- Home
- Modbus register maps
- Grundfos
- Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)
Pump controller (wastewater lift station) · Modbus register map
Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) Modbus register map
Updated 19 November 2026
Grundfos Dedicated Controls runs wastewater lift stations with up to six pumps, a mixer, level sensors or float switches. A CIM module in the CU 36X makes it a Modbus slave with blocks for pit control, pit status, pit data and one 50-register block per pump. This map covers pit commands and level setpoints, operating mode and per-pump state bits, pit level, flows, energy and overflow counters, and the main per-pump data (run hours, starts, current, power, frequency).
This page lists 318 Modbus registers for the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) — 31 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Grundfos’s own free documentation (linked below) and checked against it.
- Manufacturer
- Grundfos
- Model
- Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)
- Equipment type
- Pump controller (wastewater lift station)
- Registers
- 318 (31 writable)
- Transport
- Modbus RTU, Modbus TCP
- Default unit ID
- Not stated
- Default serial
- 19200 baud, 8E1
- TCP port
- 502
- Documented addressing
- 1-based (subtract 1 for the wire address)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- Dedicated Controls, CU 361, CU 362, CIM 200, CIM 260, CIM 500, 98393520
Integration notes: Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)
Poll 00203 (operating mode), 00206/00209 (pumps running / in alarm) and 00301 (pit level) for the station overview, and each pump block for run hours, starts and current. Use PitControl 00101 to reset alarms, interlock the pit or return it to Auto, and 00103-00108 to force pumps on or off.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 202 | OperatingMode | UINT16 | Pit operating mode | Read |
| HR 205 | PitPumpsRunning | BITMAP16 | Pumps running bits | Read |
| HR 208 | PitPumpsAlarm | BITMAP16 | Pumps in alarm bits | Read |
| HR 300 | PitWaterLevel | UINT16 | Pit water level | Read |
| HR 100 | PitControl | BITMAP16 | Reset / interlock / auto commands | Read/write |
| HR 102 | PitPump1Control | UINT16 | Pump 1 manual control | Read/write |
| HR 417 | Pump1Current | UINT16 | Pump 1 motor current | Read |
| HR 403 | Pump1OperatingTime | UINT32 ABCD | Pump 1 operating hours | Read |
Enable Modbus control & writes
Fit the CIM module in the CU 36X; set the address and speed on its switches (CIM 200). Remote control needs write access: if SCADA PIN protection is on, write the PIN to 00109 first and check PitStatus bit 5.
Byte order & addressing
- Control bits act on a rising edge; with AutoAckControlBits = 1 (default) the CIM clears them itself.
- InterlockPit (00101 bit 3) stops all pumps for the time in SetInterlockTimeout (00111, minutes); the pit then returns to Auto by itself.
Network setup
- CIM 200 default: 19200 baud, even parity, 1 stop bit; SW3 selects no parity with 2 stop bits.
- CIM 500: select Modbus TCP on the rotary switch; port 502.
Watch out for
- A changed RegisterOffset (00002) moves every register above 00100.
- Most flow, energy and overflow values need the matching sensor (flow meter, MP 204, level sensor) or read 0xFFFF.
Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 00001 | SlaveMinimumReplyDelay | Extra reply delay 0-10000 ms (default 0). | UINT16 | ms | Read/write | |||
| HR | 1doc 00002 | RegisterOffset | Offset added to addresses above 00100; default 0. | UINT16 | Read/write | ||||
| HR | 4doc 00005 | AutoAckControlBits | UINT16 | Read/write | 0 = Disabled; 1 = Enabled (default) | ||||
| HR | 23doc 00024 | ActualModbusAddress | Slave address in use. | UINT16 | Read | ||||
| HR | 29doc 00030 | UnitFamily | 26 = Dedicated Controls. | UINT16 | Read | ||||
| HR | 30doc 00031 | UnitType | UINT16 | Read | |||||
| HR | 31doc 00032 | UnitVersion | UINT16 | Read | |||||
| HR | 100doc 00101 | PitControl | Command bits, act on a 0 to 1 edge. | BITMAP16 | Read/write | bit 0 = ResetAlarm; bit 2 = ResetEventLog; bit 3 = InterlockPit (stop all pumps for InterlockTimeout); bit 4 = AutoPit (back to Auto mode); bit 5 = CallBackAck; bit 6 = ResetUserDefCounter1; bit 7 = ResetUserDefCounter2; bit 8 = ResetUserDefCounter3; bit 9 = CallBackTest | |||
| HR | 101doc 00102 | CustomRelayControl | BITMAP16 | Read/write | bit 0 = SetCustomRelay; bit 1 = PulseCustomRelay | ||||
| HR | 102doc 00103 | PitPump1Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 103doc 00104 | PitPump2Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 104doc 00105 | PitPump3Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 105doc 00106 | PitPump4Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 106doc 00107 | PitPump5Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 107doc 00108 | PitPump6Control | UINT16 | Read/write | 0 = Auto (controlled by CU 36X); 1 = Forced start; 2 = Forced stop | ||||
| HR | 108doc 00109 | ScadaPinCode | PIN for remote control when SCADA PIN protection is on. | UINT16 | Read/write | ||||
| HR | 110doc 00111 | SetInterlockTimeout | Interlock duration for the InterlockPit command. | UINT16 | min | Read/write | |||
| HR | 111doc 00112 | SetRealTimeClock | UNIX time; write HI then LO. | UINT32 | ABCD | s | Read/write | ||
| HR | 120doc 00121 | SetOverflowLevel | UINT16 | × 0.01 | m | Read/write | |||
| HR | 121doc 00122 | SetHighLevel | UINT16 | × 0.01 | m | Read/write | |||
| HR | 122doc 00123 | SetAlarmLevel | UINT16 | × 0.01 | m | Read/write | |||
| HR | 123doc 00124 | SetDryRunningLevel | UINT16 | × 0.01 | m | Read/write | |||
| HR | 124doc 00125 | SetFoamDrainingLevel | UINT16 | × 0.01 | m | Read/write | |||
| HR | 125doc 00126 | SetStartLevelPump1 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 126doc 00127 | SetStopLevelPump1 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 127doc 00128 | SetStartLevelPump2 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 128doc 00129 | SetStopLevelPump2 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 129doc 00130 | SetStartLevelPump3 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 130doc 00131 | SetStopLevelPump3 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 131doc 00132 | SetStartLevelPump4 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 132doc 00133 | SetStopLevelPump4 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 133doc 00134 | SetStartLevelPump5 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 134doc 00135 | SetStopLevelPump5 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 135doc 00136 | SetStartLevelPump6 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 136doc 00137 | SetStopLevelPump6 | UINT16 | × 0.01 | m | Read/write | |||
| HR | 200doc 00201 | AcknowledgeRegister | Command acknowledgements when AutoAckControlBits = 0. | BITMAP16 | Read | bit 0 = AckResetAlarm; bit 1 = AckSetRtc; bit 2 = AckResetEventLog; bit 3 = AckInterlockPit; bit 4 = AckAutoPit; bit 5 = AckCallBack; bit 6 = ResetUserDefCounter1; bit 7 = ResetUserDefCounter2; bit 8 = ResetUserDefCounter3; bit 9 = CallBackTest; bit 10 = RelayPulse | |||
| HR | 201doc 00202 | PitStatus | BITMAP16 | Read | bit 1 = AlarmActive; bit 2 = WarningActive; bit 3 = ManualControl; bit 4 = ScadaPinCodeEnabled; bit 5 = WriteAccess | ||||
| HR | 202doc 00203 | OperatingMode | UINT16 | Read | 0 = Standby (stopped by level control); 1 = Startup delay; 2 = Pumping; 3 = Stop delay; 4 = Pumping max.; 5 = Stopped; 6 = Foam draining; 7 = Daily emptying; 8 = Pump anti-seizing; 9 = Manual control; 10 = Interlock control; 11 = Mains supply fault; 12 = Level sensor fault; 13 = All enabled pumps in alarm; 14 = All pumps out of operation; 15 = CU 36X in service mode | ||||
| HR | 203doc 00204 | PitPumpsPresence | BITMAP16 | Read | bit 0 = Pump 1 present; bit 1 = Pump 2 present; bit 2 = Pump 3 present; bit 3 = Pump 4 present; bit 4 = Pump 5 present; bit 5 = Pump 6 present; bit 6 = Mixer present | ||||
| HR | 204doc 00205 | PitPumpsDisabled | BITMAP16 | Read | bit 0 = Pump 1 disabled; bit 1 = Pump 2 disabled; bit 2 = Pump 3 disabled; bit 3 = Pump 4 disabled; bit 4 = Pump 5 disabled; bit 5 = Pump 6 disabled; bit 6 = Mixer disabled | ||||
| HR | 205doc 00206 | PitPumpsRunning | BITMAP16 | Read | bit 0 = Pump 1 running; bit 1 = Pump 2 running; bit 2 = Pump 3 running; bit 3 = Pump 4 running; bit 4 = Pump 5 running; bit 5 = Pump 6 running; bit 6 = Mixer running | ||||
| HR | 206doc 00207 | PitPumpsMonitoringFault | BITMAP16 | Read | bit 0 = Pump 1 monitoring fault; bit 1 = Pump 2 monitoring fault; bit 2 = Pump 3 monitoring fault; bit 3 = Pump 4 monitoring fault; bit 4 = Pump 5 monitoring fault; bit 5 = Pump 6 monitoring fault; bit 6 = Mixer monitoring fault | ||||
| HR | 207doc 00208 | PitPumpsWarning | BITMAP16 | Read | bit 0 = Pump 1 warning; bit 1 = Pump 2 warning; bit 2 = Pump 3 warning; bit 3 = Pump 4 warning; bit 4 = Pump 5 warning; bit 5 = Pump 6 warning; bit 6 = Mixer warning | ||||
| HR | 208doc 00209 | PitPumpsAlarm | BITMAP16 | Read | bit 0 = Pump 1 alarm; bit 1 = Pump 2 alarm; bit 2 = Pump 3 alarm; bit 3 = Pump 4 alarm; bit 4 = Pump 5 alarm; bit 5 = Pump 6 alarm; bit 6 = Mixer alarm | ||||
| HR | 209doc 00210 | PitAlarms1 | Pit alarm events, word 1 (see the manual's alarm list). | BITMAP16 | Read | ||||
| HR | 210doc 00211 | PitAlarms2 | Pit alarm events, word 2 (see the manual's alarm list). | BITMAP16 | Read | ||||
| HR | 211doc 00212 | PitAlarms3 | Pit alarm events, word 3 (see the manual's alarm list). | BITMAP16 | Read | ||||
| HR | 212doc 00213 | PitWarnings1 | Pit warning events, word 1. | BITMAP16 | Read | ||||
| HR | 213doc 00214 | PitWarnings2 | Pit warning events, word 2. | BITMAP16 | Read | ||||
| HR | 214doc 00215 | PitWarnings3 | Pit warning events, word 3. | BITMAP16 | Read | ||||
| HR | 215doc 00216 | EventLogLatestID | ID of the newest event log entry. | UINT16 | Read | ||||
| HR | 216doc 00217 | NumberOfFloatSwitches | Installed float switches (0-5). | UINT16 | Read | ||||
| HR | 217doc 00218 | FloatSwitchesStatus | BITMAP16 | Read | bit 0 = Float switch 1 on; bit 1 = Float switch 2 on; bit 2 = Float switch 3 on; bit 3 = Float switch 4 on; bit 4 = Float switch 5 on; bit 5 = Extra overflow switch on | ||||
| HR | 218doc 00219 | FloatSwitch1Function | UINT16 | Read | 0 = Not used; 1 = Dry running; 3 = Stop of all pumps; 4 = Stop; 5 = Stop of first pump; 6 = Stop of second pump; 11 = Start/stop; 12 = Start of first pump/stop; 13 = Start; 14 = Start of first pump; 15 = Start of second pump; 20 = Start of all pumps; 21 = Alarm level; 23 = High level | ||||
| HR | 219doc 00220 | FloatSwitch2Function | UINT16 | Read | 0 = Not used; 1 = Dry running; 3 = Stop of all pumps; 4 = Stop; 5 = Stop of first pump; 6 = Stop of second pump; 11 = Start/stop; 12 = Start of first pump/stop; 13 = Start; 14 = Start of first pump; 15 = Start of second pump; 20 = Start of all pumps; 21 = Alarm level; 23 = High level | ||||
| HR | 220doc 00221 | FloatSwitch3Function | UINT16 | Read | 0 = Not used; 1 = Dry running; 3 = Stop of all pumps; 4 = Stop; 5 = Stop of first pump; 6 = Stop of second pump; 11 = Start/stop; 12 = Start of first pump/stop; 13 = Start; 14 = Start of first pump; 15 = Start of second pump; 20 = Start of all pumps; 21 = Alarm level; 23 = High level | ||||
| HR | 221doc 00222 | FloatSwitch4Function | UINT16 | Read | 0 = Not used; 1 = Dry running; 3 = Stop of all pumps; 4 = Stop; 5 = Stop of first pump; 6 = Stop of second pump; 11 = Start/stop; 12 = Start of first pump/stop; 13 = Start; 14 = Start of first pump; 15 = Start of second pump; 20 = Start of all pumps; 21 = Alarm level; 23 = High level | ||||
| HR | 240doc 00241 | HighLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 241doc 00242 | AlarmLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 242doc 00243 | DryRunningLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 243doc 00244 | FoamDrainingLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 244doc 00245 | StartLevelPump1 | UINT16 | × 0.01 | m | Read | |||
| HR | 245doc 00246 | StopLevelPump1 | UINT16 | × 0.01 | m | Read | |||
| HR | 246doc 00247 | StartLevelPump2 | UINT16 | × 0.01 | m | Read | |||
| HR | 247doc 00248 | StopLevelPump2 | UINT16 | × 0.01 | m | Read | |||
| HR | 248doc 00249 | StartLevelPump3 | UINT16 | × 0.01 | m | Read | |||
| HR | 249doc 00250 | StopLevelPump3 | UINT16 | × 0.01 | m | Read | |||
| HR | 250doc 00251 | StartLevelPump4 | UINT16 | × 0.01 | m | Read | |||
| HR | 251doc 00252 | StopLevelPump4 | UINT16 | × 0.01 | m | Read | |||
| HR | 252doc 00253 | StartLevelPump5 | UINT16 | × 0.01 | m | Read | |||
| HR | 253doc 00254 | StopLevelPump5 | UINT16 | × 0.01 | m | Read | |||
| HR | 254doc 00255 | StartLevelPump6 | UINT16 | × 0.01 | m | Read | |||
| HR | 255doc 00256 | StopLevelPump6 | UINT16 | × 0.01 | m | Read | |||
| HR | 257doc 00258 | BatteryVoltage | UINT16 | × 0.1 | V | Read | |||
| HR | 300doc 00301 | PitWaterLevel | Needs a level sensor. | UINT16 | × 0.01 | m | Read | ||
| HR | 301doc 00302 | PitSwitchWaterLevel | Level from float switches, 0-5. | UINT16 | Read | ||||
| HR | 302doc 00303 | PitDepth | UINT16 | × 0.01 | m | Read | |||
| HR | 303doc 00304 | PitFlowIn | UINT16 | × 0.1 | l/s | Read | |||
| HR | 304doc 00305 | PitAverageFlowIn | UINT16 | × 0.1 | l/s | Read | |||
| HR | 305doc 00306 | PitFlowOut | UINT16 | × 0.1 | l/s | Read | |||
| HR | 306doc 00307 | PitAverageFlowOut | UINT16 | × 0.1 | l/s | Read | |||
| HR | 307doc 00308 | PitPower | UINT32 | ABCD | W | Read | |||
| HR | 309doc 00310 | PitEnergy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 311doc 00312 | PitEnergyYesterday | UINT16 | × 0.1 | kWh | Read | |||
| HR | 312doc 00313 | PitEnergyToday | UINT16 | × 0.1 | kWh | Read | |||
| HR | 313doc 00314 | PitSpecificEnergy | UINT16 | Wh/m³ | Read | ||||
| HR | 314doc 00315 | PitPumpedVolume | UINT32 | ABCD | × 0.1 | m³ | Read | ||
| HR | 316doc 00317 | PitPumpedVolumeYesterday | UINT16 | × 0.1 | m³ | Read | |||
| HR | 317doc 00318 | PitPumpedVolumeToday | UINT16 | × 0.1 | m³ | Read | |||
| HR | 318doc 00319 | PitMixerStartsPerHour | UINT16 | Read | |||||
| HR | 319doc 00320 | PitOverflowVolume | UINT16 | × 0.1 | m³ | Read | |||
| HR | 320doc 00321 | PitOverflowVolumeYesterday | UINT16 | × 0.1 | m³ | Read | |||
| HR | 321doc 00322 | PitOverflowVolumeToday | UINT16 | × 0.1 | m³ | Read | |||
| HR | 322doc 00323 | PitOverflowTime | UINT16 | min | Read | ||||
| HR | 323doc 00324 | PitOverflowTimeYesterday | UINT16 | min | Read | ||||
| HR | 324doc 00325 | PitOverflowTimeToday | UINT16 | min | Read | ||||
| HR | 325doc 00326 | PitOverflowCounter | UINT16 | Read | |||||
| HR | 326doc 00327 | PitOverflowCounterYesterday | UINT16 | Read | |||||
| HR | 327doc 00328 | PitOverflowCounterToday | UINT16 | Read | |||||
| HR | 328doc 00329 | PitOperatingTime | Total power-on time. | UINT32 | ABCD | min | Read | ||
| HR | 330doc 00331 | Pit2PumpsOprTime | Total time with 2 pumps running together. | UINT32 | ABCD | min | Read | ||
| HR | 332doc 00333 | Pit2PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 333doc 00334 | Pit2PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 334doc 00335 | Pit3PumpsOprTime | Total time with 3 pumps running together. | UINT32 | ABCD | min | Read | ||
| HR | 336doc 00337 | Pit3PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 337doc 00338 | Pit3PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 338doc 00339 | Pit4PumpsOprTime | Total time with 4 pumps running together. | UINT32 | ABCD | min | Read | ||
| HR | 340doc 00341 | Pit4PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 341doc 00342 | Pit4PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 342doc 00343 | Pit5PumpsOprTime | Total time with 5 pumps running together. | UINT32 | ABCD | min | Read | ||
| HR | 344doc 00345 | Pit5PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 345doc 00346 | Pit5PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 346doc 00347 | Pit6PumpsOprTime | Total time with 6 pumps running together. | UINT32 | ABCD | min | Read | ||
| HR | 348doc 00349 | Pit6PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 349doc 00350 | Pit6PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 350doc 00351 | UserAnalogInput1 | UINT16 | × 0.1 | % | Read | |||
| HR | 351doc 00352 | UserAnalogInput2 | UINT16 | × 0.1 | % | Read | |||
| HR | 352doc 00353 | UserAnalogInput3 | UINT16 | × 0.1 | % | Read | |||
| HR | 353doc 00354 | Pit0PumpsOprTime | Total time with no pump running. | UINT32 | ABCD | min | Read | ||
| HR | 355doc 00356 | Pit0PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 356doc 00357 | Pit0PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 357doc 00358 | Pit1PumpsOprTime | Total time with one pump running. | UINT32 | ABCD | min | Read | ||
| HR | 359doc 00360 | Pit1PumpsOprTimeYesterday | UINT16 | min | Read | ||||
| HR | 360doc 00361 | Pit1PumpsOprTimeToday | UINT16 | min | Read | ||||
| HR | 361doc 00362 | MixerRuntime | UINT16 | min | Read | ||||
| HR | 362doc 00363 | MixerStartCounter | UINT16 | Read | |||||
| HR | 366doc 00367 | PitOutletPressure | UINT16 | × 0.001 | bar | Read | |||
| HR | 367doc 00368 | PitOverflowVolume32bit | UINT32 | ABCD | × 0.1 | m³ | Read | ||
| HR | 369doc 00370 | PitOverflowTime32bit | UINT32 | ABCD | min | Read | |||
| HR | 377doc 00378 | H2SLevelActual | UINT16 | ppm | Read | ||||
| HR | 378doc 00379 | H2SLevelToday | Average today. | UINT16 | ppm | Read | |||
| HR | 379doc 00380 | H2SLevelYesterday | Average yesterday. | UINT16 | ppm | Read | |||
| HR | 380doc 00381 | DosingFeedTankLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 381doc 00382 | DosingVolumeTotal | UINT32 | ABCD | × 0.001 | m³ | Read | ||
| HR | 383doc 00384 | DosingVolumeToday | UINT16 | × 0.001 | m³ | Read | |||
| HR | 384doc 00385 | DosingVolumeYesterday | UINT16 | × 0.001 | m³ | Read | |||
| HR | 385doc 00386 | DosingRefActual | UINT16 | × 0.1 | l/h | Read | |||
| HR | 386doc 00387 | GrinderOperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 400doc 00401 | Pump1Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 401doc 00402 | Pump1ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 403doc 00404 | Pump1OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 405doc 00406 | Pump1TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 407doc 00408 | Pump1OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 408doc 00409 | Pump1OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 409doc 00410 | Pump1LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 410doc 00411 | Pump1StartCounter | UINT32 | ABCD | Read | ||||
| HR | 412doc 00413 | Pump1StartCounterYesterday | UINT16 | Read | |||||
| HR | 413doc 00414 | Pump1StartCounterToday | UINT16 | Read | |||||
| HR | 414doc 00415 | Pump1StartsPerHour | UINT16 | Read | |||||
| HR | 415doc 00416 | Pump1Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 416doc 00417 | Pump1LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 417doc 00418 | Pump1Current | UINT16 | × 0.1 | A | Read | |||
| HR | 418doc 00419 | Pump1LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 419doc 00420 | Pump1Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 420doc 00421 | Pump1Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 421doc 00422 | Pump1WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 428doc 00429 | Pump1MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 429doc 00430 | Pump1MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 430doc 00431 | Pump1Power | UINT32 | ABCD | W | Read | |||
| HR | 432doc 00433 | Pump1Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 434doc 00435 | Pump1CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 435doc 00436 | Pump1Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 436doc 00437 | Pump1VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 437doc 00438 | Pump1Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 438doc 00439 | Pump1iAsym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 446doc 00447 | Pump1ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 447doc 00448 | Pump1ActualSetpoint | UINT16 | % | Read | ||||
| HR | 448doc 00449 | Pump1FixedFrequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 450doc 00451 | Pump2Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 451doc 00452 | Pump2ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 453doc 00454 | Pump2OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 455doc 00456 | Pump2TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 457doc 00458 | Pump2OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 458doc 00459 | Pump2OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 459doc 00460 | Pump2LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 460doc 00461 | Pump2StartCounter | UINT32 | ABCD | Read | ||||
| HR | 462doc 00463 | Pump2StartCounterYesterday | UINT16 | Read | |||||
| HR | 463doc 00464 | Pump2StartCounterToday | UINT16 | Read | |||||
| HR | 464doc 00465 | Pump2StartsPerHour | UINT16 | Read | |||||
| HR | 465doc 00466 | Pump2Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 466doc 00467 | Pump2LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 467doc 00468 | Pump2Current | UINT16 | × 0.1 | A | Read | |||
| HR | 468doc 00469 | Pump2LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 469doc 00470 | Pump2Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 470doc 00471 | Pump2Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 471doc 00472 | Pump2WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 478doc 00479 | Pump2MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 479doc 00480 | Pump2MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 480doc 00481 | Pump2Power | UINT32 | ABCD | W | Read | |||
| HR | 482doc 00483 | Pump2Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 484doc 00485 | Pump2CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 485doc 00486 | Pump2Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 486doc 00487 | Pump2VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 487doc 00488 | Pump2Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 488doc 00489 | Pump2Asym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 496doc 00497 | Pump2ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 497doc 00498 | Pump2ActualSetpoint | UINT16 | % | Read | ||||
| HR | 498doc 00499 | Pump2FixedFrequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 500doc 00501 | Pump3Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 501doc 00502 | Pump3ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 503doc 00504 | Pump3OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 505doc 00506 | Pump3TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 507doc 00508 | Pump3OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 508doc 00509 | Pump3OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 509doc 00510 | Pump3LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 510doc 00511 | Pump3StartCounter | UINT32 | ABCD | Read | ||||
| HR | 512doc 00513 | Pump3StartCounterYesterday | UINT16 | Read | |||||
| HR | 513doc 00514 | Pump3StartCounterToday | UINT16 | Read | |||||
| HR | 514doc 00515 | Pump3StartsPerHour | UINT16 | Read | |||||
| HR | 515doc 00516 | Pump3Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 516doc 00517 | Pump3LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 517doc 00518 | Pump3Current | UINT16 | × 0.1 | A | Read | |||
| HR | 518doc 00519 | Pump3LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 519doc 00520 | Pump3Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 520doc 00521 | Pump3Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 521doc 00522 | Pump3WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 528doc 00529 | Pump3MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 529doc 00530 | Pump3MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 530doc 00531 | Pump3Power | UINT32 | ABCD | W | Read | |||
| HR | 532doc 00533 | Pump3Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 534doc 00535 | Pump3CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 535doc 00536 | Pump3Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 536doc 00537 | Pump3VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 537doc 00538 | Pump3Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 538doc 00539 | Pump3Asym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 546doc 00547 | Pump3ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 547doc 00548 | Pump3ActualSetpoint | UINT16 | % | Read | ||||
| HR | 548doc 00549 | Pump3FixedFrequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 550doc 00551 | Pump4Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 551doc 00552 | Pump4ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 553doc 00554 | Pump4OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 555doc 00556 | Pump4TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 557doc 00558 | Pump4OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 558doc 00559 | Pump4OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 559doc 00560 | Pump4LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 560doc 00561 | Pump4StartCounter | UINT32 | ABCD | Read | ||||
| HR | 562doc 00563 | Pump4StartCounterYesterday | UINT16 | Read | |||||
| HR | 563doc 00564 | Pump4StartCounterToday | UINT16 | Read | |||||
| HR | 564doc 00565 | Pump4StartsPerHour | UINT16 | Read | |||||
| HR | 565doc 00566 | Pump4Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 566doc 00567 | Pump4LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 567doc 00568 | Pump4Current | UINT16 | × 0.1 | A | Read | |||
| HR | 568doc 00569 | Pump4LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 569doc 00570 | Pump4Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 570doc 00571 | Pump4Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 571doc 00572 | Pump4WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 578doc 00579 | Pump4MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 579doc 00580 | Pump4MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 580doc 00581 | Pump4Power | UINT32 | ABCD | W | Read | |||
| HR | 582doc 00583 | Pump4Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 584doc 00585 | Pump4CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 585doc 00586 | Pump4Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 586doc 00587 | Pump4VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 587doc 00588 | Pump4Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 588doc 00589 | Pump4Asym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 596doc 00597 | Pump4ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 597doc 00598 | Pump4ActualSetpoint | UINT16 | % | Read | ||||
| HR | 598doc 00599 | Pump4FixedFrequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 600doc 00601 | Pump5Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 601doc 00602 | Pump5ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 603doc 00604 | Pump5OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 605doc 00606 | Pump5TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 607doc 00608 | Pump5OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 608doc 00609 | Pump5OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 609doc 00610 | Pump5LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 610doc 00611 | Pump5StartCounter | UINT32 | ABCD | Read | ||||
| HR | 612doc 00613 | Pump5StartCounterYesterday | UINT16 | Read | |||||
| HR | 613doc 00614 | Pump5StartCounterToday | UINT16 | Read | |||||
| HR | 614doc 00615 | Pump5StartsPerHour | UINT16 | Read | |||||
| HR | 615doc 00616 | Pump5Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 616doc 00617 | Pump5LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 617doc 00618 | Pump5Current | UINT16 | × 0.1 | A | Read | |||
| HR | 618doc 00619 | Pump5LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 619doc 00620 | Pump5Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 620doc 00621 | Pump5Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 621doc 00622 | Pump5WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 628doc 00629 | Pump5MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 629doc 00630 | Pump5MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 630doc 00631 | Pump5Power | UINT32 | ABCD | W | Read | |||
| HR | 632doc 00633 | Pump5Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 634doc 00635 | Pump5CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 635doc 00636 | Pump5Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 636doc 00637 | Pump5VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 637doc 00638 | Pump5Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 638doc 00639 | Pump5Asym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 646doc 00647 | Pump5ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 647doc 00648 | Pump5ActualSetpoint | UINT16 | % | Read | ||||
| HR | 648doc 00649 | Pump5FixedFrequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 650doc 00651 | Pump6Status | BITMAP16 | Read | bit 0 = Present; bit 1 = Running; bit 2 = Monitoring fault; bit 3 = Warning; bit 4 = Alarm; bit 5 = IO 111 present; bit 6 = IO 111 fault; bit 7 = MP 204 present; bit 8 = MP 204 fault; bit 9 = CUE present; bit 10 = CUE fault; bit 11 = Pump disabled | ||||
| HR | 651doc 00652 | Pump6ControlSource | UINT16 | Read | 0 = Auto; 1 = Switch; 2 = Display; 3 = Remote (bus) | ||||
| HR | 653doc 00654 | Pump6OperatingTime | UINT32 | ABCD | min | Read | |||
| HR | 655doc 00656 | Pump6TimeToService | UINT32 | ABCD | min | Read | |||
| HR | 657doc 00658 | Pump6OperatingTimeYesterday | UINT16 | min | Read | ||||
| HR | 658doc 00659 | Pump6OperatingTimeToday | UINT16 | min | Read | ||||
| HR | 659doc 00660 | Pump6LatestOperatingTime | Length of the last run. | UINT16 | s | Read | |||
| HR | 660doc 00661 | Pump6StartCounter | UINT32 | ABCD | Read | ||||
| HR | 662doc 00663 | Pump6StartCounterYesterday | UINT16 | Read | |||||
| HR | 663doc 00664 | Pump6StartCounterToday | UINT16 | Read | |||||
| HR | 664doc 00665 | Pump6StartsPerHour | UINT16 | Read | |||||
| HR | 665doc 00666 | Pump6Flow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 666doc 00667 | Pump6LatestFlow | UINT16 | × 0.1 | l/s | Read | |||
| HR | 667doc 00668 | Pump6Current | UINT16 | × 0.1 | A | Read | |||
| HR | 668doc 00669 | Pump6LatestCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 669doc 00670 | Pump6Voltage | UINT16 | × 0.1 | V | Read | |||
| HR | 670doc 00671 | Pump6Insulation | UINT16 | × 10 | kΩ | Read | |||
| HR | 671doc 00672 | Pump6WaterInOil | UINT16 | × 0.1 | % | Read | |||
| HR | 678doc 00679 | Pump6MotorTemperature1 | UINT16 | °C | Read | ||||
| HR | 679doc 00680 | Pump6MotorTemperature2 | UINT16 | °C | Read | ||||
| HR | 680doc 00681 | Pump6Power | UINT32 | ABCD | W | Read | |||
| HR | 682doc 00683 | Pump6Energy | UINT32 | ABCD | × 0.1 | kWh | Read | ||
| HR | 684doc 00685 | Pump6CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 685doc 00686 | Pump6Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 686doc 00687 | Pump6VFDmode | UINT16 | Read | 0 = VFD not controlled; 2 = Stopped; 3 = Reverse start; 4 = Start flushing; 5 = Normal; 6 = Run flushing; 7 = Stop flushing; 8 = Specific-energy test | ||||
| HR | 687doc 00688 | Pump6Torque | UINT16 | × 0.1 | Nm | Read | |||
| HR | 688doc 00689 | Pump6Asym | Line current asymmetry. | UINT16 | × 0.1 | % | Read | ||
| HR | 696doc 00697 | Pump6ControlMode | UINT16 | Read | 0 = Fixed frequency; 1 = Linear control; 2 = Minimum control; 3 = PID control | ||||
| HR | 697doc 00698 | Pump6ActualSetpoint | UINT16 | % | Read | ||||
| HR | 698doc 00699 | Pump6FixedFrequency | UINT16 | × 0.01 | Hz | Read |
Notes on this map
- The manual states that 32-bit values are split into registers ending HI and LO and recombined as HI x 65536 + LO, so they are ABCD.
- All registers can be read with function 03 or 04; they are listed as holding registers. 0xFFFF means not available (missing sensor or option).
- Pumps 2-6 repeat the pump 1 layout at +50 registers each (00451, 00501, 00551, 00601, 00651); this was checked against the printed pump 2-6 tables.
- Left out: per-pump alarm/warning words (004x23-004x28, 004x41-004x42), sensor presence and setpoint-select fields, the pit sensor-presence and float-switch 5 registers (00223-00240), most user-defined counters, the real-time clock split registers, the hour log, event log and data log blocks, and the name string. Bit meanings of PitAlarms/PitWarnings are in section 11.11 of the manual and are not decoded here.
- Level and set-level registers are in 0.01 m; writing the Set...Level registers (00121-00137) changes the controller's configured levels.
- Left out: GrinderReverseCounter (00389-00390), because the pit status table also prints 00389 for PitWarnings5, so the number is not unambiguous in this edition.
- Pumps 2-6 print the current asymmetry register as PumpNAsym, while pump 1 uses Pump1iAsym; the names are kept as printed.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)
What Modbus registers does the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) have?
This map lists 318 registers: 318 holding registers. 31 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed as 5-digit register numbers; this manual states that register X is addressed as X - 1 in the telegram (e.g. 00301 PitWaterLevel is wire address 300). Pump n's block starts at 00401 + 50 x (n-1).
What byte order does the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)?
Start with HR 202 OperatingMode (Pit operating mode); HR 205 PitPumpsRunning (Pumps running bits); HR 208 PitPumpsAlarm (Pumps in alarm bits); HR 300 PitWaterLevel (Pit water level); HR 100 PitControl (Reset / interlock / auto commands); HR 102 PitPump1Control (Pump 1 manual control); HR 417 Pump1Current (Pump 1 motor current); HR 403 Pump1OperatingTime (Pump 1 operating hours).
How do I enable Modbus control of the Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)?
Fit the CIM module in the CU 36X; set the address and speed on its switches (CIM 200). Remote control needs write access: if SCADA PIN protection is on, write the PIN to 00109 first and check PitStatus bit 5.
Where is the official Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus) Modbus documentation?
The source is Modbus for Dedicated Controls - CIM 200 Modbus RTU, CIM 260 3G/4G Cellular, CIM 500 Ethernet for Modbus TCP - Functional profile and user manual (98393520), revision 2023-03, published free by Grundfos at https://api.grundfos.com/literature/Grundfosliterature-6012936.pdf.
More Grundfos Modbus register maps
- Pump (booster system / multi-pump controller)
Grundfos Booster systems (Hydro MPC, Hydro Multi-E, Multi-B) via CIM 200 / CIM 500
Grundfos booster systems: Hydro MPC / Control MPC (CU 352), GENIECON MPC, Hydro Multi-B (CU 323), DDD (CU 354), Hydro Multi-E, TPED and MAGNA3-D twin pumps, with CIM/CIU 200, CIM/CIU 500 or SoftCIM.
Also known as: Hydro MPC, Control MPC, CU 352, GENIECON MPC, Hydro Multi-E, Hydro Multi-B, CU 323, DDD, CU 354, TPED, MAGNA3-D, CIM 200, CIM 500, SoftCIM Modbus TCP - Pump (circulator / E-pump / pump drive)
Grundfos E-pumps (MAGNA3, TPE, CRE, CUE) via CIM 200 / CIM 500
Grundfos E-pumps (CRE/CRNE/CRIE, MTRE, CHIE, CME, TPE, TPE Series 2000, NBE/NKE), CUE drives and MAGNA3 with a CIM/CIU 200, CIM/CIU 500 or built-in SoftCIM.
Also known as: MAGNA3, TPE, TPE Series 2000, CRE, CRNE, CRIE, MTRE, CHIE, CME, NBE, NKE, CUE, MGE, CIM 200, CIU 200, CIM 500, CIU 500, SoftCIM Modbus RTU - Pump protection / monitoring module (Sensor)
Grundfos IO 113 pump protection module (Modbus RTU)
Grundfos IO 113 interface module for wastewater and sewage pumps (with or without the SM 113 sensor board) set to Modbus with DIP switch 9; document edition 1.7, January 2015.
Also known as: IO113, IO 113 with SM 113, 98288208 - Pump motor protection relay
Grundfos MP 204 motor protector with CIU 200 / CIU 500 (Modbus)
Grundfos MP 204 electronic motor protector connected over GENIbus to a CIU 200 (Modbus RTU), CIU 250 (GSM/GPRS) or CIU 500 (Modbus TCP) box; functional profile 98393513 (2014-11).
Also known as: MP 204, CIU 200 Modbus RTU, CIU 250 GSM/GPRS, CIU 500 Modbus TCP, 98393513 - Pump (submersible grinder pump pit)
Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)
Up to four Grundfos SEG AUTOADAPT grinder pumps in one or more pits, connected to a CIU 202 (Modbus RTU), CIU 262 (cellular) or CIU 502 (Modbus TCP); functional profile 96846341 (2019-01).
Also known as: SEG AUTOADAPT, CIU 202, CIU 262, CIU 502, 96846341 - Pump (chemical dosing pump)
Grundfos SMART Digital DDA dosing pump (SoftCIM, CIM 200 / CIM 500)
Grundfos SMART Digital DDA dosing pumps: DDA model C with built-in SoftCIM Modbus RTU/TCP, and DDA XL (or others) through a CIM 200 Modbus RTU or CIM 500 Modbus TCP module in a CIU 900, per functional profile 98473491 (09.2026).
Also known as: DDA, DDA S, DDA XL, DDA-C, DDA model C, SMART Digital S, SMART Digital XL, CIM 200, CIM 500, 98473491
Other pumps register maps
- Pump (electric fire pump controller)
Lovato Electric FFL700EP / FFL800EP electric fire pump controllers
FFL700EP and FFL800EP electric fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800EP), per protocol document I589 GB I 08 22.
Also known as: FFL700EP, FFL800EP, FFL 700 EP, FFL 800 EP - Heat pump (air-to-water) Modbus interface
Panasonic CZ-NSMB A2W Modbus PCB for Aquarea air-to-water heat pumps
Panasonic CZ-NSMB Modbus PCB fitted inside Panasonic Air-To-Water control boxes; the manual's compatibility list names the A2W M-Series control module WH-CME8 and the Big A2W 20-30 kW outdoor units WH-WXG20/25/30ME8 with control module WH-CME8L (user manual M02412F0). Some registers carry H/J/K/L-series conditions.
Also known as: CZ-NSMB, A2W Modbus PCB, WH-CME8, WH-CME8L, WH-WXG20ME8, WH-WXG25ME8, WH-WXG30ME8, Aquarea M series Modbus, Big A2W Modbus - Pump (multistage pressure-boosting pump)
Wilo Helix2.0-VE / Medana CH3-LE with CIF module Modbus RTU
Wilo Helix2.0-VE pumps fitted with the plug-in CIF module Modbus RTU (module firmware 1.00-99.99); registers needing a newer module are marked.
Also known as: Wilo-Helix2.0-VE, Medana CH3-LE, Wilo-Medana CH3-LE - Pump controller (switchgear)
Wilo Wilo-Control EC-WP switchgear (ModBus RTU)
Wilo-Control EC-WP for one or two fixed-speed pumps, hardware HW2, software SW102x (instructions Ed.01/2024-08, 2552567).
Also known as: Control EC-WP, Wilo Control EC WP, EC-WP - Heat pump
Daikin DCOM-LT/MB Modbus interface for Daikin Altherma LT heat pumps
Daikin Altherma low-temperature (LT) air-to-water heat pumps fitted with the DCOM-LT/MB (model number 534-001) P1P2-to-Modbus RTU interface, standard operating mode, per reference manual 534-252-A3.
Also known as: DCOM-LT-MB, 534-001, Altherma LT Modbus interface - Heat pump (air-to-water)
Gree Versati heat pump water heater (wired-controller Modbus RTU, protocol V1.5)
Gree Versati air-to-water heat pumps through the BMS port of the wired controller, per 'Modbus Protocol (V1.5) for the Versati Heat Pump Water Heater'. The document itself does not name a generation or refrigerant; the distributor files it as the R32 Versati III protocol.
Also known as: Versati III, R32 Versati, Versati heat pump water heater, Gree Versati Modbus V1.5
All pumps Modbus register maps →
Source: Modbus for Dedicated Controls - CIM 200 Modbus RTU, CIM 260 3G/4G Cellular, CIM 500 Ethernet for Modbus TCP - Functional profile and user manual · 98393520 · rev. 2023-03. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.