- Home
- Modbus register maps
- Eastron
- SDM230-Modbus
Energy meter · Modbus register map
Eastron SDM230-Modbus Modbus register map
Updated 17 November 2026
The SDM230-Modbus is a single-phase, two-module DIN-rail kWh meter with an RS485 Modbus RTU port and two tariffs. Live values and energy counters, including per-tariff energy and maximum demand, are IEEE-754 floats in input register pairs (function 04). Holding registers cover address, baud, parity, pulse output and the energy measurement mode.
This page lists 53 Modbus registers for the Eastron SDM230-Modbus — 9 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Eastron’s own free documentation (linked below) and checked against it.
- Manufacturer
- Eastron
- Model
- SDM230-Modbus
- Equipment type
- Energy meter
- Registers
- 53 (9 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- SDM230Modbus, SDM230-2T, SDM230-M
Integration notes: Eastron SDM230-Modbus
Read input registers with function 04 in two-register pairs; values are floats, high word first. Voltage is 0x0000, current 0x0006, power 0x000C, import kWh 0x0048 and total kWh 0x0156. Tariff energy starts at 0x130C.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | Voltage | FLOAT32 ABCD | Voltage | Read |
| IR 6 | Current | FLOAT32 ABCD | Current | Read |
| IR 12 | Active power | FLOAT32 ABCD | Active power | Read |
| IR 30 | Power factor | FLOAT32 ABCD | Power factor | Read |
| IR 70 | Frequency of supply voltages | FLOAT32 ABCD | Frequency | Read |
| IR 72 | Import active energy since last reset | FLOAT32 ABCD | Import kWh | Read |
| IR 342 | Total active energy | FLOAT32 ABCD | Total kWh | Read |
Enable Modbus control & writes
Modbus RTU is always active on the RS485 terminals; no enable step is documented.
Byte order & addressing
- 4xxxx settings are two-register floats written with function 16; the F9xx settings are single 16-bit hex values.
- Total energy depends on Measurement mode (463777): import only, import + export (default) or import - export.
Network setup
- Defaults: address 1, 9600 baud, no parity, 1 stop bit.
- Baud rates 1200, 2400, 4800 and 9600 are selectable.
Watch out for
- Read floats on even start addresses with even register counts or the meter returns an exception.
Eastron SDM230-Modbus Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 | Voltage | FLOAT32 | ABCD | V | Read | |||
| IR | 6doc 30007 | Current | FLOAT32 | ABCD | A | Read | |||
| IR | 12doc 30013 | Active power | FLOAT32 | ABCD | W | Read | |||
| IR | 18doc 30019 | Apparent power | FLOAT32 | ABCD | VA | Read | |||
| IR | 24doc 30025 | Reactive power | FLOAT32 | ABCD | VAr | Read | |||
| IR | 30doc 30031 | Power factor | FLOAT32 | ABCD | Read | ||||
| IR | 36doc 30037 | Phase angle | FLOAT32 | ABCD | ° | Read | |||
| IR | 70doc 30071 | Frequency of supply voltages | FLOAT32 | ABCD | Hz | Read | |||
| IR | 72doc 30073 | Import active energy since last reset | FLOAT32 | ABCD | kWh | Read | |||
| IR | 74doc 30075 | Export active energy since last reset | FLOAT32 | ABCD | kWh | Read | |||
| IR | 76doc 30077 | Import reactive energy since last reset | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 78doc 30079 | Export reactive energy since last reset | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 84doc 30085 | Active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 86doc 30087 | Max active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 88doc 30089 | Import active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 90doc 30091 | Max import active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 92doc 30093 | Export active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 94doc 30095 | Max export active power demand | FLOAT32 | ABCD | W | Read | |||
| IR | 258doc 30259 | Current demand | FLOAT32 | ABCD | A | Read | |||
| IR | 264doc 30265 | Max current demand | FLOAT32 | ABCD | A | Read | |||
| IR | 342doc 30343 | Total active energy | Per the Measurement mode setting (default import + export). | FLOAT32 | ABCD | kWh | Read | ||
| IR | 344doc 30345 | Total reactive energy | Per the Measurement mode setting (default import + export). | FLOAT32 | ABCD | kVArh | Read | ||
| IR | 384doc 30385 | Current resettable total active energy | FLOAT32 | ABCD | kWh | Read | |||
| IR | 386doc 30387 | Current resettable total reactive energy | Unit printed as kWh in the source although this is a reactive energy value. | FLOAT32 | ABCD | kWh | Read | ||
| IR | 4876doc 34877 | Total active Energy Rate 1 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4878doc 34879 | Total active Energy Rate 2 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4884doc 34885 | Import active Energy Rate 1 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4886doc 34887 | Import active Energy Rate 2 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4892doc 34893 | Export active Energy Rate 1 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4894doc 34895 | Export active Energy Rate 2 | FLOAT32 | ABCD | kWh | Read | |||
| IR | 4900doc 34901 | Total reactive Energy Rate 1 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 4902doc 34903 | Total reactive Energy Rate 2 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 4908doc 34909 | Import reactive Energy Rate 1 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 4910doc 34911 | Import reactive Energy Rate 2 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 4916doc 34917 | Export reactive Energy Rate 1 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 4918doc 34919 | Export reactive Energy Rate 2 | FLOAT32 | ABCD | kVArh | Read | |||
| IR | 5074doc 35075 | Maximum system positive active power demand of tariff 1 | FLOAT32 | ABCD | kW | Read | |||
| IR | 5076doc 35077 | Maximum system positive active power demand of tariff 2 | FLOAT32 | ABCD | kW | Read | |||
| IR | 5204doc 35205 | Maximum system reverse active power demand of tariff 1 | FLOAT32 | ABCD | kW | Read | |||
| IR | 5206doc 35207 | Maximum system reverse active power demand of tariff 2 | FLOAT32 | ABCD | kW | Read | |||
| IR | 5472doc 35473 | Tariff1 total active Maximum Power Demand | FLOAT32 | ABCD | W | Read | |||
| IR | 5478doc 35479 | Tariff 1 L1 Maximum Current Demand | FLOAT32 | ABCD | A | Read | |||
| IR | 5486doc 35487 | Tariff 2 total active Maximum Power Demand | FLOAT32 | ABCD | W | Read | |||
| IR | 5492doc 35493 | Tariff 2 L1 Maximum Current Demand | FLOAT32 | ABCD | A | Read | |||
| HR | 12doc 40013 | Pulse output 1 width | 60, 100 or 200 ms (default 100). | FLOAT32 | ABCD | ms | Read/write | ||
| HR | 18doc 40019 | Network parity / stop bits | FLOAT32 | ABCD | Read/write | 0 = No parity, 1 stop bit (default); 1 = Even parity, 1 stop bit; 2 = Odd parity, 1 stop bit; 3 = No parity, 2 stop bits | |||
| HR | 20doc 40021 | Network node address | 1-247, default 1. | FLOAT32 | ABCD | Read/write | |||
| HR | 28doc 40029 | Network baud rate | FLOAT32 | ABCD | Read/write | 0 = 2400; 1 = 4800; 2 = 9600 (default); 5 = 1200 | |||
| HR | 86doc 40087 | Pulse 1 energy type | FLOAT32 | ABCD | Read/write | 1 = Import active energy; 2 = Total active energy; 4 = Export active energy (default); 5 = Import reactive energy; 6 = Total reactive energy; 8 = Export reactive energy | |||
| HR | 61456doc 461457 | Clear history data | Write 0x0000 to clear maximum demand. | UINT16 | Write | 0 = Clear maximum demand | |||
| HR | 63760doc 463761 | Pulse 1 divisor | UINT16 | Read/write | 0 = 0.001 kWh(kVArh)/imp (default); 1 = 0.01 kWh(kVArh)/imp; 2 = 0.1 kWh(kVArh)/imp; 3 = 1 kWh(kVArh)/imp | ||||
| HR | 63776doc 463777 | Measurement mode | How total energy is calculated. | UINT16 | Read/write | 1 = Total = import; 2 = Total = import + export (default); 3 = Total = import - export | |||
| HR | 63792doc 463793 | Running time | Continuous working period in hours. | FLOAT32 | ABCD | h | Read/write |
Notes on this map
- Word order: the document states floats are sent most significant register first by default, and its read example returns 43 66 33 34 for 230.2 V. All floats here are ABCD. The 'Register Order' register it mentions has no address in the document.
- Several register names in the source are printed only in Chinese (demand registers 30085-30095, 30259, 30265 and the 461457 reset); they are translated here.
- Source host: the PDF is served from the media store used by Eastron Europe (Fastron Electronics, Eastron's UK distributor) for its product pages.
- Left out: 462721 (demand interval / slide time / scroll / backlight), which is a 4-byte BCD packed field.
- 30387 'Current resettable total reactive energy' is printed with unit kWh; kept as printed, flagged in its description.
- The library's separate SDM230-DI file covers the newer DI variant from a different manual.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Eastron SDM230-Modbus
What Modbus registers does the Eastron SDM230-Modbus have?
This map lists 53 registers: 44 input registers, 9 holding registers. 9 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Eastron SDM230-Modbus Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The tables print 30001/40001-style numbers (six-digit 46xxxx for the F0xx/F9xx block) beside the hex start address sent on the wire, e.g. 30073 = 0x0048 and 463777 = 0xF920. Wire address = printed number minus 30001, 40001 or 400001.
What byte order does the Eastron SDM230-Modbus use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Eastron SDM230-Modbus?
Start with IR 0 Voltage (Voltage); IR 6 Current (Current); IR 12 Active power (Active power); IR 30 Power factor (Power factor); IR 70 Frequency of supply voltages (Frequency); IR 72 Import active energy since last reset (Import kWh); IR 342 Total active energy (Total kWh).
How do I enable Modbus control of the Eastron SDM230-Modbus?
Modbus RTU is always active on the RS485 terminals; no enable step is documented.
Where is the official Eastron SDM230-Modbus Modbus documentation?
The source is Eastron SDM230Modbus Protocol V1.1 (SDM230-2T Smart Meter Modbus Protocol Implementation) (V1.1), published free by Eastron at https://res.cloudinary.com/fastron-electronics/image/upload/v1619064123/Eastron%20Europe/SDM230-MODBUS_Protocol.pdf.
More Eastron Modbus register maps
- Energy meter
Eastron SDM120-Modbus
Eastron SDM120Modbus single-phase DIN-rail meter (direct connected), protocol implementation V2.4.
Also known as: SDM120M, SDM120Modbus, SDM120-M - Energy meter
Eastron SDM120CT-40mA
Eastron SDM120CT-40mA single-phase CT-connected DIN-rail meter with RS485 Modbus RTU, user manual V1.0 (2026-07-16).
Also known as: SDM120CT-M-40mA, SDM120CT-M 40mA - Energy meter
Eastron SDM120CT-M
Eastron SDM120CTM single-phase CT-operated DIN-rail meter (1 A / 5 A CT secondary), protocol implementation V1.3. Not the SDM120CT-40mA.
Also known as: SDM120CTM, SDM120CT Modbus, SDM120CT-MV - Energy meter
Eastron SDM230-DI
Eastron SDM230-DI single-phase 100 A DIN-rail meter with two digital inputs and RS485 Modbus RTU, manual 2025 V1.00.
Also known as: SDM230 DI - Energy meter
Eastron SDM630-DI
Eastron SDM630-DI three-phase DIN-rail meter (100 A direct, two digital inputs, RS485 Modbus RTU), manual V1.02.
Also known as: SDM630 DI - Energy meter
Eastron SDM630-Modbus
Eastron SDM630Modbus three-phase DIN-rail meter, protocol implementation V1.8 as published by Eastron Europe.
Also known as: SDM630Modbus, SDM630 Modbus V2, SDM630-Modbus V2 - Energy meter
Eastron SDM630MCT
Eastron SDM630MCT three-phase CT-connected DIN-rail meter with RS485 Modbus RTU, protocol implementation V1.7.
Also known as: SDM630 MCT
Other power & energy meters register maps
- Sensor (electromagnetic flowmeter)
Endress+Hauser Proline Promag 300 electromagnetic flowmeter (Modbus RS485)
Promag 300 with the Modbus RS485 communication option, parameter description GP01053D/06/EN/04.22.
Also known as: Promag 300, Promag P 300, Promag H 300, Promag W 300 - Energy meter
Fronius Fronius Smart Meter via Datamanager (SunSpec meter model int+SF)
An energy meter wired to a Fronius Datamanager (or Hybridmanager) over Modbus RTU and republished by it, with SunSpec Model Type set to int+SF (meter model 201/202/203).
Also known as: Fronius Smart Meter 63A, Fronius Smart Meter 50kA, Fronius Smart Meter TS, SunSpec meter model 201/202/203 - Power meter
IME Nemo 96HDLe multifunction meter (MF964)
IME Nemo 96HDLe panel meter MF964 with RS-485, per protocol PR130 (software 5.08).
Also known as: MF964, Nemo 96HDLe - Energy meter
inepro Metering PRO2 single-phase energy meter (2026 PRO line)
PRO2-Mod (art. 1201) and PRO2-Mod-Ba (art. 1202, with RTC tariffs) from the 2026 PRO2 user manual version 1.3; the PRO2-S has no Modbus.
Also known as: PRO2-Mod, PRO2-Mod-Ba, PRO2 1U AC 100A Mod T MID, PRO2 1U AC 100A Mod T Ba MID, 1201, 1202 - Power meter (power analyser)
Janitza UMG 509 power analyser (Modbus RTU)
UMG 509 (the original, non-PRO model), per Modbus address list 1.059.004.2.d. For the UMG 509-PRO use its own map.
Also known as: UMG509, UMG 509, Janitza UMG509 - Power meter (power quality analyser)
Janitza UMG 605-PRO power quality analyser (Modbus RTU / Modbus TCP)
UMG 605-PRO from firmware release 5.028, per address list 1.038.009.7.h (09/2022).
Also known as: UMG605-PRO, UMG 605PRO, UMG605PRO, Janitza UMG 605
All power & energy meters Modbus register maps →
Source: Eastron SDM230Modbus Protocol V1.1 (SDM230-2T Smart Meter Modbus Protocol Implementation) · V1.1. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.