- Home
- Modbus register maps
- Cummins
- PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)
Generator controller · Modbus register map
Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) Modbus register map
Updated 19 November 2026
PowerCommand 2.x/3.x are Cummins genset controls with a Modbus RTU slave port. Section 2 of the Cummins register mapping gives the switch position, active fault, genset AC metering and energy counters, engine data, and on PC 3.x also utility and genset-bus metering for paralleling. This map covers the monitoring block from 40010 to 40596 plus the Modbus remote start and fault reset.
This page lists 152 Modbus registers for the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) — 2 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Cummins’s own free documentation (linked below) and checked against it.
- Manufacturer
- Cummins
- Model
- PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)
- Equipment type
- Generator controller
- Registers
- 152 (2 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- PowerCommand 2.2, PowerCommand 2.3, PowerCommand 3.3, PC2.2, PC2.3, PC3.3
Integration notes: Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)
Poll 40010 (switch position), 40012/40013 (most recent fault and its type), 40018-40043 for genset AC values and 40061-40068 for engine data. Remote start is 40300 = 1 and fault reset 40301 = 1.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 9 | Control Switch Position | UINT16 | Control switch position | Read |
| HR 11 | Most Recent Fault or Warning | UINT16 | Most recent fault code | Read |
| HR 12 | Fault type of most recent fault | UINT16 | Fault type | Read |
| HR 24 | Genset LL Average Voltage | UINT16 | Average L-L voltage | Read |
| HR 28 | Genset Average Current | UINT16 | Average current | Read |
| HR 33 | Genset Total kW | INT16 | Total kW | Read |
| HR 67 | Average Engine Speed | UINT16 | Engine speed | Read |
| HR 299 | Remote Start Switch(Modbus) | UINT16 | Remote start | Read/write |
Enable Modbus control & writes
The section gives no enable parameter; the control's Modbus port settings are made at the control (see the control documentation).
Byte order & addressing
- 32-bit values are high word first (lower register = high word).
- Up to 40 contiguous registers per read or write.
- Gaps in the list are unused addresses.
Network setup
- Set the Modbus address and baud rate on the control; this document does not list them.
Watch out for
- Utility and genset-bus metering (40118-40199) exists only on PowerCommand 3.x.
Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 9doc 40010 | Control Switch Position | UINT16 | Read | 0 = Off; 1 = Auto; 2 = Manual | ||||
| HR | 11doc 40012 | Most Recent Fault or Warning | Most recent fault or warning code. | UINT16 | Read | ||||
| HR | 12doc 40013 | Fault type of most recent fault | UINT16 | Read | 0 = None; 1 = Warning; 2 = Shutdown | ||||
| HR | 13doc 40014 | Genset % Standby Total kW | INT16 | × 0.01 | % | Read | |||
| HR | 15doc 40016 | NFPA 110 Logical Status | NFPA 110 bit map, section 4 Table 4-1. | BITMAP16 | Read | ||||
| HR | 16doc 40017 | Extended NFPA 110 Logical Status | Extended annunciation bit map, Table 4-2. | BITMAP16 | Read | ||||
| HR | 17doc 40018 | Genset L1N Voltage | UINT16 | V | Read | ||||
| HR | 18doc 40019 | Genset L2N Voltage | UINT16 | V | Read | ||||
| HR | 19doc 40020 | Genset L3N Voltage | UINT16 | V | Read | ||||
| HR | 21doc 40022 | Genset L1L2 Voltage | UINT16 | V | Read | ||||
| HR | 22doc 40023 | Genset L2L3 Voltage | UINT16 | V | Read | ||||
| HR | 23doc 40024 | Genset L3L1 Voltage | UINT16 | V | Read | ||||
| HR | 24doc 40025 | Genset LL Average Voltage | UINT16 | V | Read | ||||
| HR | 25doc 40026 | Genset L1 Current | UINT16 | A | Read | ||||
| HR | 26doc 40027 | Genset L2 Current | UINT16 | A | Read | ||||
| HR | 27doc 40028 | Genset L3 Current | UINT16 | A | Read | ||||
| HR | 28doc 40029 | Genset Average Current | UINT16 | A | Read | ||||
| HR | 29doc 40030 | Genset Neutral Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 30doc 40031 | Genset L1 kW | INT16 | kW | Read | ||||
| HR | 31doc 40032 | Genset L2 kW | INT16 | kW | Read | ||||
| HR | 32doc 40033 | Genset L3 kW | INT16 | kW | Read | ||||
| HR | 33doc 40034 | Genset Total kW | INT16 | kW | Read | ||||
| HR | 34doc 40035 | Genset L1 kVAR | INT16 | kVAR | Read | ||||
| HR | 35doc 40036 | Genset L2 kVAR | INT16 | kVAR | Read | ||||
| HR | 36doc 40037 | Genset L3 kVAR | INT16 | kVAR | Read | ||||
| HR | 37doc 40038 | Genset Total kVAR | INT16 | kVAR | Read | ||||
| HR | 39doc 40040 | Genset L1 kVA | UINT16 | kVA | Read | ||||
| HR | 40doc 40041 | Genset L2 kVA | UINT16 | kVA | Read | ||||
| HR | 41doc 40042 | Genset L3 kVA | UINT16 | kVA | Read | ||||
| HR | 42doc 40043 | Genset Total kVA | UINT16 | kVA | Read | ||||
| HR | 45doc 40046-40047 | Genset Total Negative kWh | UINT32 | ABCD | kWh | Read | |||
| HR | 47doc 40048-40049 | Genset Total Positive kWh | UINT32 | ABCD | kWh | Read | |||
| HR | 49doc 40050-40051 | Genset Total Net kWh | INT32 | ABCD | kWh | Read | |||
| HR | 51doc 40052-40053 | Genset Total Negative kVARh | UINT32 | ABCD | kVARh | Read | |||
| HR | 53doc 40054-40055 | Genset Total Positive kVARh | UINT32 | ABCD | kVARh | Read | |||
| HR | 57doc 40058 | Genset % Standby L1 Current | UINT16 | × 0.1 | % | Read | |||
| HR | 58doc 40059 | Genset % Standby L2 Current | UINT16 | × 0.1 | % | Read | |||
| HR | 59doc 40060 | Genset % Standby L3 Current | UINT16 | × 0.1 | % | Read | |||
| HR | 60doc 40061 | Battery Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 61doc 40062 | Oil Pressure | UINT16 | kPa | Read | ||||
| HR | 62doc 40063 | Oil Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 63doc 40064 | Coolant Temperature | INT16 | × 0.1 | °C | Read | |||
| HR | 64doc 40065 | Intake Manifold Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 65doc 40066 | Fuel Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 66doc 40067 | Fuel Rate | UINT16 | × 0.05 | gal/hr | Read | |||
| HR | 67doc 40068 | Average Engine Speed | UINT16 | rpm | Read | ||||
| HR | 69doc 40070-40071 | Engine Running Time | UINT32 | ABCD | × 0.1 | s | Read | ||
| HR | 71doc 40072-40073 | Total Fuel Consumption | UINT32 | ABCD | × 0.1 | gal | Read | ||
| HR | 73doc 40074-40075 | Total Number of Runs | UINT32 | ABCD | Read | ||||
| HR | 117doc 40118 | Utility L1N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 118doc 40119 | Utility L2N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 119doc 40120 | Utility L3N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 121doc 40122 | Utility L1L2 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 122doc 40123 | Utility L2L3 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 123doc 40124 | Utility L3L1 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 124doc 40125 | Utility LL Average Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 125doc 40126 | Utility L1 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 126doc 40127 | Utility L2 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 127doc 40128 | Utility L3 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 130doc 40131 | Utility L1 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 131doc 40132 | Utility L2 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 132doc 40133 | Utility L3 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 133doc 40134 | Utility Total kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 134doc 40135 | Utility L1 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 135doc 40136 | Utility L2 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 136doc 40137 | Utility L3 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 137doc 40138 | Utility Total kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 139doc 40140 | Utility L1 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 140doc 40141 | Utility L2 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 141doc 40142 | Utility L3 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 142doc 40143 | Utility Total kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 143doc 40144-40145 | Utility Frequency | PC 3.x only. | UINT32 | ABCD | × 0.001 | Hz | Read | |
| HR | 145doc 40146-40147 | Utility Total Negative kWh | PC 3.x only. | UINT32 | ABCD | kWh | Read | ||
| HR | 147doc 40148-40149 | Utility Total Positive kWh | PC 3.x only. | UINT32 | ABCD | kWh | Read | ||
| HR | 149doc 40150-40151 | Utility Total Net kWh | PC 3.x only. | INT32 | ABCD | kWh | Read | ||
| HR | 151doc 40152-40153 | Utility Total Negative kVARh | PC 3.x only. | UINT32 | ABCD | kVARh | Read | ||
| HR | 153doc 40154-40155 | Utility Total Positive kVARh | PC 3.x only. | UINT32 | ABCD | kVARh | Read | ||
| HR | 155doc 40156-40157 | Utility Total Net kVARh | PC 3.x only. | INT32 | ABCD | kVARh | Read | ||
| HR | 157doc 40158 | Genset Bus L1N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 158doc 40159 | Genset Bus L2N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 159doc 40160 | Genset Bus L3N Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 161doc 40162 | Genset Bus L1L2 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 162doc 40163 | Genset Bus L2L3 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 163doc 40164 | Genset Bus L3L1 Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 164doc 40165 | Genset Bus LL Average Voltage | PC 3.x only. | UINT16 | V | Read | |||
| HR | 165doc 40166 | Genset Bus L1 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 166doc 40167 | Genset Bus L2 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 167doc 40168 | Genset Bus L3 Current | PC 3.x only. | UINT16 | A | Read | |||
| HR | 170doc 40171 | Genset Bus L1 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 171doc 40172 | Genset Bus L2 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 172doc 40173 | Genset Bus L3 kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 173doc 40174 | Genset Bus Total kW | PC 3.x only. | INT16 | kW | Read | |||
| HR | 174doc 40175 | Genset Bus L1 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 175doc 40176 | Genset Bus L2 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 176doc 40177 | Genset Bus L3 kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 177doc 40178 | Genset Bus Total kVAR | PC 3.x only. | INT16 | kVAR | Read | |||
| HR | 179doc 40180 | Genset Bus L1 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 180doc 40181 | Genset Bus L2 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 181doc 40182 | Genset Bus L3 kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 182doc 40183 | Genset Bus Total kVA | PC 3.x only. | UINT16 | kVA | Read | |||
| HR | 183doc 40184-40185 | Genset Bus Frequency | PC 3.x only. | UINT32 | ABCD | × 0.001 | Hz | Read | |
| HR | 185doc 40186-40187 | Genset Bus Total Negative kWh | PC 3.x only. | UINT32 | ABCD | kWh | Read | ||
| HR | 187doc 40188-40189 | Genset Bus Total Positive kWh | PC 3.x only. | UINT32 | ABCD | kWh | Read | ||
| HR | 189doc 40190-40191 | Genset Bus Total Net kWh | PC 3.x only. | INT32 | ABCD | kWh | Read | ||
| HR | 191doc 40192-40193 | Genset Bus Total Negative kVARh | PC 3.x only. | UINT32 | ABCD | kVARh | Read | ||
| HR | 193doc 40194-40195 | Genset Bus Total Positive kVARh | PC 3.x only. | UINT32 | ABCD | kVARh | Read | ||
| HR | 195doc 40196-40197 | Genset Bus Total Net kVARh | PC 3.x only. | INT32 | ABCD | kVARh | Read | ||
| HR | 197doc 40198 | Ground Current | PC 3.x only. | UINT16 | × 0.1 | A | Read | ||
| HR | 198doc 40199 | Genset Negative Sequence Current % | PC 3.x only. | UINT16 | × 0.01 | % | Read | ||
| HR | 200doc 40201 | Coolant Temperature Sensor Type | UINT16 | Read | 0 = PGBU; 1 = EBU | ||||
| HR | 206doc 40207 | Battery Charger Alternator Flash Voltage | UINT16 | × 0.001 | V | Read | |||
| HR | 209doc 40210 | External Speed Bias Input | INT16 | × 0.01 | % | Read | |||
| HR | 210doc 40211 | External Voltage Bias Input | INT16 | × 0.01 | % | Read | |||
| HR | 225doc 40226 | Speed Bias Output / Configurable Analog output #1 Output Predictor | PC 3.x only. | INT16 | × 0.01 | V | Read | ||
| HR | 226doc 40227 | Voltage Bias Output / Configurable Analog output #2 Output Predictor | PC 3.x only. | INT16 | × 0.01 | V | Read | ||
| HR | 227doc 40228 | Amber Warning Lamp Status | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 228doc 40229 | Barometric absolute pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 229doc 40230 | Boost Pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 230doc 40231 | CAN Datalink Status | UINT16 | Read | 0 = Inactive; 1 = Active; 2 = Failed | ||||
| HR | 231doc 40232 | Crankcase Pressure | INT16 | × 0.1 | psi | Read | |||
| HR | 234doc 40235 | ECM Derate Request | UINT16 | Read | 0 = No Derate Request; 1 = Derate Request; 2 = Error; 3 = Don’t Care | ||||
| HR | 235doc 40236 | Engine Application Type | UINT16 | Read | 0 = ECM; 1 = Hydro-Mechanical | ||||
| HR | 241doc 40242 | Aftercooler Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 253doc 40254 | Fuel Supply Pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 257doc 40258-40259 | Fuel Outlet Pressure | UINT32 | ABCD | × 0.1 | psi | Read | ||
| HR | 259doc 40260 | Intake Manifold 2 Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 260doc 40261 | Intake Manifold 3 Temperature | INT16 | × 0.1 | °F | Read | |||
| HR | 263doc 40264 | Percent Engine Torque/Duty Cycle | INT16 | % | Read | ||||
| HR | 275doc 40276 | Post-Filter Oil Pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 276doc 40277 | Pre-Filter Oil Pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 277doc 40278 | Configurable Input #14 Switch | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 278doc 40279-40280 | Turbocharger 1 Speed | UINT32 | ABCD | rpm | Read | |||
| HR | 280doc 40281 | Turbocharger 2 Boost Pressure | UINT16 | × 0.1 | psi | Read | |||
| HR | 281doc 40282 | Water in Fuel Indicator | UINT16 | Read | 0 = No; 1 = Yes | ||||
| HR | 282doc 40283 | Controller Mode | UINT16 | Read | 0 = Off; 1 = Ready; 2 = Setup; 3 = Starting; 4 = Idle; 5 = Rated; 6 = Stop Normal; 7 = Stop Emergency; 8 = Factory Test; 9 = Wait to Power Down | ||||
| HR | 284doc 40285 | Power Down Mode Timer | UINT16 | s | Read | ||||
| HR | 297doc 40298-40299 | Runs Since Reset | UINT32 | ABCD | Read | ||||
| HR | 299doc 40300 | Remote Start Switch(Modbus) | Write 1 to start the genset remotely, 0 to release. | UINT16 | Read/write | 0 = Inactive; 1 = Active | |||
| HR | 300doc 40301 | Fault Reset (Modbus) | Write 1 to reset faults. | UINT16 | Read/write | 0 = Inactive; 1 = Active | |||
| HR | 499doc 40500 | Low Fuel Switch | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 500doc 40501 | Low Fuel/Configurable Input #6 Switch | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 508doc 40509 | PTC Mode Switch | PC 3.x only. | UINT16 | Read | 0 = Inactive; 1 = Active | |||
| HR | 509doc 40510 | Extended Parallel/Configurable Input #32 Switch | PC 3.x only. | UINT16 | Read | 0 = Inactive; 1 = Active | |||
| HR | 564doc 40565 | Common Warning Event Status | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 569doc 40570 | Fault Reset Command | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 576doc 40577-40578 | Base Frequency | UINT32 | ABCD | × 0.001 | Hz | Read | ||
| HR | 585doc 40586 | Excitation State | UINT16 | Read | 0 = Disabled; 1 = Enabled | ||||
| HR | 586doc 40587 | Exercise Command | UINT16 | Read | 0 = Inactive; 1 = Active; 2 = Reserved; 3 = Not Available | ||||
| HR | 588doc 40589 | Exercise Time Remaining | UINT16 | × 0.1 | h | Read | |||
| HR | 591doc 40592 | Battle Short Command | UINT16 | Read | 0 = Inactive; 1 = Active | ||||
| HR | 594doc 40595-40596 | Final Frequency Reference | UINT32 | ABCD | × 0.001 | Hz | Read | ||
| HR | 40055doc 40056-40057 | Genset Total Net kVARh | INT32 | ABCD | kVARh | Read |
Notes on this map
- Cummins does not host this document publicly; the link is a copy on an integrator's site (Control Concepts). A dealer site lists a newer Issue 26 (2020) that could not be downloaded here; registers may have been added since Issue 7.
- 32-bit values use two rows in the table; section 2 says the lower register is the high word and gives value = high x 65536 x multiplier + low x multiplier, with the engine running time example on 40070/40071. They are mapped as one 32-bit value, high word first (ABCD).
- Each row gives multiplier, offset, size in bits and sign; types and scales here follow those columns. Power factors 40039/40139/40179 are 8-bit signed values in a 16-bit register and are left out because the manual does not say which byte holds them.
- Left out: the fault-text string blocks (40320-40379), the reset-time arrays (40076-40112), configurable input text (40600+) and everything from 40600 upward (setpoints, adjustments and the 43xxx/45xxx parameter blocks).
- The NFPA 110 (40016) and extended annunciation (40017) bit tables label bit 0 as the MSB, which conflicts with other sections of the same document, so bits are not expanded.
- Temperatures are mostly in °F (0.1 °F) except coolant (0.1 °C), as printed.
- Older control software may not support every register; an unsupported register may simply not answer.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)
What Modbus registers does the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) have?
This map lists 152 registers: 152 holding registers. 2 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed as Modicon 4xxxx holding-register numbers; 40010 is wire address 9.
What byte order does the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)?
Start with HR 9 Control Switch Position (Control switch position); HR 11 Most Recent Fault or Warning (Most recent fault code); HR 12 Fault type of most recent fault (Fault type); HR 24 Genset LL Average Voltage (Average L-L voltage); HR 28 Genset Average Current (Average current); HR 33 Genset Total kW (Total kW); HR 67 Average Engine Speed (Engine speed); HR 299 Remote Start Switch(Modbus) (Remote start).
How do I enable Modbus control of the Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU)?
The section gives no enable parameter; the control's Modbus port settings are made at the control (see the control documentation).
Where is the official Cummins PowerCommand 2.2 / 2.3 / 3.3 genset control (Modbus RTU) Modbus documentation?
The source is Modbus Register Mapping (PCC 1301, PowerCommand 1.1/1.2/2.2/2.3/3.3, DMC 1000/1500, MCM3320) (A029X159 Issue 7), revision 2012-04. Cummins doesn't publish it on its own website, so this map was re-typed from a free copy at https://ccontrols.com/support/dp/modbus2300.pdf. It may be an older revision, so check it against the live unit.
More Cummins Modbus register maps
- Generator controller (paralleling master control)
Cummins MCM3320 master control module (Modbus RTU)
Cummins MCM3320 master control modules on their RS-485 Modbus RTU port, per section 10 of A029X159 Issue 7.
Also known as: MCM3320, MCM 3320, PowerCommand MCM3320 - Generator controller
Cummins PCC 1301 / PowerCommand 1.1 / 1.2 genset control (Modbus RTU)
Cummins PCC 1301 and PowerCommand 1.1/1.2 generator set controls on their RS-485 Modbus RTU port, per section 1 of A029X159 Issue 7.
Also known as: PCC 1301, PCC1301, PowerCommand 1.1, PowerCommand 1.2, PC1.1, PC1.2
Other generator controllers register maps
- Generator controller
DEIF AGC-4 Mk II Automatic Genset Controller
AGC-4 Mk II software 6.31.0 (Modbus tables revision N), genset (GEN) application only.
Also known as: AGC-4 Mk2, AGC-4 MkII - Transfer switch
Kohler Decision-Maker MPAC 750/1200/1500 ATS controller
Kohler Decision-Maker MPAC 750, 1200 and 1500 ATS controllers, Modbus RTU on the logic board RS-485 port or Modbus TCP, per section 14 of TP-6113.
Also known as: Decision-Maker MPAC 750, Decision-Maker MPAC 1200, Decision-Maker MPAC 1500, DM MPAC - Generator controller
Lovato Electric RGK700SA stand-alone genset controller
RGK700SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 700SA, RGK700 SA - Generator controller
SmartGen HGM4010N / HGM4020N
HGM4010N (auto start) and HGM4020N (AMF) genset controllers, HGM4000N communication protocol v1.2.
Also known as: HGM4010N, HGM4000N - Generator controller
Woodward easYgen-3000XT Series
easYgen-3100XT-P1 / 3200XT-P1 / 3200XT-P1-LT, release 2.17-0, default Modbus data protocol 5010 (Basic Visualization).
Also known as: easYgen-3100XT-P1, easYgen-3200XT-P1, easYgen-3200XT-P1-LT, easYgen-3100XT, easYgen-3200XT - Generator controller
DEIF AGC-4 Automatic Genset Controller
AGC-4 software 4.83.0 (Modbus tables revision I), genset (DG) application; mains and BTB variants share many addresses but are not covered.
Also known as: AGC-4 DG, AGC 4, Multi-line 2 AGC-4
All generator controllers Modbus register maps →
Source: Modbus Register Mapping (PCC 1301, PowerCommand 1.1/1.2/2.2/2.3/3.3, DMC 1000/1500, MCM3320) · A029X159 Issue 7 · rev. 2012-04 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.