- Home
- Modbus register maps
- New Cosmos Electric
- PS-8 series extractive gas detector (Modbus TCP)
Sensor (extractive gas detector) · Modbus register map
New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) Modbus register map
Updated 17 November 2026
The PS-8 is a New Cosmos pump-sampling gas detector for semiconductor process and flammable gases, holding up to 16 sensor units. Its Ethernet port is a Modbus TCP server with all data in holding registers. This map covers the integer gas readings, decimal points and flow for all 16 channels, relay states, heartbeat, alarm reset, clock, and the channel 1 settings block (other channels repeat every 101 registers).
This page lists 117 Modbus registers for the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) — 34 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from New Cosmos Electric’s own free documentation (linked below) and checked against it.
- Manufacturer
- New Cosmos Electric
- Model
- PS-8 series extractive gas detector (Modbus TCP)
- Equipment type
- Sensor (extractive gas detector)
- Registers
- 117 (34 writable)
- Transport
- Modbus TCP
- Default unit ID
- Not stated
- TCP port
- 502
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- Also known as
- PS-8, PS-8 series, New Cosmos PS-8
Integration notes: New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP)
Connect over Ethernet to 192.168.0.101 port 502 and read holding registers 0-111 (seven words per sensor) with function 03; use the integer concentration and decimal registers for each channel.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 4 | Sensor 1 concentration (integer) | UINT16 | Sensor 1 concentration | Read |
| HR 5 | Sensor 1 decimal point | UINT16 | Sensor 1 decimal point | Read |
| HR 6 | Sensor 1 flow rate | UINT16 | Sensor 1 flow | Read |
| HR 112 | Heartbeat | UINT16 | Heartbeat | Read |
| HR 113 | Relay output monitor sensors 1/2 | UINT16 | Relay states sensors 1/2 | Read |
| HR 318 | Sensor 1 unit | UINT16 | Sensor 1 unit | Read/write |
Enable Modbus control & writes
Menu > Device Information > Modbus: select TCP/IP. Set IP and subnet (or DHCP) under Device Information.
Byte order & addressing
- Register 400xx minus 40001 = wire address.
- Reading starting at a reserved register gives an illegal-address error; reserved registers inside a longer read return 0.
- Date/time must be read or written as all three words together.
Network setup
- Factory IP 192.168.0.101, port 502 fixed.
- No proxy; the built-in web page at the IP shows live channel data for a quick check.
Watch out for
- Maintenance mode masks the alarm and fault bits of the status words.
- Settings marked change notification set a bit in 40124; clear it by writing 0.
New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 4doc 40005 | Sensor 1 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 5doc 40006 | Sensor 1 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 6doc 40007 | Sensor 1 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 11doc 40012 | Sensor 2 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 12doc 40013 | Sensor 2 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 13doc 40014 | Sensor 2 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 18doc 40019 | Sensor 3 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 19doc 40020 | Sensor 3 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 20doc 40021 | Sensor 3 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 25doc 40026 | Sensor 4 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 26doc 40027 | Sensor 4 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 27doc 40028 | Sensor 4 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 32doc 40033 | Sensor 5 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 33doc 40034 | Sensor 5 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 34doc 40035 | Sensor 5 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 39doc 40040 | Sensor 6 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 40doc 40041 | Sensor 6 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 41doc 40042 | Sensor 6 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 46doc 40047 | Sensor 7 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 47doc 40048 | Sensor 7 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 48doc 40049 | Sensor 7 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 53doc 40054 | Sensor 8 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 54doc 40055 | Sensor 8 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 55doc 40056 | Sensor 8 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 60doc 40061 | Sensor 9 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 61doc 40062 | Sensor 9 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 62doc 40063 | Sensor 9 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 67doc 40068 | Sensor 10 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 68doc 40069 | Sensor 10 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 69doc 40070 | Sensor 10 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 74doc 40075 | Sensor 11 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 75doc 40076 | Sensor 11 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 76doc 40077 | Sensor 11 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 81doc 40082 | Sensor 12 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 82doc 40083 | Sensor 12 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 83doc 40084 | Sensor 12 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 88doc 40089 | Sensor 13 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 89doc 40090 | Sensor 13 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 90doc 40091 | Sensor 13 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 95doc 40096 | Sensor 14 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 96doc 40097 | Sensor 14 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 97doc 40098 | Sensor 14 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 102doc 40103 | Sensor 15 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 103doc 40104 | Sensor 15 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 104doc 40105 | Sensor 15 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 109doc 40110 | Sensor 16 concentration (integer) | Gas reading x 10^decimal (next register). | UINT16 | Read | ||||
| HR | 110doc 40111 | Sensor 16 decimal point | UINT16 | Read | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | ||||
| HR | 111doc 40112 | Sensor 16 flow rate | Sample flow as an FL value (0x1F4 = FL500). | UINT16 | Read | ||||
| HR | 112doc 40113 | Heartbeat | Counts up once a second, 0-255 then wraps. | UINT16 | Read | ||||
| HR | 113doc 40114 | Relay output monitor sensors 1/2 | High byte sensor 1, low byte sensor 2; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 114doc 40115 | Relay output monitor sensors 3/4 | High byte sensor 3, low byte sensor 4; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 115doc 40116 | Relay output monitor sensors 5/6 | High byte sensor 5, low byte sensor 6; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 116doc 40117 | Relay output monitor sensors 7/8 | High byte sensor 7, low byte sensor 8; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 117doc 40118 | Relay output monitor sensors 9/10 | High byte sensor 9, low byte sensor 10; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 118doc 40119 | Relay output monitor sensors 11/12 | High byte sensor 11, low byte sensor 12; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 119doc 40120 | Relay output monitor sensors 13/14 | High byte sensor 13, low byte sensor 14; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 120doc 40121 | Relay output monitor sensors 15/16 | High byte sensor 15, low byte sensor 16; bits 0/1/2 = AL1/AL2/fault relay. | UINT16 | Read | ||||
| HR | 123doc 40124 | Setting change channel flags | Bit n set when channel n+1 settings changed; write 0 after reading. | BITMAP16 | Read/write | bit 0 = Channel 1 changed; bit 1 = Channel 2 changed; bit 2 = Channel 3 changed; bit 3 = Channel 4 changed; bit 4 = Channel 5 changed; bit 5 = Channel 6 changed; bit 6 = Channel 7 changed; bit 7 = Channel 8 changed; bit 8 = Channel 9 changed; bit 9 = Channel 10 changed; bit 10 = Channel 11 changed; bit 11 = Channel 12 changed; bit 12 = Channel 13 changed; bit 13 = Channel 14 changed; bit 14 = Channel 15 changed; bit 15 = Channel 16 changed | |||
| HR | 250doc 40251 | Alarm cancellation | Write 1 to cancel a latched alarm (manual-reset mode only). | UINT16 | Write | ||||
| HR | 253doc 40254 | Alarm cancellation mode | UINT16 | Read | 0 = Auto-resetting; 1 = Manual-resetting | ||||
| HR | 254doc 40255 | Collective contact AL1 setting | UINT16 | Read | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 255doc 40256 | Collective contact AL2 setting | UINT16 | Read | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 256doc 40257 | Collective fault contact setting | UINT16 | Read | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 258doc 40259 | Date/time: month and year | High byte month, low byte year 0-99; access the 3 date words together. | UINT16 | Read/write | ||||
| HR | 259doc 40260 | Date/time: hour and day | High byte hour (24 h), low byte day. | UINT16 | Read/write | ||||
| HR | 260doc 40261 | Date/time: seconds and minutes | High byte seconds, low byte minutes. | UINT16 | Read/write | ||||
| HR | 308doc 40309 | Sensor 1 alarm AL1 setting (integer) | Setpoint x 10^decimal. | UINT16 | Read/write | ||||
| HR | 309doc 40310 | Sensor 1 alarm AL2 setting (integer) | Setpoint x 10^decimal. | UINT16 | Read/write | ||||
| HR | 314doc 40315 | Sensor 1 full scale (integer) | Writable only with AI module allocation. | UINT16 | Read/write | ||||
| HR | 315doc 40316 | Sensor 1 decimal point (settings) | Writable only with AI module allocation. | UINT16 | Read/write | 0 = No decimal; 1 = 1 decimal place; 2 = 2 decimal places; 3 = 3 decimal places | |||
| HR | 318doc 40319 | Sensor 1 unit | Writable only with AI module allocation. | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | |||
| HR | 319doc 40320 | Sensor 1 alarm mode | UINT16 | Read | 0 = AL1 high / AL2 high; 1 = AL1 low / AL2 low; 2 = AL1 low / AL2 high | ||||
| HR | 336doc 40337 | Sensor 1 alarm delay AL1 | UINT16 | s | Read/write | ||||
| HR | 337doc 40338 | Sensor 1 alarm delay AL2 | UINT16 | s | Read/write | ||||
| HR | 349doc 40350 | DO module allocation | UINT16 | Read | 0 = Off; 1 = On | ||||
| HR | 350doc 40351 | 4-20 mA analog input allocation | UINT16 | Read | 0 = Off; 1 = On | ||||
| HR | 356doc 40357 | Sensor 1 sensor days of use | UINT16 | days | Read | ||||
| HR | 357doc 40358 | Sensor 1 pump days of use | UINT16 | days | Read | ||||
| HR | 358doc 40359 | Sensor 1 pump duty | Pump control value 0-100. | UINT16 | % | Read | |||
| HR | 382doc 40383 | Sensor 1 relay AL1 setting | UINT16 | Read/write | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 383doc 40384 | Sensor 1 relay AL2 setting | UINT16 | Read/write | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 384doc 40385 | Sensor 1 fault relay setting | UINT16 | Read/write | 0 = Normally not energized; 1 = Normally energized | ||||
| HR | 389doc 40390 | Sensor 1 maintenance mode | UINT16 | Read/write | 0 = Off; 1 = Maintenance mode 1; 2 = Maintenance mode 2 | ||||
| HR | 390doc 40391 | Sensor 1 alarm test on/off | UINT16 | Read/write | 0 = End alarm test; 1 = Start alarm test | ||||
| HR | 391doc 40392 | Sensor 1 alarm test concentration | Test value in %FS using the fixed-point setting. | UINT16 | Read/write | ||||
| HR | 2628doc 42629 | Sensor 1 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2629doc 42630 | Sensor 2 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2630doc 42631 | Sensor 3 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2631doc 42632 | Sensor 4 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2632doc 42633 | Sensor 5 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2633doc 42634 | Sensor 6 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2634doc 42635 | Sensor 7 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2635doc 42636 | Sensor 8 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2636doc 42637 | Sensor 9 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2637doc 42638 | Sensor 10 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2638doc 42639 | Sensor 11 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2639doc 42640 | Sensor 12 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2640doc 42641 | Sensor 13 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2641doc 42642 | Sensor 14 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2642doc 42643 | Sensor 15 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2643doc 42644 | Sensor 16 unit (grouped) | UINT16 | Read/write | 0 = No unit; 1 = ppm; 2 = ppb; 3 = vol%; 4 = %LEL; 5 = % | ||||
| HR | 2728doc 42729 | Sensor 1 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2729doc 42730 | Sensor 2 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2730doc 42731 | Sensor 3 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2731doc 42732 | Sensor 4 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2732doc 42733 | Sensor 5 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2733doc 42734 | Sensor 6 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2734doc 42735 | Sensor 7 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2735doc 42736 | Sensor 8 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2736doc 42737 | Sensor 9 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2737doc 42738 | Sensor 10 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2738doc 42739 | Sensor 11 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2739doc 42740 | Sensor 12 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2740doc 42741 | Sensor 13 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2741doc 42742 | Sensor 14 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2742doc 42743 | Sensor 15 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read | ||||
| HR | 2743doc 42744 | Sensor 16 concentration (integer, grouped) | Same value as the periodic block; scale by the decimal register. | UINT16 | Read |
Notes on this map
- All 32-bit items are left out: the status and fault-detail DWords (40001-40004 per channel), and every IEEE-754 float (40126-40249 block, float settings). The manual gives float examples as "upper word" / "lower word" without saying which register address each sits at, so the word order cannot be settled from the source.
- Character strings (serial number, tag and gas names) are also left out: the manual puts the 2nd character in the upper byte and the 1st in the lower byte, an order the string type here cannot express.
- Gas readings are integers: real value = raw / 10^decimal (decimal register 0-3). Example from the source: 20.9 vol% = 209 with decimal 1.
- The channel 1 settings block (40301-40397) repeats for channels 2-16 at +101 registers per channel (channel 2 starts at 40402). Grouped arrays for all 16 channels also exist at 42301-42984; only the concentration and unit arrays are listed here.
- Factory IP address is 192.168.0.101; the specification table allows at most 2 connected units. Writing to reserved or read-only registers is ignored; reading reserved registers returns 0.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP)
What Modbus registers does the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) have?
This map lists 117 registers: 117 holding registers. 34 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed as 40001-42984 with a relative (wire) address column; 40005 = relative address 4, confirmed by the function 03 example frame that reads 40005 with start address 0x0004.
What are the minimum Modbus registers to integrate the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP)?
Start with HR 4 Sensor 1 concentration (integer) (Sensor 1 concentration); HR 5 Sensor 1 decimal point (Sensor 1 decimal point); HR 6 Sensor 1 flow rate (Sensor 1 flow); HR 112 Heartbeat (Heartbeat); HR 113 Relay output monitor sensors 1/2 (Relay states sensors 1/2); HR 318 Sensor 1 unit (Sensor 1 unit).
How do I enable Modbus control of the New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP)?
Menu > Device Information > Modbus: select TCP/IP. Set IP and subnet (or DHCP) under Device Information.
Where is the official New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP) Modbus documentation?
The source is PS-8 Series Gas Detector Instruction Manual for Communication (GAE-180-00), revision 2024-12, published free by New Cosmos Electric at https://new-cosmos.co.jp/wp/wp-content/uploads/ind/ps8_signalsetting_manu_en.pdf.
More New Cosmos Electric Modbus register maps
Other gas detectors register maps
- Sensor (fixed gas detector)
Teledyne Detcon Model FP-700 catalytic bead combustible gas sensor (RS-485 Modbus)
Teledyne Detcon FP-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3168, Rev. 5.7.
Also known as: FP-700, Detcon FP-700, Teledyne Detcon FP-700 - Sensor (water leak detector)
Teracom TSF400-4 water-leak detector with Modbus RTU
TSF400-4 per the Teracom TSF400-4 user manual Revision R1.2.
Also known as: TSF400-4 - Sensor (extractive gas detector)
Honeywell Midas S2 extractive gas transmitter (Modbus/TCP)
Honeywell Midas S2 single-point extractive gas transmitters with Ethernet/PoE, user manual 3023M5001 Rev A, Modbus/TCP register map (Table 6-1).
Also known as: Midas S2, MIDAS-S2, Midas S2 gas detector - Sensor (fixed gas detector)
Teledyne Detcon Model DM-700 electrochemical toxic gas / oxygen sensor (RS-485 Modbus)
Teledyne Detcon DM-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3207, Rev. 5.9.
Also known as: DM-700, Detcon DM-700, Teledyne Detcon DM-700 - Sensor (fixed gas detector)
Teledyne Oldham Simtronics OLCT 700 / OLCT 710 FP catalytic bead combustible gas detector (RS-485 Modbus)
Teledyne Oldham Simtronics OLCT 700 and OLCT 710 FP detectors with 4-20 mA and RS-485 Modbus RTU, manual NP700FPIMEN Revision E.0.
Also known as: OLCT 700 FP, OLCT 710 FP, Oldham OLCT 700 FP, 700 FP series - Gas detection controller (sensor)
Gas Detection Australia GDA 4022
Gas Detection Australia 4022 two-sensor gas detection controller, Modbus document 4022 V4.2 Rev 2.0 (16/11/2022).
Also known as: 4022 V4.2, GDA-4022
All gas detectors Modbus register maps →
Source: PS-8 Series Gas Detector Instruction Manual for Communication · GAE-180-00 · rev. 2024-12. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.