- Home
- Modbus register maps
- Grundfos
- SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)
Pump (submersible grinder pump pit) · Modbus register map
Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) Modbus register map
Updated 19 November 2026
SEG AUTOADAPT grinder pumps carry their own level sensing and control; a CIU box links up to four of them to a Modbus master. The map covers the pit commands and start/stop levels for single-pit and multi-pit operation, pit state and alarm bits, pit energy and run-time counters, and a 50-register block per pump with temperatures, voltage, current, power, energy, starts, level and alarm/warning bits.
This page lists 169 Modbus registers for the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) — 28 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Grundfos’s own free documentation (linked below) and checked against it.
- Manufacturer
- Grundfos
- Model
- SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)
- Equipment type
- Pump (submersible grinder pump pit)
- Registers
- 169 (28 writable)
- Transport
- Modbus RTU, Modbus TCP
- Default unit ID
- Not stated
- Default serial
- 19200 baud, 8E1
- TCP port
- 502
- Documented addressing
- 1-based (subtract 1 for the wire address)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- SEG AUTOADAPT, CIU 202, CIU 262, CIU 502, 96846341
Integration notes: Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)
Read 00230-00235 for pump presence, running, alarm and the pit main status, 00301 for the pit level, and each pump block for current, power and alarm bits. Force pumps with 00122-00125 or use the PumpDown bits of PitControl 00101.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 230 | PitPumpsRunning | BITMAP16 | Pumps running bits | Read |
| HR 231 | PitPumpsAlarm | BITMAP16 | Pumps in alarm bits | Read |
| HR 234 | MainStatus | BITMAP16 | Warning / alarm / manual summary | Read |
| HR 300 | WaterLevel | UINT16 | Pit water level | Read |
| HR 100 | PitControl | BITMAP16 | Reset and pump-down commands | Read/write |
| HR 403 | Pump1.AverageLineCurrent | UINT16 | Pump 1 current | Read |
| HR 427 | Pump1.Alarms | BITMAP16 | Pump 1 alarm bits | Read |
Enable Modbus control & writes
Set the CIU 202 address with the hex rotary switches and the speed and parity with the DIP switches; no setting is needed in the pumps. Write the pit levels only in the mode selected by PitMode (00203).
Byte order & addressing
- Control bits are rising-edge commands; with AutoAckControlBits = 1 (default) the CIU clears them.
- Single-pit and multi-pit level registers are separate; the unused set is ignored.
Network setup
- CIU 202 default 19200 baud, even parity, 1 stop bit.
- CIU 502: Modbus TCP on port 502.
Watch out for
- A changed RegisterOffset (00002) shifts all addresses above 00100.
Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 00001 | SlaveMinimumReplyDelay | Extra reply delay 0-10000 ms (default 0). | UINT16 | ms | Read/write | |||
| HR | 1doc 00002 | RegisterOffset | Offset added to addresses above 00100; default 0. | UINT16 | Read/write | ||||
| HR | 4doc 00005 | AutoAckControlBits | UINT16 | Read/write | 0 = Disabled; 1 = Enabled (default) | ||||
| HR | 23doc 00024 | ActualModbusAddress | UINT16 | Read | |||||
| HR | 29doc 00030 | UnitFamily | UINT16 | Read | |||||
| HR | 30doc 00031 | UnitType | UINT16 | Read | |||||
| HR | 31doc 00032 | UnitVersion | UINT16 | Read | |||||
| HR | 100doc 00101 | PitControl | Command bits, act on a 0 to 1 edge. | BITMAP16 | Read/write | bit 0 = ResetAlarm; bit 1 = ResetHistory; bit 2 = PitPump1ResetHistory; bit 3 = PitPump2ResetHistory; bit 4 = PitPump3ResetHistory; bit 5 = PitPump4ResetHistory; bit 6 = PitPump1ResetAlarm; bit 7 = PitPump2ResetAlarm; bit 8 = PitPump3ResetAlarm; bit 9 = PitPump4ResetAlarm; bit 10 = PitPump1PumpDown (pump down once, then level control stops it); bit 11 = PitPump2PumpDown (pump down once, then level control stops it); bit 12 = PitPump3PumpDown (pump down once, then level control stops it); bit 13 = PitPump4PumpDown (pump down once, then level control stops it) | |||
| HR | 101doc 00102 | SetSinglePitStopLevel | Single-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 102doc 00103 | SetSinglePitStartLevelMax | Single-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 103doc 00104 | SetSinglePitStartLevelBand | Single-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 104doc 00105 | SetSinglePitHighWaterLevel | Single-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 105doc 00106 | SetMultiPitPump1StopLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 106doc 00107 | SetMultiPitPump1StartLevelMax | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 107doc 00108 | SetMultiPitPump1StartLevelBand | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 108doc 00109 | SetMultiPitPump1HighWaterLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 109doc 00110 | SetMultiPitPump2StopLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 110doc 00111 | SetMultiPitPump2StartLevelMax | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 111doc 00112 | SetMultiPitPump2StartLevelBand | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 112doc 00113 | SetMultiPitPump2HighWaterLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 113doc 00114 | SetMultiPitPump3StopLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 114doc 00115 | SetMultiPitPump3StartLevelMax | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 115doc 00116 | SetMultiPitPump3StartLevelBand | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 116doc 00117 | SetMultiPitPump3HighWaterLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 117doc 00118 | SetMultiPitPump4StopLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 118doc 00119 | SetMultiPitPump4StartLevelMax | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 119doc 00120 | SetMultiPitPump4StartLevelBand | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 120doc 00121 | SetMultiPitPump4HighWaterLevel | Multi-pit mode only. | UINT16 | × 0.01 | m | Read/write | ||
| HR | 121doc 00122 | PitPump1Control | UINT16 | Read/write | 0 = Auto; 1 = Forced start; 2 = Forced stop | ||||
| HR | 122doc 00123 | PitPump2Control | UINT16 | Read/write | 0 = Auto; 1 = Forced start; 2 = Forced stop | ||||
| HR | 123doc 00124 | PitPump3Control | UINT16 | Read/write | 0 = Auto; 1 = Forced start; 2 = Forced stop | ||||
| HR | 124doc 00125 | PitPump4Control | UINT16 | Read/write | 0 = Auto; 1 = Forced start; 2 = Forced stop | ||||
| HR | 202doc 00203 | PitMode | UINT16 | Read | 0 = Single-pit; 1 = Multi-pit | ||||
| HR | 203doc 00204 | SinglePitStopLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 204doc 00205 | SinglePitStartLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 205doc 00206 | SinglePitStartLevelBand | UINT16 | × 0.01 | m | Read | |||
| HR | 206doc 00207 | SinglePitHighWaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 207doc 00208 | MultiPitPump1StopLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 208doc 00209 | MultiPitPump1StartLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 209doc 00210 | MultiPitPump1StartLevelBand | UINT16 | × 0.01 | m | Read | |||
| HR | 210doc 00211 | MultiPitPump1HighWaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 211doc 00212 | MultiPitPump2StopLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 212doc 00213 | MultiPitPump2StartLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 213doc 00214 | MultiPitPump2StartLevelBand | UINT16 | × 0.01 | m | Read | |||
| HR | 214doc 00215 | MultiPitPump2HighWaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 215doc 00216 | MultiPitPump3StopLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 216doc 00217 | MultiPitPump3StartLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 217doc 00218 | MultiPitPump3StartLevelBand | UINT16 | × 0.01 | m | Read | |||
| HR | 218doc 00219 | MultiPitPump3HighWaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 219doc 00220 | MultiPitPump4StopLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 220doc 00221 | MultiPitPump4StartLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 221doc 00222 | MultiPitPump4StartLevelBand | UINT16 | × 0.01 | m | Read | |||
| HR | 222doc 00223 | MultiPitPump4HighWaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 223doc 00224 | PitPump1OperationMode | UINT16 | Read | 0 = Auto; 1 = Started; 2 = Stopped | ||||
| HR | 224doc 00225 | PitPump2OperationMode | UINT16 | Read | 0 = Auto; 1 = Started; 2 = Stopped | ||||
| HR | 225doc 00226 | PitPump3OperationMode | UINT16 | Read | 0 = Auto; 1 = Started; 2 = Stopped | ||||
| HR | 226doc 00227 | PitPump4OperationMode | UINT16 | Read | 0 = Auto; 1 = Started; 2 = Stopped | ||||
| HR | 227doc 00228 | AlarmCode | Grundfos alarm code of the pit (see manual section 14.2). | UINT16 | Read | ||||
| HR | 228doc 00229 | WarningCode | Grundfos warning code of the pit. | UINT16 | Read | ||||
| HR | 229doc 00230 | PitPumpsPresent | BITMAP16 | Read | bit 0 = Pump 1 present; bit 1 = Pump 2 present; bit 2 = Pump 3 present; bit 3 = Pump 4 present | ||||
| HR | 230doc 00231 | PitPumpsRunning | BITMAP16 | Read | bit 0 = Pump 1 running; bit 1 = Pump 2 running; bit 2 = Pump 3 running; bit 3 = Pump 4 running | ||||
| HR | 231doc 00232 | PitPumpsAlarm | BITMAP16 | Read | bit 0 = Pump 1 alarm; bit 1 = Pump 2 alarm; bit 2 = Pump 3 alarm; bit 3 = Pump 4 alarm | ||||
| HR | 232doc 00233 | PitPumpsCommFault | BITMAP16 | Read | bit 0 = Pump 1 communication fault; bit 1 = Pump 2 communication fault; bit 2 = Pump 3 communication fault; bit 3 = Pump 4 communication fault | ||||
| HR | 233doc 00234 | OperatingMode | Single-pit mode only. | UINT16 | Read | 0 = Standby; 1 = Startup delay; 2 = Pumping (level control); 5 = Stopped (level control); 9 = Manual control; 11 = Mains supply failure; 13 = Alarm on all enabled pumps; 14 = All pumps out of operation | |||
| HR | 234doc 00235 | MainStatus | BITMAP16 | Read | bit 0 = Warning in pump or pit; bit 1 = Alarm in pump or pit; bit 3 = Manual pump control enabled | ||||
| HR | 239doc 00240 | AlarmBits | BITMAP16 | Read | bit 0 = External fault signal; bit 1 = Communication fault, pump; bit 3 = Pump 1 fault; bit 4 = Pump 2 fault; bit 5 = Pump 3 fault; bit 6 = Pump 4 fault; bit 7 = Sensor limit 2 exceeded (high level); bit 8 = Setup conflict | ||||
| HR | 240doc 00241 | WarningBits | BITMAP16 | Read | bit 1 = Communication fault, pump; bit 2 = Verification error (ROM, FLASH); bit 8 = Setup conflict | ||||
| HR | 300doc 00301 | WaterLevel | Pit level estimated by the pumps; single-pit mode. | UINT16 | × 0.01 | m | Read | ||
| HR | 301doc 00302 | MaxWaterLevel | Highest level seen; reset with ResetHistory. | UINT16 | × 0.01 | m | Read | ||
| HR | 302doc 00303 | Power | UINT32 | ABCD | W | Read | |||
| HR | 304doc 00305 | EnergyTripCnt | Resettable with ResetHistory. | UINT32 | ABCD | kWh | Read | ||
| HR | 306doc 00307 | OnTimeCnt | CIU power-on time; cannot be reset. | UINT32 | ABCD | min | Read | ||
| HR | 308doc 00309 | OprTimeTripCnt | Time with one or more pumps running. | UINT32 | ABCD | min | Read | ||
| HR | 310doc 00311 | PumpOperationTimePct | Share of time pumping, last 30 days. | UINT16 | × 0.01 | % | Read | ||
| HR | 311doc 00312 | MultiPumpOperationTimePct | Share of pumping time with several pumps, 30 days. | UINT16 | × 0.01 | % | Read | ||
| HR | 312doc 00313 | MultiPumpOperationTimeMax | Longest multi-pump run, last 30 days. | UINT16 | s | Read | |||
| HR | 313doc 00314 | DigitalInput | BITMAP16 | Read | |||||
| HR | 400doc 00401 | Pump1.MotorTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 401doc 00402 | Pump1.ElectronicTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 402doc 00403 | Pump1.AverageLineVoltage | UINT16 | × 0.1 | V | Read | |||
| HR | 403doc 00404 | Pump1.AverageLineCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 404doc 00405 | Pump1.AverageLineCurrentLatest | Current during the last run. | UINT16 | × 0.1 | A | Read | ||
| HR | 405doc 00406 | Pump1.LineFrequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 406doc 00407 | Pump1.PhaseSequence | Boolean phase-sequence state. | UINT16 | Read | ||||
| HR | 407doc 00408 | Pump1.CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 408doc 00409 | Pump1.Power | UINT16 | W | Read | ||||
| HR | 409doc 00410 | Pump1.EnergyTripCounter | UINT32 | ABCD | kWh | Read | |||
| HR | 411doc 00412 | Pump1.WaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 412doc 00413 | Pump1.WaterLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 413doc 00414 | Pump1.MaxContinousTime | Longest continuous run, last 30 days. | UINT16 | min | Read | |||
| HR | 414doc 00415 | Pump1.TotalPoweredTime | UINT32 | ABCD | min | Read | |||
| HR | 416doc 00417 | Pump1.OperationTime | UINT32 | ABCD | min | Read | |||
| HR | 418doc 00419 | Pump1.OperationTimeTripCounter | UINT32 | ABCD | min | Read | |||
| HR | 420doc 00421 | Pump1.NumberOfStarts | UINT32 | ABCD | Read | ||||
| HR | 422doc 00423 | Pump1.NumberOfStartsTripCounter | UINT32 | ABCD | Read | ||||
| HR | 424doc 00425 | Pump1.AlarmCode | Grundfos alarm code (manual section 14.2). | UINT16 | Read | ||||
| HR | 425doc 00426 | Pump1.WarningCode | Grundfos warning code. | UINT16 | Read | ||||
| HR | 426doc 00427 | Pump1.OperatingMode | UINT16 | Read | 0 = Auto (power-on default); 1 = Forced start; 2 = Forced stop | ||||
| HR | 427doc 00428 | Pump1.Alarms | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 428doc 00429 | Pump1.Warnings | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 450doc 00451 | Pump2.MotorTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 451doc 00452 | Pump2.ElectronicTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 452doc 00453 | Pump2.AverageLineVoltage | UINT16 | × 0.1 | V | Read | |||
| HR | 453doc 00454 | Pump2.AverageLineCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 454doc 00455 | Pump2.AverageLineCurrentLatest | Current during the last run. | UINT16 | × 0.1 | A | Read | ||
| HR | 455doc 00456 | Pump2.LineFrequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 456doc 00457 | Pump2.PhaseSequence | Boolean phase-sequence state. | UINT16 | Read | ||||
| HR | 457doc 00458 | Pump2.CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 458doc 00459 | Pump2.Power | UINT16 | W | Read | ||||
| HR | 459doc 00460 | Pump2.EnergyTripCounter | UINT32 | ABCD | kWh | Read | |||
| HR | 461doc 00462 | Pump2.WaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 462doc 00463 | Pump2.WaterLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 463doc 00464 | Pump2.MaxContinousTime | Longest continuous run, last 30 days. | UINT16 | min | Read | |||
| HR | 464doc 00465 | Pump2.TotalPoweredTime | UINT32 | ABCD | min | Read | |||
| HR | 466doc 00467 | Pump2.OperationTime | UINT32 | ABCD | min | Read | |||
| HR | 468doc 00469 | Pump2.OperationTimeTripCounter | UINT32 | ABCD | min | Read | |||
| HR | 470doc 00471 | Pump2.NumberOfStarts | UINT32 | ABCD | Read | ||||
| HR | 472doc 00473 | Pump2.NumberOfStartsTripCounter | UINT32 | ABCD | Read | ||||
| HR | 474doc 00475 | Pump2.AlarmCode | Grundfos alarm code (manual section 14.2). | UINT16 | Read | ||||
| HR | 475doc 00476 | Pump2.WarningCode | Grundfos warning code. | UINT16 | Read | ||||
| HR | 476doc 00477 | Pump2.OperatingMode | UINT16 | Read | 0 = Auto (power-on default); 1 = Forced start; 2 = Forced stop | ||||
| HR | 477doc 00478 | Pump2.Alarms | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 478doc 00479 | Pump2.Warnings | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 500doc 00501 | Pump3.MotorTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 501doc 00502 | Pump3.ElectronicTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 502doc 00503 | Pump3.AverageLineVoltage | UINT16 | × 0.1 | V | Read | |||
| HR | 503doc 00504 | Pump3.AverageLineCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 504doc 00505 | Pump3.AverageLineCurrentLatest | Current during the last run. | UINT16 | × 0.1 | A | Read | ||
| HR | 505doc 00506 | Pump3.LineFrequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 506doc 00507 | Pump3.PhaseSequence | Boolean phase-sequence state. | UINT16 | Read | ||||
| HR | 507doc 00508 | Pump3.CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 508doc 00509 | Pump3.Power | UINT16 | W | Read | ||||
| HR | 509doc 00510 | Pump3.EnergyTripCounter | UINT32 | ABCD | kWh | Read | |||
| HR | 511doc 00512 | Pump3.WaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 512doc 00513 | Pump3.WaterLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 513doc 00514 | Pump3.MaxContinousTime | Longest continuous run, last 30 days. | UINT16 | min | Read | |||
| HR | 514doc 00515 | Pump3.TotalPoweredTime | UINT32 | ABCD | min | Read | |||
| HR | 516doc 00517 | Pump3.OperationTime | UINT32 | ABCD | min | Read | |||
| HR | 518doc 00519 | Pump3.OperationTimeTripCounter | UINT32 | ABCD | min | Read | |||
| HR | 520doc 00521 | Pump3.NumberOfStarts | UINT32 | ABCD | Read | ||||
| HR | 522doc 00523 | Pump3.NumberOfStartsTripCounter | UINT32 | ABCD | Read | ||||
| HR | 524doc 00525 | Pump3.AlarmCode | Grundfos alarm code (manual section 14.2). | UINT16 | Read | ||||
| HR | 525doc 00526 | Pump3.WarningCode | Grundfos warning code. | UINT16 | Read | ||||
| HR | 526doc 00527 | Pump3.OperatingMode | UINT16 | Read | 0 = Auto (power-on default); 1 = Forced start; 2 = Forced stop | ||||
| HR | 527doc 00528 | Pump3.Alarms | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 528doc 00529 | Pump3.Warnings | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 550doc 00551 | Pump4.MotorTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 551doc 00552 | Pump4.ElectronicTemperature | In 0.01 K (kelvin). | UINT16 | × 0.01 | K | Read | ||
| HR | 552doc 00553 | Pump4.AverageLineVoltage | UINT16 | × 0.1 | V | Read | |||
| HR | 553doc 00554 | Pump4.AverageLineCurrent | UINT16 | × 0.1 | A | Read | |||
| HR | 554doc 00555 | Pump4.AverageLineCurrentLatest | Current during the last run. | UINT16 | × 0.1 | A | Read | ||
| HR | 555doc 00556 | Pump4.LineFrequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 556doc 00557 | Pump4.PhaseSequence | Boolean phase-sequence state. | UINT16 | Read | ||||
| HR | 557doc 00558 | Pump4.CosPhi | UINT16 | × 0.01 | Read | ||||
| HR | 558doc 00559 | Pump4.Power | UINT16 | W | Read | ||||
| HR | 559doc 00560 | Pump4.EnergyTripCounter | UINT32 | ABCD | kWh | Read | |||
| HR | 561doc 00562 | Pump4.WaterLevel | UINT16 | × 0.01 | m | Read | |||
| HR | 562doc 00563 | Pump4.WaterLevelMax | UINT16 | × 0.01 | m | Read | |||
| HR | 563doc 00564 | Pump4.MaxContinousTime | Longest continuous run, last 30 days. | UINT16 | min | Read | |||
| HR | 564doc 00565 | Pump4.TotalPoweredTime | UINT32 | ABCD | min | Read | |||
| HR | 566doc 00567 | Pump4.OperationTime | UINT32 | ABCD | min | Read | |||
| HR | 568doc 00569 | Pump4.OperationTimeTripCounter | UINT32 | ABCD | min | Read | |||
| HR | 570doc 00571 | Pump4.NumberOfStarts | UINT32 | ABCD | Read | ||||
| HR | 572doc 00573 | Pump4.NumberOfStartsTripCounter | UINT32 | ABCD | Read | ||||
| HR | 574doc 00575 | Pump4.AlarmCode | Grundfos alarm code (manual section 14.2). | UINT16 | Read | ||||
| HR | 575doc 00576 | Pump4.WarningCode | Grundfos warning code. | UINT16 | Read | ||||
| HR | 576doc 00577 | Pump4.OperatingMode | UINT16 | Read | 0 = Auto (power-on default); 1 = Forced start; 2 = Forced stop | ||||
| HR | 577doc 00578 | Pump4.Alarms | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault | ||||
| HR | 578doc 00579 | Pump4.Warnings | BITMAP16 | Read | bit 0 = Phase sequence reversed; bit 1 = Overvoltage; bit 2 = Undervoltage; bit 3 = Overload; bit 4 = Blocked motor/pump; bit 6 = Motor temperature; bit 7 = Control electronics temperature; bit 8 = Temperature relay 1 (e.g. Klixon); bit 9 = Temperature relay 2 (e.g. thermistor); bit 10 = Verification error (ROM, FLASH); bit 12 = Sensor fault |
Notes on this map
- 32-bit values are HI/LO register pairs with the HI part at the lower address, so they are ABCD.
- All registers can be read with function 03 or 04 and are listed as holding registers. 0xFFFF means not available.
- Pumps 2-4 repeat the pump 1 layout at +50 (00451, 00501, 00551); checked against the printed pump 2-4 tables.
- Left out: register 00202, because its bit names (bit 0 AlarmInPumpOrPit, bit 1 WarningInPumpOrPit) contradict their descriptions; 00235 carries the same main status consistently and is listed instead. Also left out: the acknowledge register 00201, CIU 262-only cellular registers (RTC, 00236-00239) and user registers.
- Motor and electronics temperatures are printed in 0.01 K; no 273.15 offset is applied here.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)
What Modbus registers does the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) have?
This map lists 169 registers: 169 holding registers. 28 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The manual says registers numbered X are addressed in telegrams as X - 1 (00104 is sent as 103). Pump n's block starts at 00401 + 50 x (n-1).
What byte order does the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)?
Start with HR 230 PitPumpsRunning (Pumps running bits); HR 231 PitPumpsAlarm (Pumps in alarm bits); HR 234 MainStatus (Warning / alarm / manual summary); HR 300 WaterLevel (Pit water level); HR 100 PitControl (Reset and pump-down commands); HR 403 Pump1.AverageLineCurrent (Pump 1 current); HR 427 Pump1.Alarms (Pump 1 alarm bits).
How do I enable Modbus control of the Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus)?
Set the CIU 202 address with the hex rotary switches and the speed and parity with the DIP switches; no setting is needed in the pumps. Write the pit levels only in the mode selected by PitMode (00203).
Where is the official Grundfos SEG AUTOADAPT grinder pumps with CIU 202 / CIU 262 / CIU 502 (Modbus) Modbus documentation?
The source is Modbus for SEG AUTOADAPT - CIU 202 Modbus RTU, CIU 262 3G/4G Cellular, CIU 502 Ethernet for Modbus TCP - Functional profile and user manual (96846341 0119), revision 2019-01, published free by Grundfos at https://api.grundfos.com/literature/Grundfosliterature-6012945.pdf.
More Grundfos Modbus register maps
- Pump (booster system / multi-pump controller)
Grundfos Booster systems (Hydro MPC, Hydro Multi-E, Multi-B) via CIM 200 / CIM 500
Grundfos booster systems: Hydro MPC / Control MPC (CU 352), GENIECON MPC, Hydro Multi-B (CU 323), DDD (CU 354), Hydro Multi-E, TPED and MAGNA3-D twin pumps, with CIM/CIU 200, CIM/CIU 500 or SoftCIM.
Also known as: Hydro MPC, Control MPC, CU 352, GENIECON MPC, Hydro Multi-E, Hydro Multi-B, CU 323, DDD, CU 354, TPED, MAGNA3-D, CIM 200, CIM 500, SoftCIM Modbus TCP - Pump controller (wastewater lift station)
Grundfos Dedicated Controls (CU 361 / CU 362) with CIM 200 / CIM 260 / CIM 500 (Modbus)
Grundfos Dedicated Controls wastewater pit controller (CU 361 / CU 362, up to six pumps and a mixer) with a CIM 200 Modbus RTU, CIM 260 cellular or CIM 500 Modbus TCP module; functional profile 98393520 (2023-03).
Also known as: Dedicated Controls, CU 361, CU 362, CIM 200, CIM 260, CIM 500, 98393520 - Pump (circulator / E-pump / pump drive)
Grundfos E-pumps (MAGNA3, TPE, CRE, CUE) via CIM 200 / CIM 500
Grundfos E-pumps (CRE/CRNE/CRIE, MTRE, CHIE, CME, TPE, TPE Series 2000, NBE/NKE), CUE drives and MAGNA3 with a CIM/CIU 200, CIM/CIU 500 or built-in SoftCIM.
Also known as: MAGNA3, TPE, TPE Series 2000, CRE, CRNE, CRIE, MTRE, CHIE, CME, NBE, NKE, CUE, MGE, CIM 200, CIU 200, CIM 500, CIU 500, SoftCIM Modbus RTU - Pump protection / monitoring module (Sensor)
Grundfos IO 113 pump protection module (Modbus RTU)
Grundfos IO 113 interface module for wastewater and sewage pumps (with or without the SM 113 sensor board) set to Modbus with DIP switch 9; document edition 1.7, January 2015.
Also known as: IO113, IO 113 with SM 113, 98288208 - Pump motor protection relay
Grundfos MP 204 motor protector with CIU 200 / CIU 500 (Modbus)
Grundfos MP 204 electronic motor protector connected over GENIbus to a CIU 200 (Modbus RTU), CIU 250 (GSM/GPRS) or CIU 500 (Modbus TCP) box; functional profile 98393513 (2014-11).
Also known as: MP 204, CIU 200 Modbus RTU, CIU 250 GSM/GPRS, CIU 500 Modbus TCP, 98393513 - Pump (chemical dosing pump)
Grundfos SMART Digital DDA dosing pump (SoftCIM, CIM 200 / CIM 500)
Grundfos SMART Digital DDA dosing pumps: DDA model C with built-in SoftCIM Modbus RTU/TCP, and DDA XL (or others) through a CIM 200 Modbus RTU or CIM 500 Modbus TCP module in a CIU 900, per functional profile 98473491 (09.2026).
Also known as: DDA, DDA S, DDA XL, DDA-C, DDA model C, SMART Digital S, SMART Digital XL, CIM 200, CIM 500, 98473491
Other pumps register maps
- Thermostat / heat pump and unitary controller
Neptronic TUCB / TUHB Series universal wall-mount controller (Modbus RTU)
Neptronic TUCB24C6X2 (temperature) and TUHB24C6X2 (temperature and humidity) universal wall-mount controllers with 6 binary and 2 analog outputs, guide TUXB-Modbus Guide-190515.
Also known as: TUCB24C6X2, TUHB24C6X2, TUCB, TUHB, TUXB - Heat pump (air-to-water) Modbus interface
Toshiba BMS-IFMB0UEW-E Modbus RTU interface for ESTIA air-to-water heat pumps
Toshiba BMS-IFMB0UEW-E MB interface on ESTIA R410A 4 Series and 5 Series (WM type) and R32 1 Series (WM and AIO type) hydro units, user manual EEU-006 issued 31/05/2021.
Also known as: BMS-IFMB0UEW-E, ESTIA Modbus interface, Toshiba MB interface, EEU-006 - Pump system
Wilo SiFresh with CIF module Modbus RTU
Wilo SiFresh pumps fitted with the plug-in CIF module Modbus RTU (module firmware 1.00-99.99); registers needing a newer module are marked.
Also known as: Wilo-SiFresh - Heat pump Modbus interface
Airzone Aidoo Pro Modbus control for air-to-water heat pumps
Airzone Aidoo Pro units configured for Modbus output and connected to an air-to-water heat pump; register table 'Registers for Air-to-Water HP units' of the Aidoo - Modbus integration manual (v. 201).
Also known as: Aidoo Pro, Aidoo Pro Modbus air-to-water, Airzone Aidoo Modbus aerothermal - Heat pump
Ecoforest ecoGEO / ecoAIR heat pump (API HP24 Client, Modbus RTU)
Ecoforest ecoGEO, ecoGEO HP and ecoAIR heat pumps on software AWD24, WWD24, WWC24 or later, register list API HP24_V01.02 (heat pump list only; supervisor and source-manager lists not included).
Also known as: ecoGEO, ecoGEO B&C, ecoGEO HP, ecoAIR, AWD24, WWD24, WWC24, API HP24_V01.02 - Heat pump (packaged wall-mount / classroom unit)
Marvair MAH heat pump and VAH/VDH Vanguard control board (Modbus RTU)
Marvair MAH1020H-1060H and MAH2024H-2060H wall-mount heat pumps (I&O manual rev. 6); the GAH1024-1060 gas-heat AC manual (rev. 5) and the VAH/VDH Vanguard classroom unit appendices (08/2026) print the same table.
Also known as: MAH1020H, MAH1024H, MAH1030H, MAH1036H, MAH1042H, MAH1048H, MAH1060H, MAH2024H, MAH2030H, MAH2036H, MAH2042H, MAH2048H, MAH2060H, Vanguard VAH, Vanguard VDH, VAH2030, VDH2060, GAH1024, GAH1030, GAH1036, GAH1042, GAH1048, GAH1060, Marvair GAH, Scholar 2 VAH/VDH, Scholar QR VAH/VDH
All pumps Modbus register maps →
Source: Modbus for SEG AUTOADAPT - CIU 202 Modbus RTU, CIU 262 3G/4G Cellular, CIU 502 Ethernet for Modbus TCP - Functional profile and user manual · 96846341 0119 · rev. 2019-01. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.