- Home
- Modbus register maps
- Carlo Gavazzi
- DCT1 DC energy meter (Modbus RTU)
Energy meter (DC) · Modbus register map
Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) Modbus register map
Updated 17 November 2026
The DCT1 is a DC energy meter with an internal shunt, built for EV charging and DC distribution, with an RS485 Modbus RTU port. Readings are 32-bit integers sent low word first with fixed weights. This map covers voltage, current, power, imported and exported energy and Ah, run-hour counters, shunt temperatures, cable-loss value, serial settings, resets and the device state word.
This page lists 37 Modbus registers for the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) — 10 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Carlo Gavazzi’s own free documentation (linked below) and checked against it.
- Manufacturer
- Carlo Gavazzi
- Model
- DCT1 DC energy meter (Modbus RTU)
- Equipment type
- Energy meter (DC)
- Registers
- 37 (10 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- CDAB low word first (word-swapped)
- Also known as
- DCT1A60V10LS1X, DCT1A60V10LS2EC, DCT1A60V10LS3EC, DCT1A30V10LS1X, DCT1A30V10LS2EC, DCT1A30V10LS3EC
Integration notes: Carlo Gavazzi DCT1 DC energy meter (Modbus RTU)
Read input registers 0000h-0005h (function 04 or 03) for volts, amps and watts, and 0010h-0027h for energy and Ah; decode INT32 low word first and apply the fixed weights (V and W x10, A x1000, kWh and Ah x10).
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | Voltage | INT32 CDAB | DC voltage | Read |
| IR 2 | Current | INT32 CDAB | DC current | Read |
| IR 4 | Power | INT32 CDAB | DC power | Read |
| IR 16 | kWh (+) TOT | INT32 CDAB | Imported energy total | Read |
| IR 32 | kWh (-) TOT | INT32 CDAB | Exported energy total | Read |
| HR 20498 | Device state | BITMAP16 | Device state / over-range flags | Read |
Enable Modbus control & writes
Modbus RTU is always on. Set address, baud, parity and stop bits at 2000h-2003h, then write 1 to 2010h to apply them.
Byte order & addressing
- 32-bit values are low word first (CDAB).
- Energy totals carry 0.1 kWh resolution; run hours are in 1/100 h.
- On certified (signed) versions the total-energy reset is blocked.
Network setup
- Defaults: address 1, 9600 baud, no parity, 1 stop bit, 20 ms reply delay.
- Terminate both bus ends with 120 ohm; above 1000 m or 160 devices add a repeater.
Watch out for
- New serial settings only take effect after writing 1 to 2010h.
- Max answer time is about 160 ms; retry 2-3 times before declaring the meter offline.
Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 300001 / 0000h | Voltage | INT32 | CDAB | × 0.1 | V | Read | ||
| IR | 2doc 300003 / 0002h | Current | INT32 | CDAB | × 0.001 | A | Read | ||
| IR | 4doc 300005 / 0004h | Power | Signed DC power. | INT32 | CDAB | × 0.1 | W | Read | |
| IR | 11doc 300012 / 000Bh | Carlo Gavazzi identification code | Read one word at a time. | UINT16 | Read | 1808 = DCT1A60V10LS1X; 1809 = DCT1A60V10LS2EC; 1810 = DCT1A60V10LS3EC; 1812 = DCT1A30V10LS1X; 1813 = DCT1A30V10LS2EC; 1814 = DCT1A30V10LS3EC | |||
| IR | 16doc 300017 / 0010h | kWh (+) TOT | INT32 | CDAB | × 0.1 | kWh | Read | ||
| IR | 18doc 300019 / 0012h | Ah (+) TOT | INT32 | CDAB | × 0.1 | Ah | Read | ||
| IR | 20doc 300021 / 0014h | kWh (+) PAR | INT32 | CDAB | × 0.1 | kWh | Read | ||
| IR | 22doc 300023 / 0016h | Ah (+) PAR | INT32 | CDAB | × 0.1 | Ah | Read | ||
| IR | 32doc 300033 / 0020h | kWh (-) TOT | INT32 | CDAB | × 0.1 | kWh | Read | ||
| IR | 34doc 300035 / 0022h | Ah (-) TOT | INT32 | CDAB | × 0.1 | Ah | Read | ||
| IR | 36doc 300037 / 0024h | kWh (-) PAR | INT32 | CDAB | × 0.1 | kWh | Read | ||
| IR | 38doc 300039 / 0026h | Ah (-) PAR | INT32 | CDAB | × 0.1 | Ah | Read | ||
| IR | 44doc 300045 / 002Ch | Run hour meter | INT32 | CDAB | × 0.01 | h | Read | ||
| IR | 46doc 300047 / 002Eh | Run hour meter kWh- | Hours counted while energy flows in the negative direction. | INT32 | CDAB | × 0.01 | h | Read | |
| IR | 48doc 300049 / 0030h | Run hour meter ON time | Hours the meter has been powered. | INT32 | CDAB | × 0.01 | h | Read | |
| IR | 50doc 300051 / 0032h | Run hour meter PAR | INT32 | CDAB | × 0.01 | h | Read | ||
| IR | 52doc 300053 / 0034h | Run hour meter kWh- PAR | INT32 | CDAB | × 0.01 | h | Read | ||
| IR | 54doc 300055 / 0036h | Run hour meter ON time PAR | INT32 | CDAB | × 0.01 | h | Read | ||
| IR | 80doc 300081 / 0050h | T1 (shunt terminal 1 temperature) | INT32 | CDAB | × 0.1 | °C | Read | ||
| IR | 82doc 300083 / 0052h | T2 (shunt terminal 2 temperature) | INT32 | CDAB | × 0.1 | °C | Read | ||
| IR | 770doc 300771 / 0302h | Firmware version and revision | High byte: bits 0-3 minor, bits 4-7 major; low byte: revision. | UINT16 | Read | ||||
| HR | 4355doc 304356 / 1103h | Easy connection | UINT16 | Read/write | 0 = Disabled (default); 1 = Enabled | ||||
| HR | 4363doc 304360 / 110Bh | Startup current of run hour counter | Range 480-600000 (0.48-600 A), default 480. Write with function 10h only. | UINT32 | CDAB | × 0.001 | A | Read/write | |
| HR | 8192doc 308193 / 2000h | RS485 instrument address | 1-247, default 1. | UINT16 | Read/write | ||||
| HR | 8193doc 308194 / 2001h | RS485 baud rate | UINT16 | Read/write | 1 = 9.6 kbps (default); 2 = 19.2 kbps; 3 = 38.4 kbps; 4 = 57.6 kbps; 5 = 115.2 kbps | ||||
| HR | 8194doc 308195 / 2002h | RS485 parity | UINT16 | Read/write | 1 = No parity (default); 2 = Even parity | ||||
| HR | 8195doc 308196 / 2003h | Stop bit | UINT16 | Read/write | 1 = 1 (default); 2 = 2 | ||||
| HR | 8196doc 308197 / 2004h | RS485 delay on reply | 0-1000, default 20. | UINT16 | ms | Read/write | |||
| HR | 8208doc 308209 / 2010h | Update serial communication settings | Write 1 to apply new serial settings; other values do nothing. | UINT16 | Read/write | ||||
| HR | 9471doc 309472 / 24FFh | Signature type | UINT16 | Read | 0 = 256-bit signature; 1 = 384-bit signature; 2 = No signature | ||||
| HR | 16387doc 316388 / 4003h | Reset total counters | Write 1. Non-certified: totals, Ah, run hours. Certified: Ah and run hours only. | UINT16 | Read/write | ||||
| HR | 16388doc 316389 / 4004h | Reset partial counters | Write 1 to clear partial energy, Ah and run-hour counters. | UINT16 | Read/write | ||||
| HR | 20487doc 320488 / 5007h | Production year | Four digits. | UINT16 | Read | ||||
| HR | 20498doc 320499 / 5012h | Device state | BITMAP16 | Read | bit 0 = Voltage over range (beyond ±1150.1 V); bit 1 = Current over range (±600.1 A on A60 models, ±300.1 A on A30 models); bit 2 = Terminal 1 temperature below -25.1 °C; bit 3 = Terminal 1 temperature above 120.1 °C; bit 4 = Terminal 2 temperature below -25.1 °C; bit 5 = Terminal 2 temperature above 120.1 °C; bit 15 = Internal device fault | ||||
| HR | 20499doc 320500 / 5013h | Shunt temperature position 1 | UINT16 | × 0.1 | °C | Read | |||
| HR | 20500doc 320501 / 5014h | Shunt temperature position 2 | UINT16 | × 0.1 | °C | Read | |||
| HR | 20736doc 320737 / 5100h | Cable loss value | Cable resistance used to correct energy. | INT32 | CDAB | mOhm | Read |
Notes on this map
- Word order: the protocol says INT32, UINT32 and UINT64 are sent least significant word first, bytes MSB first, so 32-bit values here are CDAB.
- Left out: the FLOAT block at 0200h (word order for IEEE 754 values is not stated), the INT64 high-resolution energy blocks at 0500h and 0600h (word order is stated only for UINT64, not INT64), the mirror INT32 block at 0100h-0124h, the signed OBIS data maps at 0700h and 0800h, public key, signatures, device tag and serial-number ASCII words, maintenance mode and the cable-loss datalogger.
- The ID code (000Bh) and firmware word (0302h) may only be read one word at a time.
- Reading an address not in the tables returns an illegal data address exception.
- The factory-reset sequence at 4020h (write 0x0A0A then 0xC1A0 within 5 s) is not listed as a register.
- Start-up current of run hour counter is printed as Modicon 304360 next to hex 110Bh; the hex address (wire 4363) is used.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU)
What Modbus registers does the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) have?
This map lists 37 registers: 21 input registers, 16 holding registers. 10 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Each row gives a 6-digit Modicon number (3xxxxx) and the hex physical address; the hex value goes in the frame. 300001 / 0000h is read at wire address 0. Functions 03 and 04 both read the measurement tables.
What byte order does the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU)?
Start with IR 0 Voltage (DC voltage); IR 2 Current (DC current); IR 4 Power (DC power); IR 16 kWh (+) TOT (Imported energy total); IR 32 kWh (-) TOT (Exported energy total); HR 20498 Device state (Device state / over-range flags).
How do I enable Modbus control of the Carlo Gavazzi DCT1 DC energy meter (Modbus RTU)?
Modbus RTU is always on. Set address, baud, parity and stop bits at 2000h-2003h, then write 1 to 2010h to apply them.
Where is the official Carlo Gavazzi DCT1 DC energy meter (Modbus RTU) Modbus documentation?
The source is DCT1 Modbus Communication Protocol - Public version (Version 1.1), revision 2024-02-13, published free by Carlo Gavazzi at https://www.gavazziautomation.com/fileadmin/images/PIM/OTHERSTUFF/COMPRO/DCT1_CPP_%20V1.1_05042024.pdf.
More Carlo Gavazzi Modbus register maps
- Energy meter (DC)
Carlo Gavazzi DCM1 DC energy meter for EV chargers (Modbus RTU / TCP)
DCM1 300 A / 600 A, 1000 V DC meters (MID, Eichrecht and LNE variants) with RS485 and Ethernet, protocol version 1.11.
Also known as: DCM1A60V10L20S1PFA, DCM1A60V10L20S1PFB, DCM1A60V10L20S2DEB, DCM1A60V10L20S3DEB, DCM1A60V10L20S2DEBF, DCM1A60V10L20S3DEBF, DCM1A30V10L20S1PFA, DCM1A30V10L20S1PFB, DCM1A30V10L20S2DEB, DCM1A30V10L20S3DEB, DCM1A30V10L20S2DEBF, DCM1A30V10L20S3DEBF, DCM1A60V10L20S1ULB, DCM1A30V10L20S1ULB - Energy meter
Carlo Gavazzi EM100 / ET100 series (EM111, EM112, ET112)
Single-phase EM111, EM112 energy meters and ET112 bidirectional meter with the S1 (RS485 Modbus RTU) port, protocol version 2 revision 14.
Also known as: EM111, EM112, ET112, EM110, EM111-DIN, EM112-DIN, ET112-DIN, EM111DINAV81XS1X, EM112DINAV01XS1X, ET112DINAV01XS1X - Energy meter (energy analyzer)
Carlo Gavazzi EM210 (AV versions)
EM210 three-phase energy analyzers, AV input versions with the RS485 Modbus RTU option, protocol version 4 revision 3 (newest variables need firmware A.5/A.6).
Also known as: EM210, EM210-72D, EM210 AV - Energy meter (energy analyzer)
Carlo Gavazzi EM24-DIN (PFA, PFB and X models)
EM24-DIN three-phase energy analyzers, PFA/PFB (MID) and X models with the RS485 Modbus RTU port (IS option), protocol version 4 revision 0.
Also known as: EM24, EM24DIN, EM24DINAV93XISPFA, EM24DINAV93XISPFB, EM24DINAV93XISX, EM24DINAV53XISX, EM24DINAV23XISX, EM24 DIN AV9, EM24 DIN AV5 - Energy meter (energy analyzer)
Carlo Gavazzi EM24-DIN Ethernet (E1)
EM24-DIN energy analyzers with the E1 Ethernet (RJ45) Modbus TCP port, AV2 and AV5 inputs, X/PFA/PFB, protocol version 0 revision 1.3 (FW 1.0).
Also known as: EM24 E1, EM24_E1, EM24DINAV23XE1X, EM24DINAV23XE1PFA, EM24DINAV23XE1PFB, EM24DINAV53XE1X, EM24DINAV53XE1PFA, EM24DINAV53XE1PFB - Energy meter
Carlo Gavazzi EM24-IS (SFA and SFB models)
EM24-DIN AV2/AV5 IS SFA and SFB versions (identification codes 1696-1699), protocol revision 2.0.
Also known as: EM24DINAV23XISSFA, EM24DINAV53XISSFA, EM24DINAV23XISSFB, EM24DINAV53XISSFB, EM24 SFA, EM24 SFB - Energy meter
Carlo Gavazzi EM270 / EM280 dual three-phase energy meters with TCD current sensors
EM270 X (firmware r.b0+), EM270 W (r.C0+) and EM280 (r.E0+) on RS485 Modbus RTU, per communication protocol version 5 revision 1 (2018-01-29).
Also known as: EM270, EM280, EM270 X, EM270 W, EM27072DMV53X2SX, EM28072DMV53X2SX - Energy meter
Carlo Gavazzi EM271 dual three-phase energy meter with TCD current sensors
EM271 (firmware r.d0+, PF values from r.d2) on RS485 Modbus RTU, per communication protocol version 1 revision 2 (2018-01-29).
Also known as: EM271, EM27172DMV53X2SX, EM27172DMV63X2SX - Energy meter
Carlo Gavazzi EM300 / ET300 series (EM330, EM340, ET330, ET340)
EM330, EM331, EM340, EM341 energy meters and ET330/ET340 bidirectional meters with the S1 (RS485 Modbus RTU) port, protocol version 2 revision 17.
Also known as: EM330, EM340, ET330, ET340, EM331, EM341, EM330-DIN, EM340-DIN, ET340-DIN, EM340DINAV23XS1X, EM340DINAV23XS1PFA, EM340DINAV23XS1PFB - Energy meter
Carlo Gavazzi EM511 single-phase energy meter (Modbus RTU)
EM511 direct-connected single-phase DIN meters with RS485 and digital input (X, PFA, PFB, SFA versions), protocol rev. 1.8.
Also known as: EM511-IS, EM511DINAV81XS1X, EM511DINAV81XS1PFA, EM511DINAV81XS1PFB, EM511DINAV81XS1SFA - Energy meter
Carlo Gavazzi EM530 / EM540 three-phase energy meters (RS485 Modbus)
EM530 (CT-connected) and EM540 (direct-connected) with the S1 RS485 port, X and MID (PFA/PFB/PFC) versions, protocol document version 1.3.
Also known as: EM530, EM540, EM530DINAV53XS1X, EM530DINAV53XS1PFA, EM530DINAV53XS1PFB, EM530DINAV53XS1PFC, EM540DINAV23XS1X, EM540DINAV23XS1PFA, EM540DINAV23XS1PFB, EM540DINAV23XS1PFC, EM500 series - Energy meter
Carlo Gavazzi EM580 three-phase AC energy meter for EV chargers (Modbus RTU)
EM580-IS MID/Eichrecht AC meters (DEB, DET, DEA variants, 256/384-bit signatures), protocol version 1.11.
Also known as: EM580-IS, EM580DINAV23XS2DEB, EM580DINAV23XS3DEB, EM580DINAV23XS2DET, EM580DINAV23XS3DET, EM580DINAV23XS2DEA, EM580DINAV23XS3DEA - Power meter (power analyzer)
Carlo Gavazzi WM14 Advanced / CPT-DIN Advanced power analyzer (legacy)
WM14 Advanced (revision 5 onward) and CPT-DIN Advanced (revision 6 onward) with RS485 (or RS232 on CPT-DIN), protocol version 2 revision 2 (2008-01-09).
Also known as: WM14-96 Advanced, WM14 A, CPT-DIN Advanced, CPT A, CPT-DIN A - Power meter (power analyzer)
Carlo Gavazzi WM15 power analyzer
WM15-96 three-phase panel power analyzers with RS485 Modbus RTU (OS / OSPF / HOS versions), protocol version 1.2.
Also known as: WM15, WM15-96, WM1596AV53XOSX, WM1596AV53XOSPFB, WM1596AV53HOSX - Power meter (power analyzer)
Carlo Gavazzi WM20 / WM30 / WM40 power analyzers
WM20, WM30 and WM40 modular power analyzers with an RS485 (or Ethernet) Modbus module, protocol internal version rev. 4.0 (2018-03-28); WM30 = firmware letter X, WM40 = Y, WM20 = Z.
Also known as: WM20, WM30, WM40, WM20-96, WM30-96, WM40-96 - Power meter (power analyzer)
Carlo Gavazzi WM50 power analyzer with TCD branch channels
WM50 base unit (firmware X0, i.e. all A and B versions) with an MC485232 or MCETH communication module, plus TCD branch channels, per communication protocol user version rev. 1.0.0 (2017-09-27).
Also known as: WM50, WM50AV5, WM50-96, WM50 AV5
Other power & energy meters register maps
- Power meter (earth leakage breaker with reclosing and metering)
Circutor RECmax-CVM
Circutor RECmax-CVM earth-leakage circuit breaker with automatic reclosing and built-in analyzer, manual M175B01-03-22A.
- Energy meter
Eastron SDM120CT-40mA
Eastron SDM120CT-40mA single-phase CT-connected DIN-rail meter with RS485 Modbus RTU, user manual V1.0 (2026-07-16).
Also known as: SDM120CT-M-40mA, SDM120CT-M 40mA - Power meter
Eaton IQ 250 / IQ 260 Electronic Power Meter
Eaton IQ 250 and IQ 260 meters (including the L logging versions), Modbus map Appendix B of IB02601006E.
Also known as: IQ 250, IQ 260, IQ 250L, IQ 260L, IQ250, IQ260 - Sensor (clamp-on ultrasonic flowmeter)
Endress+Hauser Proline Prosonic Flow W 400 ultrasonic flowmeter (Modbus RS485)
Proline Prosonic Flow W 400 clamp-on flowmeter with the Modbus RS485 output, as described in GP01207D/06/EN/01.24.
Also known as: Prosonic Flow W 400 - Power meter
IME Nemo 72Le multifunction meter (MF724)
IME Nemo 72Le 72x72 panel meter MF724 with RS-485, per protocol PR141 (software 1.04).
Also known as: MF724, Nemo 72Le - Energy meter
inepro Metering 4PU / 4PS three-phase energy meter
4PU (meter code 1111) and 4PS (1112) MID three-phase DIN-rail meters with Modbus, user manual version 1.03 (2025).
Also known as: 4PU, 4PS, inepro 4PU, inepro 4PS
All power & energy meters Modbus register maps →
Source: DCT1 Modbus Communication Protocol - Public version · Version 1.1 · rev. 2024-02-13. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.