- Home
- Modbus register maps
- Panasonic
- KW8M Eco-POWER METER
Energy meter · Modbus register map
Panasonic KW8M Eco-POWER METER Modbus register map
Updated 17 November 2026
The KW8M is a panel-mount energy meter for single- and three-phase circuits with a pulse counter input and an RS485 port running MEWTOCOL or Modbus RTU. Holding registers carry energy, current, voltage, power, PF, frequency, load on/off hours and pulse counts; the AKW8111H adds demand values and logging. This map covers the common table and the H-only demand and status registers.
This page lists 41 Modbus registers for the Panasonic KW8M Eco-POWER METER — 27 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Panasonic’s own free documentation (linked below) and checked against it.
- Manufacturer
- Panasonic
- Model
- KW8M Eco-POWER METER
- Equipment type
- Energy meter
- Registers
- 41 (27 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 19200 baud, 8O1
- Documented addressing
- hexadecimal, 0-based
- 32-bit word order
- CDAB low word first (word-swapped)
- Also known as
- AKW8111, AKW8111H
Integration notes: Panasonic KW8M Eco-POWER METER
Switch the protocol to MODBUS(RTU) in Mode 3, then poll with function 03: 0064H energy (2 words, 0.01 kWh), 00B0H active power, 006BH-006DH currents, 00AAH-00AEH voltages, 006FH PF and 0070H frequency.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 100 | Integral active energy | UINT32 CDAB | Integral active energy | Read/write |
| HR 176 | Instantaneous active power | UINT32 CDAB | Active power | Read |
| HR 107 | Current L1 (CT1) | UINT16 | Current L1 | Read |
| HR 170 | Voltage L1 (P1-P0) | UINT32 CDAB | Voltage L1 | Read |
| HR 111 | Power factor | INT16 | Power factor | Read |
| HR 112 | Frequency | UINT16 | Frequency | Read |
Enable Modbus control & writes
Protocol defaults to MEWTOCOL; change it to MODBUS(RTU) in setting Mode 3 together with station number, speed, format and response time.
Byte order & addressing
- Modbus RTU only works with the 8-bit formats; the default format 8bit-o is odd parity.
- Out-of-range writes are acknowledged but ignored.
Network setup
- Defaults: station 1, 19200 bps, 8bit-o, response time 5 ms.
- Set phase/wire, CT type and voltage range in Mode 1 before reading values.
Watch out for
- AKW8111H: switch the backup battery ON and initialise the main-unit memory (Mode 4) after setting the calendar timer (Mode 5), or log data may be wrong.
- Settings written over Modbus are stored in EEPROM; avoid cyclic writes.
Panasonic KW8M Eco-POWER METER Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 1doc 0001H | Contact output status | AKW8111H only. | UINT16 | Read | 0 = Off; 1 = On | |||
| HR | 48doc 0030H | Hysteresis for demand alarm off | AKW8111H only. | UINT16 | % | Read/write | |||
| HR | 49doc 0031H | Demand monitor start time | AKW8111H only. 1-30. | UINT16 | min | Read/write | |||
| HR | 50doc 0032H | Rate | Electricity rate per kWh used for the charge display. | UINT16 | × 0.01 | Read/write | |||
| HR | 60doc 003CH | CT type | Dedicated CT rating: 5, 50, 100, 250, 400 or 600. | UINT16 | A | Read/write | |||
| HR | 61doc 003DH | Unit for pulse output | UINT32 | CDAB | Read/write | 1 = 0.001 kWh; 10 = 0.01 kWh; 100 = 0.1 kWh; 222 = Demand alarm (00CDH); 333 = Stand-by alarm (004DH/004EH); 555 = Preset count output (preset 009EH); 777 = Current alarm (ratio 0045H); 999 = Power alarm (alarm value 0040H); 1000 = 1 kWh; 10000 = 10 kWh; 100000 = 100 kWh | |||
| HR | 63doc 003FH | CT primary current (5 A CT) | For a commercial 5 A secondary CT, 1-4000. | UINT16 | A | Read/write | |||
| HR | 64doc 0040H | Alarm value (instantaneous active power) | UINT32 | CDAB | × 0.01 | kW | Read/write | ||
| HR | 66doc 0042H | VT ratio | UINT16 | × 0.01 | Read/write | ||||
| HR | 67doc 0043H | Current threshold for time measurement | Load on/off-time threshold. | UINT16 | × 0.1 | % | Read/write | ||
| HR | 68doc 0044H | Cut-off current | UINT16 | × 0.1 | % | Read/write | |||
| HR | 69doc 0045H | Current alarm value | UINT16 | × 0.1 | % | Read/write | |||
| HR | 70doc 0046H | Voltage range | UINT16 | Read/write | 1 = 400 V; 2 = 200 V | ||||
| HR | 77doc 004DH | Current ratio for stand-by alarm | UINT16 | × 0.1 | % | Read/write | |||
| HR | 78doc 004EH | Time for stand-by alarm | 1-9999; unit not printed in the table. | UINT16 | Read/write | ||||
| HR | 80doc 0050H | SRAM initialize | AKW8111H only. | UINT16 | Read/write | 0 = Off; 1 = On | |||
| HR | 98doc 0062H | Active energy for arbitrary period | AKW8111H only. Table unit reads 0.01kW. | UINT32 | CDAB | × 0.01 | Read/write | ||
| HR | 100doc 0064H | Integral active energy | UINT32 | CDAB | × 0.01 | kWh | Read/write | ||
| HR | 102doc 0066H | Integral reactive energy | UINT32 | CDAB | × 0.01 | kvarh | Read/write | ||
| HR | 104doc 0068H | Integral apparent energy | UINT32 | CDAB | × 0.01 | kVAh | Read/write | ||
| HR | 107doc 006BH | Current L1 (CT1) | UINT16 | × 0.1 | A | Read | |||
| HR | 108doc 006CH | Current L2 (CT2) | UINT16 | × 0.1 | A | Read | |||
| HR | 109doc 006DH | Current L3 (CT3) | UINT16 | × 0.1 | A | Read | |||
| HR | 111doc 006FH | Power factor | INT16 | × 0.01 | Read | ||||
| HR | 112doc 0070H | Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 150doc 0096H | Load ON-time | UINT32 | CDAB | × 0.1 | h | Read/write | ||
| HR | 152doc 0098H | Load OFF-time | UINT32 | CDAB | × 0.1 | h | Read/write | ||
| HR | 154doc 009AH | Pulse count value | UINT32 | CDAB | Read/write | ||||
| HR | 158doc 009EH | Preset value | Pulse count preset for the count output. | UINT32 | CDAB | Read/write | |||
| HR | 160doc 00A0H | Prescale value | UINT32 | CDAB | × 0.001 | Read/write | |||
| HR | 162doc 00A2H | Max. counting speed | UINT16 | Hz | Read/write | 30 = 30 Hz; 2000 = 2000 Hz | |||
| HR | 163doc 00A3H | Auto-off time | UINT16 | min | Read/write | ||||
| HR | 170doc 00AAH | Voltage L1 (P1-P0) | UINT32 | CDAB | × 0.1 | V | Read | ||
| HR | 172doc 00ACH | Voltage L2 (P2-P0) | UINT32 | CDAB | × 0.1 | V | Read | ||
| HR | 174doc 00AEH | Voltage L3 (P3-P0) | UINT32 | CDAB | × 0.1 | V | Read | ||
| HR | 176doc 00B0H | Instantaneous active power | UINT32 | CDAB | × 0.01 | kW | Read | ||
| HR | 178doc 00B2H | Instantaneous reactive power | INT32 | CDAB | × 0.01 | kvar | Read | ||
| HR | 180doc 00B4H | Instantaneous apparent power | UINT32 | CDAB | × 0.01 | kVA | Read | ||
| HR | 200doc 00C8H | Present demand | AKW8111H only. | UINT32 | CDAB | × 0.01 | kW | Read | |
| HR | 203doc 00CBH | Estimated demand | AKW8111H only. | UINT32 | CDAB | × 0.01 | kW | Read | |
| HR | 205doc 00CDH | Demand setting value | AKW8111H only. | UINT32 | CDAB | × 0.01 | kW | Read/write |
Notes on this map
- Word order: every 32-bit row is printed as two registers marked <LSB> (lower address) and <MSB> (higher address), so the low word comes first (CDAB).
- The 'integral active power for arbitrary period' row (0062H) prints its unit as 0.01kW; it is listed without a unit.
- Left out: the AKW8111H log-data block (4E20H onward and F6CCH onward) and calendar-timer settings, which are log records rather than live values.
- Registers not listed read 0.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Panasonic KW8M Eco-POWER METER
What Modbus registers does the Panasonic KW8M Eco-POWER METER have?
This map lists 41 registers: 41 holding registers. 27 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Panasonic KW8M Eco-POWER METER Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The table prints hex data items (0064H) that go into the request unchanged; the manual's example resets energy by writing 2 words at 0064H. The MEWTOCOL DT number in decimal equals the hex Modbus address.
What byte order does the Panasonic KW8M Eco-POWER METER use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Panasonic KW8M Eco-POWER METER?
Start with HR 100 Integral active energy (Integral active energy); HR 176 Instantaneous active power (Active power); HR 107 Current L1 (CT1) (Current L1); HR 170 Voltage L1 (P1-P0) (Voltage L1); HR 111 Power factor (Power factor); HR 112 Frequency (Frequency).
How do I enable Modbus control of the Panasonic KW8M Eco-POWER METER?
Protocol defaults to MEWTOCOL; change it to MODBUS(RTU) in setting Mode 3 together with station number, speed, format and response time.
Where is the official Panasonic KW8M Eco-POWER METER Modbus documentation?
The source is KW8M Eco-POWER METER User's Manual (ARCT1F440E-8), revision 2016-08, published free by Panasonic at https://mediap.industry.panasonic.eu/assets/custom-upload/Factory%20%26%20Automation/Eco-POWER%20METERS/Manuals/mn_kw8m_user_pidsx_en.pdf.
More Panasonic Modbus register maps
- Heat pump (air-to-water) Modbus interface
Panasonic CZ-NSMB A2W Modbus PCB for Aquarea air-to-water heat pumps
Panasonic CZ-NSMB Modbus PCB fitted inside Panasonic Air-To-Water control boxes; the manual's compatibility list names the A2W M-Series control module WH-CME8 and the Big A2W 20-30 kW outdoor units WH-WXG20/25/30ME8 with control module WH-CME8L (user manual M02412F0). Some registers carry H/J/K/L-series conditions.
Also known as: CZ-NSMB, A2W Modbus PCB, WH-CME8, WH-CME8L, WH-WXG20ME8, WH-WXG25ME8, WH-WXG30ME8, Aquarea M series Modbus, Big A2W Modbus - Energy meter
Panasonic KW7M Eco-POWER METER
Panasonic KW7M (AKW7111 / AKW7111B) with Modbus RTU selected, user manual ARCT1F434E-6.
Also known as: AKW7111, AKW7111B - Energy meter (multi-circuit power monitor)
Panasonic KW9M Eco-POWER METER
Panasonic KW9M (AKW91110) with the Modbus RTU protocol selected, user manual WUME-KW9M-10.
Also known as: AKW91110
Other power & energy meters register maps
- Energy meter (DC)
Rishabh Instruments RISH DC2111 MOD single-channel DC energy meter
Rishabh RISH DC2111 MOD single-channel DC energy meters with RS-485 Modbus, per interface definition DMAN-00IM-1669 Rev. D (08/25).
Also known as: RISH DC2111 MOD, DC2111 - Energy meter
Rishabh Instruments RISH ED21XX / EC21XX / ER21XX single-phase energy meters
Rishabh RISH ED21XX (direct), EC21XX (CT) and ER21XX (RJ12 CT) single-phase meters in their Modbus versions, per operating manual DMAN-00IM-1073 Rev. M.
Also known as: RISH ED21X1, RISH EC21X1, RISH ER21X1, RISH ED21XX, RISH EC21XX, RISH ER21XX - Power meter
Rishabh Instruments RISH LM 1340 multifunction meter
Rishabh RISH LM 1340 panel multifunction instruments with RS-485 Modbus, per interface definition DMAN-00IM-0923 Rev. D (03/2026).
Also known as: RISH LM 1340, LM1340 - Power meter (power factor controller)
Rishabh Instruments RISH PFC 96 / PFC 144 automatic power factor controller
Rishabh RISH PFC 96 and PFC 144 automatic power factor (APFC) controllers with RS-485 Modbus RTU, per interface definition version D (12/18).
Also known as: RISH PFC 96, RISH PFC 144, PFC96, PFC144, RISH PFC-12, APFC - Power meter (power quality analyzer)
SATEC PM175 powermeter and power quality analyzer
SATEC PM175 from firmware 25.2.6, per Modbus reference guide BG0416 Rev. A7 (Nov 2009).
Also known as: PM175, SATEC PM175, PM 175 - Energy meter
Senva EM-RS485 networked energy meter (Modbus RTU/ASCII)
Senva EM-RS485 three-phase energy meters with Senva CVT sensors, firmware v1.1.2, Modbus Protocol Guide 154-0023-0B (2017-04-10).
Also known as: EM-RS485, Senva EM-RS485, Senva protocol energy meter
All power & energy meters Modbus register maps →
Source: KW8M Eco-POWER METER User's Manual · ARCT1F440E-8 · rev. 2016-08. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.