user guide M211888EN-E).
Also known as: HPP271, PEROXCAP HPP271 - Sensor (H2O2 / humidity probe)
Vaisala HPP272 hydrogen peroxide, humidity and temperature probe (Modbus RTU)
HPP272 vaporized hydrogen peroxide probe, Modbus RTU interface (user guide M211972EN-G).
Also known as: HPP272, PEROXCAP HPP272 - Sensor transmitter (host for Vaisala probes)
Vaisala Indigo510 / Indigo520 transmitters (Modbus TCP)
Indigo510 and Indigo520 transmitter registers (unit ID 240) over Modbus TCP (user guide M212287EN-AJ).
Also known as: Indigo510, Indigo520, Indigo500 series - Sensor (moisture in oil transmitter)
Vaisala MMT143 moisture in oil transmitter (Modbus RTU)
MMT143 moisture-in-oil transmitter ordered with the Modbus RTU option (user guide M213308EN-B).
Also known as: MMT143 - Sensor (HVAC humidity, temperature and CO2 transmitter)
Vaisala Origo10 transmitters for HVAC (Origo10A, Modbus RTU)
Origo10A duct and wall transmitters ordered with the Modbus RTU output (user guide M213293EN-B). Origo10L has no Modbus.
Also known as: Origo10, Origo10A, Origo 10, Vaisala Origo10 duct transmitter, Vaisala Origo10 wall transmitter - Sensor (precipitation)
Vaisala RM60 PRECICAP radar precipitation sensor (Modbus RTU)
RM60 sensors ordered with communication option 1 (RS-485 Modbus RTU) or switched to Modbus, per user guide M213218EN-B.
Also known as: RM60, PRECICAP RM60, Vaisala RM60 - Sensor (ultrasonic wind)
Vaisala WM80 ultrasonic wind sensor (Modbus RTU)
WM80 sensors with RS-485 in Modbus mode (e.g. ordering option C), per user guide M212995EN-F.
Also known as: WM80, Vaisala WM80, Ultrasonic Wind Sensor WM80 - Sensor (weather transmitter)
Vaisala WXT530 series weather transmitters (Modbus RTU)
WXT531-WXT536 weather transmitters with firmware 3.85 or later in Modbus RTU mode (user guide M211840EN-G).
Also known as: WXT531, WXT532, WXT533, WXT534, WXT535, WXT536 - Sensor (humidity and temperature probe)
Vaisala XMP10 humidity and temperature probe (Modbus RTU)
XMP10 probes ordered with (or switched to) Modbus RTU output, user guide M213279EN-A.
Also known as: XMP10, HUMICAP XMP10, Vaisala XMP10 - Sensor (CO2/humidity wall transmitter)
Vaisala XMW85 CO2, humidity and temperature wall transmitter (Modbus RTU)
XMW85 wall transmitter, Modbus RTU interface (user guide M213257EN-B).
Also known as: XMW85
Other valves, actuators & sensors register maps
- Sensor
VTS CO2-SENS-D-MODRTU
VTS CO2-SENS-D-MODRTU duct CO2 transducer (MH-Z19B sensing module), manual ver. 2.0 (11.2021).
Also known as: CO2 transducer CO2-SENS-D-MODRTU, VTS duct CO2 sensor - Sensor (limit controller)
Yokogawa UTAdvanced UT35A-L limit controller
Yokogawa UT35A-L limit controllers with RS-485 (Modbus RTU/ASCII); process monitoring D registers from IM 05P07A01-01EN chapter 12.
Also known as: UT35A-L - Actuator / valve (6-way pressure-independent change-over valve)
Belimo 6-way EPIV Modbus RTU (EP..R-R6+BAC)
Belimo 6-way EPIV EP..R-R6+BAC on Modbus RTU, per 6-way EPIV Modbus Register en-gb 2024-01 (general notes dated 16.12.2019).
Also known as: EP..R-R6+BAC, 6-way pressure-independent valve - Sensor
Fronius Fronius Sensor Card via Datamanager (SunSpec 302/303/307)
A Fronius Sensor Card connected to a Fronius Datamanager over Solar Net and republished by it as a SunSpec device; the same layout is used for the float and int+SF settings.
Also known as: Fronius Sensor Card, IG Sensor Card - Sensor (load-cell weight transmitter)
Laumas TLB4 four-channel weight transmitter (Modbus RTU / Modbus TCP)
Laumas TLB4 with the Modbus RTU port or the Modbus/TCP option; communication protocols manual version 1.12. Direct registers only.
Also known as: TLB4, TLB4 MODBUS, TLB4 Modbus/TCP - Actuator / valve
Rotork Modbus RTU Mk3 option card (IQ3, SI3/SI4, CK, CVA, CMA, K-range)
Rotork Modbus RTU Mk3 option module (MFU) in IQ3, SI3, SI4, CK, CVA (firmware CVA1.14 or later), CMA and K-range actuators, using the default Rotork database (register 80 = 0), per PUB091-004-00 issue 08/25.
Also known as: IQ3 Modbus, Rotork MFU Mk3, Modbus Mk3 module, SI3 Modbus, SI4 Modbus, CK Modbus, CVA Modbus, CMA Modbus, K-range Modbus
All valves, actuators & sensors Modbus register maps →
Source: MHT410 User Guide · M211737EN-J · rev. 2023-11. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.