- Home
- Modbus register maps
- Vaisala
- WM80 ultrasonic wind sensor (Modbus RTU)
Sensor (ultrasonic wind) · Modbus register map
Vaisala WM80 ultrasonic wind sensor (Modbus RTU) Modbus register map
Updated 19 November 2026
The Vaisala WM80 is a heated ultrasonic wind sensor aimed at uses that need continuous wind data, such as wind turbine control, ship navigation and dynamic positioning. On RS-485 it serves Modbus RTU or an ASCII/NMEA message. This map covers wind speed and direction (sample, instant, average, gust, lull, U/V components), sonic temperature, averaging and heating settings, serial settings, status words, monitoring values and test registers.
This page lists 47 Modbus registers for the Vaisala WM80 ultrasonic wind sensor (Modbus RTU) — 15 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Vaisala’s own free documentation (linked below) and checked against it.
- Manufacturer
- Vaisala
- Model
- WM80 ultrasonic wind sensor (Modbus RTU)
- Equipment type
- Sensor (ultrasonic wind)
- Registers
- 47 (15 writable)
- Transport
- Modbus RTU
- Default unit ID
- 240
- Default serial
- 19200 baud, 8N2
- Documented addressing
- hexadecimal, 0-based
- 32-bit word order
- CDAB low word first (word-swapped)
- Also known as
- WM80, Vaisala WM80, Ultrasonic Wind Sensor WM80
- Source document
- WM80 User Guide · M212995EN-F · rev. 2025-12
Integration notes: Vaisala WM80 ultrasonic wind sensor (Modbus RTU)
Read holding registers 0x0000-0x0015 in one request for speed, direction, gust, lull and sonic temperature as low-word-first floats, and check the status words at 0x0200-0x0209.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 4 | Wind speed, instant | FLOAT32 CDAB | Instant wind speed | Read |
| HR 6 | Wind direction, instant | FLOAT32 CDAB | Instant wind direction | Read |
| HR 8 | Wind speed, average | FLOAT32 CDAB | Average wind speed | Read |
| HR 14 | Wind speed, gust | FLOAT32 CDAB | Gust | Read |
| HR 512 | Device status | BITMAP16 | Device status | Read |
| HR 521 | Wind measurement status | BITMAP16 | Wind measurement status | Read |
Enable Modbus control & writes
Order the sensor with the Modbus RTU communication profile (option C), or in Vaisala Insight PC software select Communication, set Interface mode to Modbus RTU, save, then power-cycle the sensor. Interface mode is also register 0x0605.
Byte order & addressing
- Floats and int32 are low word first (CDAB).
- Default framing is 8 data bits, no parity, 2 stop bits.
Network setup
- Defaults: address 240, 19200 baud, N82.
- Serial defaults in the register table apply unless the ordered configuration specifies otherwise; check the configuration code with Insight if unsure.
- If the Modbus client runs on the same PC as Insight, close Insight first; restart the sensor after changing settings.
Watch out for
- Read the test registers 0x1F00-0x1F02 first to confirm addressing and word order.
Vaisala WM80 ultrasonic wind sensor (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 0x0000 (0) | Wind speed, sample | 10 Hz sample. | FLOAT32 | CDAB | m/s | Read | ||
| HR | 2doc 0x0002 (2) | Wind direction, sample | FLOAT32 | CDAB | deg | Read | |||
| HR | 4doc 0x0004 (4) | Wind speed, instant | Moving average over the instant averaging period. | FLOAT32 | CDAB | m/s | Read | ||
| HR | 6doc 0x0006 (6) | Wind direction, instant | FLOAT32 | CDAB | deg | Read | |||
| HR | 8doc 0x0008 (8) | Wind speed, average | Moving average over the statistics period. | FLOAT32 | CDAB | m/s | Read | ||
| HR | 10doc 0x000a (10) | Wind direction, average | FLOAT32 | CDAB | deg | Read | |||
| HR | 12doc 0x000c (12) | Wind speed, lull | Minimum instant speed over the statistics period. | FLOAT32 | CDAB | m/s | Read | ||
| HR | 14doc 0x000e (14) | Wind speed, gust | Maximum instant speed over the statistics period. | FLOAT32 | CDAB | m/s | Read | ||
| HR | 16doc 0x0010 (16) | Wind direction, lull | FLOAT32 | CDAB | deg | Read | |||
| HR | 18doc 0x0012 (18) | Wind direction, gust | FLOAT32 | CDAB | deg | Read | |||
| HR | 20doc 0x0014 (20) | Sonic temperature | FLOAT32 | CDAB | °C | Read | |||
| HR | 22doc 0x0016 (22) | Wind speed U, sample | FLOAT32 | CDAB | m/s | Read | |||
| HR | 24doc 0x0018 (24) | Wind speed V, sample | FLOAT32 | CDAB | m/s | Read | |||
| HR | 26doc 0x001a (26) | Wind speed U, instant | FLOAT32 | CDAB | m/s | Read | |||
| HR | 28doc 0x001c (28) | Wind speed V, instant | FLOAT32 | CDAB | m/s | Read | |||
| HR | 30doc 0x001e (30) | Wind speed U, average | FLOAT32 | CDAB | m/s | Read | |||
| HR | 32doc 0x0020 (32) | Wind speed V, average | FLOAT32 | CDAB | m/s | Read | |||
| HR | 512doc 0x0200 (512) | Device status | 0 = device OK. | BITMAP16 | Read | bit 2 = Warning (W) | |||
| HR | 515doc 0x0203 (515) | Operating voltage status | 0 = operating voltage OK. | BITMAP16 | Read | bit 2 = Operating voltage too low (U); bit 3 = Operating voltage too high (O) | |||
| HR | 518doc 0x0206 (518) | Heating status | 0 = heating OK. | BITMAP16 | Read | bit 0 = Failure (F); bit 2 = Warning (W); bit 3 = Information (I) | |||
| HR | 521doc 0x0209 (521) | Wind measurement status | 0 = wind measurement OK. | BITMAP16 | Read | bit 0 = Measurement volume blocked (S) | |||
| HR | 768doc 0x0300 (768) | Wind averaging method | INT16 | Read/write | 0 = Scalar averaging; 1 = Vector averaging | ||||
| HR | 771doc 0x0303 (771) | Wind instant averaging period | 0.1-10 s, default 3.0. | FLOAT32 | CDAB | s | Read/write | ||
| HR | 773doc 0x0305 (773) | Wind statistics period | 0.1-3600 s, default 600. | FLOAT32 | CDAB | s | Read/write | ||
| HR | 775doc 0x0307 (775) | Invalidation delay | 0-20 s, default 4.0. | FLOAT32 | CDAB | s | Read/write | ||
| HR | 777doc 0x0309 (777) | Wind direction offset | -180 to 180, default 0. | FLOAT32 | CDAB | deg | Read/write | ||
| HR | 779doc 0x030b (779) | Calm wind threshold | 0.2-100, default 0.2. | FLOAT32 | CDAB | m/s | Read/write | ||
| HR | 783doc 0x030f (783) | Heating maximum current | 0-10 A, default 10. | FLOAT32 | CDAB | A | Read/write | ||
| HR | 785doc 0x0311 (785) | Heating temperature setpoint | 0-55 °C, default 45. | FLOAT32 | CDAB | °C | Read/write | ||
| HR | 1280doc 0x0500 (1280) | Heating enabled | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 1536doc 0x0600 (1536) | Restart device | Write 1 to restart. | INT16 | Read/write | ||||
| HR | 1538doc 0x0602 (1538) | Bit rate | INT16 | Read/write | 0 = 1200; 1 = 2400; 2 = 4800; 3 = 9600; 4 = 19200; 5 = 38400; 6 = 57600; 7 = 115200 | ||||
| HR | 1539doc 0x0603 (1539) | Parity, data, stop bits | INT16 | Read/write | 0 = N81; 1 = N82; 2 = E81; 3 = E82; 4 = O81; 5 = O82; 6 = N71; 7 = N72; 8 = E71; 9 = E72; 10 = O71; 11 = O72 | ||||
| HR | 1541doc 0x0605 (1541) | Interface mode | INT16 | Read/write | 0 = Modbus; 1 = ASCII/NMEA | ||||
| HR | 1542doc 0x0606 (1542) | Modbus address | 1-247, default 240. | INT16 | Read/write | ||||
| HR | 7424doc 0x1d00 (7424) | Vendor name | STRING[16] | Read | |||||
| HR | 7432doc 0x1d08 (7432) | Product code | STRING[16] | Read | |||||
| HR | 7440doc 0x1d10 (7440) | Product serial number | STRING[16] | Read | |||||
| HR | 7680doc 0x1e00 (7680) | Restore factory default settings | Write 1 to restore. | INT16 | Read/write | ||||
| HR | 7936doc 0x1f00 (7936) | Signed integer test | Always reads -12345. | INT16 | Read | ||||
| HR | 7937doc 0x1f01 (7937) | Floating point test | Always reads -123.45. | FLOAT32 | CDAB | Read | |||
| HR | 32768doc 0x8000 (32768) | Uptime | INT32 | CDAB | s | Read | |||
| HR | 32770doc 0x8002 (32770) | Operating voltage | FLOAT32 | CDAB | V | Read | |||
| HR | 32778doc 0x800a (32778) | Heating current | FLOAT32 | CDAB | A | Read | |||
| HR | 32780doc 0x800c (32780) | Transducer 1 temperature | FLOAT32 | CDAB | °C | Read | |||
| HR | 32782doc 0x800e (32782) | Transducer 2 temperature | FLOAT32 | CDAB | °C | Read | |||
| HR | 32784doc 0x8010 (32784) | Transducer 3 temperature | FLOAT32 | CDAB | °C | Read |
Notes on this map
- All registers are holding registers: read with function 03, write with function 16; function 43 (0x2B) reads device ID.
- int32 and float values are two registers in little-endian word order (least significant word first, CDAB), as the guide's data-type table states. Bytes inside each register are big-endian.
- Ordering option C ships as Modbus RTU, 19200 bps, N, 8, 2, address 240; the register table also lists 19200 and N82 as defaults.
- Left out: the analog output 1/2 settings (Tables 57-58), the diagnostic code int32 registers (reserved for Vaisala diagnostics), product order code, manufacturing date and product name.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Vaisala WM80 ultrasonic wind sensor (Modbus RTU)
What Modbus registers does the Vaisala WM80 ultrasonic wind sensor (Modbus RTU) have?
This map lists 47 registers: 47 holding registers. 15 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Vaisala WM80 ultrasonic wind sensor (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The guide prints each register as a hex address with its decimal value (used on the wire) plus a 'register number' equal to the address + 1. Wind speed sample is at address 0x0000 (register number 1).
What byte order does the Vaisala WM80 ultrasonic wind sensor (Modbus RTU) use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Vaisala WM80 ultrasonic wind sensor (Modbus RTU)?
Start with HR 4 Wind speed, instant (Instant wind speed); HR 6 Wind direction, instant (Instant wind direction); HR 8 Wind speed, average (Average wind speed); HR 14 Wind speed, gust (Gust); HR 512 Device status (Device status); HR 521 Wind measurement status (Wind measurement status).
How do I enable Modbus control of the Vaisala WM80 ultrasonic wind sensor (Modbus RTU)?
Order the sensor with the Modbus RTU communication profile (option C), or in Vaisala Insight PC software select Communication, set Interface mode to Modbus RTU, save, then power-cycle the sensor. Interface mode is also register 0x0605.
Where is the official Vaisala WM80 ultrasonic wind sensor (Modbus RTU) Modbus documentation?
The source is WM80 User Guide (M212995EN-F), revision 2025-12, published free by Vaisala at https://docs.vaisala.com/r/M212995EN-F/en-US.
More Vaisala Modbus register maps
- Sensor (dew point probe)
Vaisala DMP Series dew point probes (DMP5, DMP6, DMP7, DMP8) (Modbus RTU)
Vaisala DMP5, DMP6, DMP7 and DMP8 dew point and temperature probes, Modbus RTU interface (user guide M212357EN-F).
Also known as: DMP5, DMP6, DMP7, DMP8, DRYCAP DMP series - Sensor (dew point transmitter)
Vaisala DMT143 miniature dew point transmitter (Modbus RTU)
DMT143 dew point transmitters ordered with the Modbus RTU option (user guide M211435EN-L).
Also known as: DMT143, DRYCAP DMT143 - Sensor (dew point transmitter)
Vaisala DMT153 dew point transmitter (Modbus RTU)
DMT153 trace-moisture dew point transmitter, Modbus RTU interface (user guide M213149EN-B).
Also known as: DMT153, DRYCAP DMT153 - Sensor (CO2 duct transmitter)
Vaisala GMD110 duct CO2 transmitter (Modbus RTU)
GMD110 duct-mount CO2 transmitter, Modbus RTU interface (user guide M212885EN-B).
Also known as: GMD110, CARBOCAP GMD110 - Sensor (CO2 probe)
Vaisala GMP251 CARBOCAP carbon dioxide probe (Modbus RTU)
GMP251 probe in Modbus RTU mode, user guide M211799EN-N.
Also known as: GMP251, CARBOCAP GMP251, Vaisala GMP251 - Sensor (CO2 probe)
Vaisala GMP252 CARBOCAP carbon dioxide probe (Modbus RTU)
GMP252 probe in Modbus RTU mode, user guide M211897EN-G.
Also known as: GMP252, CARBOCAP GMP252, Vaisala GMP252 - Sensor (CO2 wall transmitter)
Vaisala GMW87 CO2 and temperature wall transmitter (Modbus RTU)
GMW87, the RS-485 Modbus RTU model of the GMW80 series (user guide M211748EN-H).
Also known as: GMW87, GMW80 series Modbus - Sensor (humidity and temperature transmitter)
Vaisala HMDW110 series humidity and temperature transmitters with TMI110 (Modbus RTU)
HMDW110-series duct, wall and outdoor transmitters and TMI110 ordered with the Modbus RTU option (user guide M211726EN-L).
Also known as: HMD110, HMD112, HMW110, HMW112, HMW112D, HMS110, HMS112, TMW110, TMW112, TMW112D, TMI110 - Sensor (humidity and temperature module)
Vaisala HMM170 humidity module (Modbus RTU)
HMM170 OEM humidity and temperature module with the Modbus RTU interface (user guide M212259EN-D).
Also known as: HMM170, HUMICAP HMM170 - Sensor (humidity and temperature probe)
Vaisala HMP Series (HMP1-HMP9) with MMP8 and TMP1 probes (Modbus RTU)
Vaisala HMP1/3/4/5/7/8/9, TMP1 and MMP8 probes with the Modbus RTU interface (user guide M212022EN-M).
Also known as: HMP1, HMP3, HMP4, HMP5, HMP7, HMP8, HMP9, TMP1, MMP8 - Sensor (humidity and temperature probe)
Vaisala HMP60 / HMP110 series humidity and temperature probes (Modbus RTU)
HMP60/HMP110-series probes ordered with the Modbus RTU option (user guide M211060EN-N).
Also known as: HMP110, HMP113, HMP115, TMP115, HMP60, HMP63, HUMICAP HMP110, HMP110T, HMP63T, HMP115T - Sensor (humidity and temperature transmitter)
Vaisala HMW87 / HMW87D wall humidity and temperature transmitters (Modbus RTU)
HMW87 and HMW87D wall transmitters of the HMDW80 series (the Modbus models in user guide M211510EN-J).
Also known as: HMW87, HMW87D, HMDW80 Modbus - Sensor (H2O2 probe)
Vaisala HPP271 hydrogen peroxide probe (Modbus RTU)
HPP271 vaporized hydrogen peroxide probe, Modbus RTU interface (user guide M211888EN-E).
Also known as: HPP271, PEROXCAP HPP271 - Sensor (H2O2 / humidity probe)
Vaisala HPP272 hydrogen peroxide, humidity and temperature probe (Modbus RTU)
HPP272 vaporized hydrogen peroxide probe, Modbus RTU interface (user guide M211972EN-G).
Also known as: HPP272, PEROXCAP HPP272 - Sensor transmitter (host for Vaisala probes)
Vaisala Indigo510 / Indigo520 transmitters (Modbus TCP)
Indigo510 and Indigo520 transmitter registers (unit ID 240) over Modbus TCP (user guide M212287EN-AJ).
Also known as: Indigo510, Indigo520, Indigo500 series - Sensor (transformer oil monitor)
Vaisala MHT410 moisture, hydrogen and temperature transmitter for transformer oil (Modbus RTU)
MHT410 transformer oil monitor, Modbus RTU on the RS-485 screw terminals (user guide M211737EN-J).
Also known as: MHT410 - Sensor (moisture in oil transmitter)
Vaisala MMT143 moisture in oil transmitter (Modbus RTU)
MMT143 moisture-in-oil transmitter ordered with the Modbus RTU option (user guide M213308EN-B).
Also known as: MMT143 - Sensor (HVAC humidity, temperature and CO2 transmitter)
Vaisala Origo10 transmitters for HVAC (Origo10A, Modbus RTU)
Origo10A duct and wall transmitters ordered with the Modbus RTU output (user guide M213293EN-B). Origo10L has no Modbus.
Also known as: Origo10, Origo10A, Origo 10, Vaisala Origo10 duct transmitter, Vaisala Origo10 wall transmitter - Sensor (precipitation)
Vaisala RM60 PRECICAP radar precipitation sensor (Modbus RTU)
RM60 sensors ordered with communication option 1 (RS-485 Modbus RTU) or switched to Modbus, per user guide M213218EN-B.
Also known as: RM60, PRECICAP RM60, Vaisala RM60 - Sensor (weather transmitter)
Vaisala WXT530 series weather transmitters (Modbus RTU)
WXT531-WXT536 weather transmitters with firmware 3.85 or later in Modbus RTU mode (user guide M211840EN-G).
Also known as: WXT531, WXT532, WXT533, WXT534, WXT535, WXT536 - Sensor (humidity and temperature probe)
Vaisala XMP10 humidity and temperature probe (Modbus RTU)
XMP10 probes ordered with (or switched to) Modbus RTU output, user guide M213279EN-A.
Also known as: XMP10, HUMICAP XMP10, Vaisala XMP10 - Sensor (CO2/humidity wall transmitter)
Vaisala XMW85 CO2, humidity and temperature wall transmitter (Modbus RTU)
XMW85 wall transmitter, Modbus RTU interface (user guide M213257EN-B).
Also known as: XMW85
Other valves, actuators & sensors register maps
- Water treatment controller (Sensor / controller)
Walchem W900 water treatment controller (Modbus/TCP)
Walchem W900 controllers (software 3.01 and up) with the Modbus/TCP feature, per Modbus manual 180676.K. W600, Intuition-6 and Intuition-9 use the same type maps but different block start addresses.
Also known as: W900 series - Sensor (Ethernet analog output module)
Acromag BusWorks XT1531-000 4-channel current output + 4 digital I/O (Modbus TCP)
BusWorks XT1531-000 per its user's manual (file revision H, 18 Nov 2022).
Also known as: XT1531-000, XT1531, BusWorks XT1531 - Sensor (humidity / temperature transmitter)
Dwyer Series RHPX communicating humidity/temperature transmitter
Dwyer Series RHPX humidity and temperature transmitters with the BACnet MS/TP / Modbus RTU communication board, set to Modbus with DIP switch 9 (bulletin AQ-RHPX-C).
Also known as: RHPX, Dwyer RHPX BACnet/Modbus, 607xxx - Sensor (turbidity)
JUMO ecoLine NTU digital turbidity sensor (Modbus RTU)
JUMO ecoLine NTU type 202670 with RS-485 Modbus RTU (interface description V1.01).
Also known as: 202670, JUMO ecoLine NTU, ecoLine NTU type 202670 - Sensor (vibration / temperature)
Machine Saver TriVibe vibration and temperature sensor (Modbus RTU)
Machine Saver TriVibe triaxial vibration sensors on RS-485 Modbus RTU, per the 'Modbus Registers Map' page of the Machine Saver online library (revision #12).
Also known as: TriVibe, Machine Saver TriVibe - Sensor (conductivity controller)
Shinko Technos AER-102-ECH conductivity indicating controller (C5 option)
Shinko AER-102-ECH electrical conductivity controller with the C5 RS-485 option; manual No. AER11CECE5.
Also known as: AER-102-ECH
All valves, actuators & sensors Modbus register maps →
Source: WM80 User Guide · M212995EN-F · rev. 2025-12. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.