- Home
- Modbus register maps
- IME
- Nemo 96HD multifunction meter (MF96001 / MF96021)
Power meter · Modbus register map
IME Nemo 96HD multifunction meter (MF96001 / MF96021) Modbus register map
Updated 17 November 2026
The Nemo 96HD is a modular 96x96 multifunction meter; with an RS-485 module it speaks Modbus/JBUS with functions 03 and 0x10. This map lists the integer measurement registers with fixed units: voltages and currents in mV/mA, power factor, frequency, THD and status values.
This page lists 40 Modbus registers for the IME Nemo 96HD multifunction meter (MF96001 / MF96021) — 0 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from IME’s own free documentation (linked below) and checked against it.
- Manufacturer
- IME
- Model
- Nemo 96HD multifunction meter (MF96001 / MF96021)
- Equipment type
- Power meter
- Registers
- 40 (0 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Documented addressing
- hexadecimal, 0-based
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- MF96001, MF96021, Nemo 96HD
Integration notes: IME Nemo 96HD multifunction meter (MF96001 / MF96021)
Read holding registers (function 03) from 0x1000 for voltages and currents in mV/mA, power factor, frequency and THD. Double words are high word first.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 4096 | Phase 1: phase voltage | UINT32 ABCD | Phase 1 voltage | Read |
| HR 4102 | Phase 1: current | UINT32 ABCD | Phase 1 current | Read |
| HR 4134 | Frequency | UINT16 | Frequency | Read |
| HR 4132 | 3-phase: power factor | INT16 | 3-phase power factor | Read |
Enable Modbus control & writes
Set the address, baud rate and parity on the meter (both are programmable). Only functions 03 and 0x10 are used. Setup writes need the unlock key 0x5AA5 written to 0x2700 first.
Byte order & addressing
- Only functions 03 and 0x10 are supported (no function 04).
- A single request may ask for at most 240 bytes of data (100 bytes on software older than 1.09).
- Voltages and currents are in mV and mA.
Network setup
- Baud rate and parity are programmable on the device; 8 data bits and 1 stop bit.
Watch out for
- Power and energy values are not in this map because their scale depends on the CT/VT ratio; see the protocol footnotes before using them.
IME Nemo 96HD multifunction meter (MF96001 / MF96021) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 4096doc 0x1000 | Phase 1: phase voltage | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4098doc 0x1002 | Phase 2: phase voltage | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4100doc 0x1004 | Phase 3: phase voltage | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4102doc 0x1006 | Phase 1: current | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4104doc 0x1008 | Phase 2: current | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4106doc 0x100a | Phase 3: current | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4108doc 0x100c | Neutral current | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4110doc 0x100e | Chained voltage: L1-L2 | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4112doc 0x1010 | Chained voltage: L2-L3 | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4114doc 0x1012 | Chained voltage: L3-L1 | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4132doc 0x1024 | 3-phase: power factor | INT16 | × 0.01 | Read | ||||
| HR | 4133doc 0x1025 | 3-phase: sector of power factor (cap or ind) | UINT16 | Read | 0 = PF = 1; 1 = Inductive; 2 = Capacitive | ||||
| HR | 4134doc 0x1026 | Frequency | UINT16 | × 0.1 | Hz | Read | |||
| HR | 4139doc 0x102b | Time counter for average power | UINT16 | min | Read | ||||
| HR | 4164doc 0x1044 | Phase 1: power factor | INT16 | × 0.01 | Read | ||||
| HR | 4165doc 0x1045 | Phase 2: power factor | INT16 | × 0.01 | Read | ||||
| HR | 4166doc 0x1046 | Phase 3: power factor | INT16 | × 0.01 | Read | ||||
| HR | 4167doc 0x1047 | Phase 1: power factor sector | UINT16 | Read | 0 = PF = 1; 1 = Inductive; 2 = Capacitive | ||||
| HR | 4168doc 0x1048 | Phase 2: power factor sector | UINT16 | Read | 0 = PF = 1; 1 = Inductive; 2 = Capacitive | ||||
| HR | 4169doc 0x1049 | Phase 3: power factor sector | UINT16 | Read | 0 = PF = 1; 1 = Inductive; 2 = Capacitive | ||||
| HR | 4170doc 0x104a | Phase 1: THD V1 | UINT16 | × 0.1 | % | Read | |||
| HR | 4171doc 0x104b | Phase 2: THD V2 | UINT16 | × 0.1 | % | Read | |||
| HR | 4172doc 0x104c | Phase 3: THD V3 | UINT16 | × 0.1 | % | Read | |||
| HR | 4173doc 0x104d | Phase 1: THD I1 | UINT16 | × 0.1 | % | Read | |||
| HR | 4174doc 0x104e | Phase 2: THD I2 | UINT16 | × 0.1 | % | Read | |||
| HR | 4175doc 0x104f | Phase 3: THD I3 | UINT16 | × 0.1 | % | Read | |||
| HR | 4176doc 0x1050 | Phase 1: I1 average | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4178doc 0x1052 | Phase 2: I2 average | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4180doc 0x1054 | Phase 3: I3 average | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4182doc 0x1056 | Phase 1: I1 peak maximum | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4184doc 0x1058 | Phase 2: I2 peak maximum | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4186doc 0x105a | Phase 3: I3 peak maximum | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4188doc 0x105c | (I1+I2+I3)/3 | UINT32 | ABCD | × 0.001 | A | Read | ||
| HR | 4190doc 0x105e | Phase 1: V1 min | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4192doc 0x1060 | Phase 2: V2 min | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4194doc 0x1062 | Phase 3: V3 min | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4196doc 0x1064 | Phase 1: V1 max | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4198doc 0x1066 | Phase 2: V2 max | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4200doc 0x1068 | Phase 3: V3 max | UINT32 | ABCD | × 0.001 | V | Read | ||
| HR | 4613doc 0x1205 | Voltages sequence diagnostic | UINT16 | Read | 1 = OK; 2 = Error |
Notes on this map
- Double-word values (UD_WORD/SD_WORD) are sent most significant word first; the protocol notes the meter can be set to big endian, little endian or swapped words, so check that setting if values look wrong.
- Left out: all power and energy registers, including the 0x15xx block; in this protocol their units depend on footnotes tied to the CT x VT ratio.
- Left out: setup parameters, device configuration words, the per-slot data areas, and any row whose printed unit does not fit the quantity (for example apparent power printed in W).
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the IME Nemo 96HD multifunction meter (MF96001 / MF96021)
What Modbus registers does the IME Nemo 96HD multifunction meter (MF96001 / MF96021) have?
This map lists 40 registers: 40 holding registers. 0 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the IME Nemo 96HD multifunction meter (MF96001 / MF96021) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Addresses are the hex word addresses sent as 'first WORD address' in the function 03 request, so they go on the wire unchanged.
What byte order does the IME Nemo 96HD multifunction meter (MF96001 / MF96021) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the IME Nemo 96HD multifunction meter (MF96001 / MF96021)?
Start with HR 4096 Phase 1: phase voltage (Phase 1 voltage); HR 4102 Phase 1: current (Phase 1 current); HR 4134 Frequency (Frequency); HR 4132 3-phase: power factor (3-phase power factor).
How do I enable Modbus control of the IME Nemo 96HD multifunction meter (MF96001 / MF96021)?
Set the address, baud rate and parity on the meter (both are programmable). Only functions 03 and 0x10 are used. Setup writes need the unlock key 0x5AA5 written to 0x2700 first.
Where is the official IME Nemo 96HD multifunction meter (MF96001 / MF96021) Modbus documentation?
The source is Communication Modbus protocol PR106 - MF96001/021 Nemo 96HD (PR106 rev. B), revision 2016-10-20, published free by IME at https://assets.legrand.com/pim/NP-FT-GT/PR106FR.pdf.
More IME Modbus register maps
- Energy meter (DIN-rail, single-phase)
IME Conto D1 single-phase energy meter (CE111)
IME Conto D1 single-phase meter, code CE111, per protocol PR133 (2025-02-24).
Also known as: CE111, Conto D1 - Power meter
IME Nemo 72Le multifunction meter (MF724)
IME Nemo 72Le 72x72 panel meter MF724 with RS-485, per protocol PR141 (software 1.04).
Also known as: MF724, Nemo 72Le - Power meter
IME Nemo 96HDe multifunction meter (MF96E06)
IME Nemo 96HDe panel meter MF96E06 with RS-485, per protocol PR145.
Also known as: MF96E06, Nemo 96HDe - Power meter
IME Nemo 96HDLe multifunction meter (MF964)
IME Nemo 96HDLe panel meter MF964 with RS-485, per protocol PR130 (software 5.08).
Also known as: MF964, Nemo 96HDLe - Power meter
IME Nemo 96HDLe with Rogowski coil input (KRNEMOHD)
IME Nemo 96HDLe for Rogowski coils, code KRNEMOHD, per protocol PR139 (software 1.03).
Also known as: KRNEMOHD - Power meter (DIN-rail)
IME Nemo D4-Le multifunction meter (MFD44)
IME Nemo D4-Le DIN-rail meter MFD44 with RS-485, per protocol PR129 (software 2.05).
Also known as: MFD44, Nemo D4-Le - Power meter (DIN-rail)
IME Nemo D4-Le with Rogowski coil input (KRNEMOD4)
IME Nemo D4-Le for Rogowski coils, code KRNEMOD4, per protocol PR140 (software 1.01).
Also known as: KRNEMOD4
Other power & energy meters register maps
- Energy meter
inepro Metering PRO1 single-phase energy meter (2026 PRO line)
PRO1-Mod (art. 1101) and PRO1-Mod-Ba (art. 1102, with RTC tariffs) from the 2026 PRO1 user manual version 1.3; the PRO1-S has no Modbus.
Also known as: PRO1-Mod, PRO1-Mod-Ba, PRO1 1U AC 45A Mo T MID, PRO1 1U AC 45A Mo T Ba MID, 1101, 1102 - Power meter (power analyser)
Janitza UMG 104 power analyser (RS-485 Modbus RTU)
UMG 104 DIN-rail power analyser, firmware 1.268, per address list 1.041.006.1.e (01/2023).
Also known as: UMG104, UMG 104, Janitza UMG104 - Power meter (power quality analyser)
Janitza UMG 604-PRO power analyser (Modbus RTU / Modbus TCP)
UMG 604-PRO from firmware release 5.028, per address list 1.033.034.e (08/2023).
Also known as: UMG604-PRO, UMG 604PRO, UMG604PRO, UMG 604-EP PRO, Janitza UMG 604 - Power meter (power quality analyser)
KMB systems SMC / SMY / SMZ / ARTIQ power analysers (Modbus manual v4.0)
KMB systems panel and DIN-rail meters and analysers with firmware 4.x, per 'Modbus-TCP and Modbus-RTU protocol documentation' (revision of January 19, 2023). Which blocks a model supports depends on the instrument and its firmware modules.
Also known as: SMC 133, SMC 144, PA 144, SML 133, SMM 133, SMC 118, SMY 133, SMY 134, SMP 133, SMZ 133, SMC 235, SMC 233, ARTIQ 235, ARTIQ 233, BC 235, BCPM 233, EMU 3, SMZ 244 - Pump (chemical metering pump)
LMI Excel XR series electronic metering pump (Modbus RTU)
LMI Excel XR electronic metering pumps fitted with the Modbus RTU interface (manual 55312 rev 04).
Also known as: Excel XR, LMI Excel XR, Milton Roy Excel XR, Excel XR Modbus - Energy meter (DIN-rail, single-phase, MID)
Lumel NMID11 / NMID12 / NMID13 single-phase energy meter
Modbus RTU versions of the NMID11, NMID12 and NMID13 meters (NMID11/NMID13 are the CT-connected models); the LITE and MBUS versions have no Modbus port.
Also known as: NMID11, NMID12, NMID13
All power & energy meters Modbus register maps →
Source: Communication Modbus protocol PR106 - MF96001/021 Nemo 96HD · PR106 rev. B · rev. 2016-10-20. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.