- Home
- Modbus register maps
- Red Lion
- PAXI counter / rate panel meter (Modbus)
Sensor (counter / rate panel meter) · Modbus register map
Red Lion PAXI counter / rate panel meter (Modbus) Modbus register map
Updated 17 November 2026
The PAXI is a counter and rate indicator with three counters (A, B, C), a rate channel, up to four setpoint outputs and an optional linear output card. Its serial port can run Modbus RTU or Modbus ASCII; this map covers the frequently used block (counts, rate, min/max, scale factors, count loads, setpoints, manual output control) plus counter A and rate settings.
This page lists 34 Modbus registers for the Red Lion PAXI counter / rate panel meter (Modbus) — 34 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Red Lion’s own free documentation (linked below) and checked against it.
- Manufacturer
- Red Lion
- Model
- PAXI counter / rate panel meter (Modbus)
- Equipment type
- Sensor (counter / rate panel meter)
- Registers
- 34 (34 writable)
- Transport
- Modbus RTU, Modbus ASCII
- Default unit ID
- 247
- Default serial
- 38400 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- PAXI, PAX I, Red Lion PAXI counter
Integration notes: Red Lion PAXI counter / rate panel meter (Modbus)
Read 40001-40012 in one request for counts, rate and min/max (high word first). Change setpoints or count loads by writing both words of 40019-40032; take direct control of outputs by setting MMR bits and then writing the SOR.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 0 | Counter A value | INT32 ABCD | Counter A value | Read/write |
| HR 6 | Rate value | INT32 ABCD | Rate value | Read/write |
| HR 24 | Setpoint 1 value | INT32 ABCD | Setpoint 1 | Read/write |
| HR 37 | Setpoint output register (SOR) | BITMAP16 | Setpoint output states | Read/write |
| HR 102 | Counter A decimal point | UINT16 | Counter A decimal point | Read/write |
| HR 163 | Rate decimal point | UINT16 | Rate decimal point | Read/write |
Enable Modbus control & writes
Set Serial Protocol (40301) to 1 for Modbus RTU or 2 for Modbus ASCII (factory setting is RTU). Serial settings 40301-40306 only take effect after writing 1 to Load Serial Settings (40309).
Byte order & addressing
- Values carry no decimal point; read the decimal point registers to scale them.
- The Slave ID block (41001+) reports a maximum of 64 registers per read or write.
Network setup
- Factory settings: Modbus RTU, 38400 baud, 8 data bits, no parity, address 247 (Modbus range 1-247).
- Baud (40302), data bits (40303), parity (40304), address (40305) and transmit delay (40306, 1 = 1 ms) are registers in this table; write 1 to 40309 to apply them, then switch the master to the new settings.
Watch out for
- Counter values are read/write: a write overwrites the count.
Red Lion PAXI counter / rate panel meter (Modbus) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 40001 | Counter A value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 2doc 40003 | Counter B value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 4doc 40005 | Counter C value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 6doc 40007 | Rate value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 8doc 40009 | Minimum (Lo) value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 10doc 40011 | Maximum (Hi) value | In display units without the decimal point (see the decimal point setting). | INT32 | ABCD | Read/write | |||
| HR | 12doc 40013 | Counter A scale factor | Active list (A or B); 1-999999, factory 100000 = 1.00000. | INT32 | ABCD | × 0.00001 | Read/write | ||
| HR | 14doc 40015 | Counter B scale factor | Active list (A or B); 1-999999, factory 100000 = 1.00000. | INT32 | ABCD | × 0.00001 | Read/write | ||
| HR | 16doc 40017 | Counter C scale factor | Active list (A or B); 1-999999, factory 100000 = 1.00000. | INT32 | ABCD | × 0.00001 | Read/write | ||
| HR | 18doc 40019 | Counter A count load | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 20doc 40021 | Counter B count load | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 22doc 40023 | Counter C count load | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 24doc 40025 | Setpoint 1 value | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 26doc 40027 | Setpoint 2 value | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 28doc 40029 | Setpoint 3 value | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 30doc 40031 | Setpoint 4 value | Active list (A or B); display units without the decimal point. | INT32 | ABCD | Read/write | |||
| HR | 35doc 40036 | Manual mode register (MMR) | 1 = manual, 0 = auto for each output. | BITMAP16 | Read/write | bit 0 = Linear output manual; bit 1 = S4 manual; bit 2 = S3 manual; bit 3 = S2 manual; bit 4 = S1 manual | |||
| HR | 36doc 40037 | Analog output register (AOR) | 0-4095; drives the linear output card only when MMR bit 0 = 1. | UINT16 | Read/write | ||||
| HR | 37doc 40038 | Setpoint output register (SOR) | Output states; writable only for outputs in manual (MMR). | BITMAP16 | Read/write | bit 0 = S4 on; bit 1 = S3 on; bit 2 = S2 on; bit 3 = S1 on | |||
| HR | 38doc 40039 | Reset output register | Write 1 to reset an output; the bit self-clears. | BITMAP16 | Read/write | bit 0 = Reset S4; bit 1 = Reset S3; bit 2 = Reset S2; bit 3 = Reset S1 | |||
| HR | 100doc 40101 | Counter A operating mode | UINT16 | Read/write | 0 = None; 1 = Count; 2 = Count up/down; 3 = Dual count up/down; 4 = Quad x1; 5 = Quad x2; 6 = Quad x4; 7 = Dual quad x1; 8 = Dual quad x2; 9 = Count x2; 10 = Count up/down x2; 11 = Dual count up/down x2 | ||||
| HR | 101doc 40102 | Counter A reset action | UINT16 | Read/write | 0 = Reset to zero; 1 = Reset to count load value | ||||
| HR | 102doc 40103 | Counter A decimal point | UINT16 | Read/write | 0 = 0; 1 = 0.0; 2 = 0.00; 3 = 0.000; 4 = 0.0000; 5 = 0.00000 | ||||
| HR | 103doc 40104 | Counter A scale multiplier | UINT16 | Read/write | 0 = x1; 1 = x0.1; 2 = x0.01 | ||||
| HR | 104doc 40105 | Counter A reset at power-up | UINT16 | Read/write | 0 = No; 1 = Yes | ||||
| HR | 105doc 40106 | Prescaler output enable | UINT16 | Read/write | 0 = No; 1 = Yes | ||||
| HR | 106doc 40107 | Prescaler scale value | 1-10000. | UINT16 | × 0.0001 | Read/write | |||
| HR | 158doc 40159 | Security code | 0-999. | UINT16 | Read/write | ||||
| HR | 160doc 40161 | Rate assignment | UINT16 | Read/write | 0 = No; 1 = Rate A; 2 = Rate B | ||||
| HR | 161doc 40162 | Rate low update time | UINT16 | × 0.1 | s | Read/write | |||
| HR | 162doc 40163 | Rate high update time | UINT16 | × 0.1 | s | Read/write | |||
| HR | 163doc 40164 | Rate decimal point | UINT16 | Read/write | 0 = 0; 1 = 0.0; 2 = 0.00; 3 = 0.000; 4 = 0.0000 | ||||
| HR | 167doc 40168 | Max (Hi) capture delay | UINT16 | × 0.1 | s | Read/write | |||
| HR | 168doc 40169 | Min (Lo) capture delay | UINT16 | × 0.1 | s | Read/write |
Notes on this map
- No direct Red Lion download of this table was found; the link is an unaltered copy of the Red Lion table (LP0897A) on a distributor's file host.
- 32-bit values are listed as a Hi word register followed by a Lo word register, so high word first (ABCD). Limits such as -99999999 show they are signed.
- '1 = 1 display unit' means the integer is the displayed value without its decimal point; apply the counter or rate decimal point setting yourself.
- Scale factor scaling (1 = 0.00001) is printed in the A/B list section (40051+) for the same parameter and applied here to the active-list copies at 40013-40018.
- Left out: A/B list copies 40051-40090, counter B/C settings, user input and function key actions, display lock-outs, linearizer points and setpoint output settings (40221+).
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Red Lion PAXI counter / rate panel meter (Modbus)
What Modbus registers does the Red Lion PAXI counter / rate panel meter (Modbus) have?
This map lists 34 registers: 34 holding registers. 34 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Red Lion PAXI counter / rate panel meter (Modbus) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are listed as 4xxxx holding registers (40001 = first). Request 40001 as address 0.
What byte order does the Red Lion PAXI counter / rate panel meter (Modbus) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Red Lion PAXI counter / rate panel meter (Modbus)?
Start with HR 0 Counter A value (Counter A value); HR 6 Rate value (Rate value); HR 24 Setpoint 1 value (Setpoint 1); HR 37 Setpoint output register (SOR) (Setpoint output states); HR 102 Counter A decimal point (Counter A decimal point); HR 163 Rate decimal point (Rate decimal point).
How do I enable Modbus control of the Red Lion PAXI counter / rate panel meter (Modbus)?
Set Serial Protocol (40301) to 1 for Modbus RTU or 2 for Modbus ASCII (factory setting is RTU). Serial settings 40301-40306 only take effect after writing 1 to Load Serial Settings (40309).
Where is the official Red Lion PAXI counter / rate panel meter (Modbus) Modbus documentation?
The source is PAXI Modbus Register Table (LP0897A), revision 2012-07-10. Red Lion doesn't publish it on its own website, so this map was re-typed from a free copy at https://cdn.logic-control.com/docs/red-lion/Datasheets/PAXI%20Modbus%20Register%20Table.pdf. It may be an older revision, so check it against the live unit.
More Red Lion Modbus register maps
- Thermostat / temperature and process PID controller
Red Lion PAX2C temperature/process PID controller (Modbus RTU/ASCII)
PAX2C version 2.0 register table (LP0905F, 2017-02-27); the FlexCard (PX2FCA0/PX2FCA1) blocks of the same table are not included.
Also known as: PAX2CHZVR, PAX2C00000, PX2FCA0, PX2FCA1 - Sensor (counter / rate panel meter)
Red Lion PAX2D counter / rate panel meter (Modbus)
PAX2D dual counter / rate meter, per register table LP0930A (4/11/13).
Also known as: PAX2D, PAX2 D, Red Lion PAX2D counter
Other power & energy meters register maps
- Energy meter
Rishabh Instruments RISH ED11XX / EC11XX / ER11XX single-phase DIN-rail energy meters
Rishabh RISH ED11XX (direct), EC11XX (CT) and ER11XX (RJ12 CT) single-phase DIN-rail meters in their Modbus (x1) versions, per operating manual DMAN-00IM-1071 Rev. M.
Also known as: RISH ED11X1, RISH EC11X1, RISH ER11X1, ED1111, EC1111, ER1111, RISH ED11XX, RISH EC11XX, RISH ER11XX - Energy meter (DC)
Rishabh Instruments RISH EM DC 6001 / 6002 multi-channel DC energy meter
Rishabh RISH EM DC 6001 / 6002 multi-channel DC energy meters with RS-485 Modbus, per interface definition 2-60-006-00-00627 Rev. 0 (10/2015).
Also known as: RISH EM DC 6001, RISH EM DC 6002, EM DC 6001, EM DC 6002 - Power meter (multi-circuit energy meter)
Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
RISH Multiload Monitor (12 current channels, 4 voltage channels) per interface definition DMAN-00IM-0795 Rev A (08/2020).
Also known as: RISH ML 1400, RISH ML 1410, RISH MLM, Multiload Monitor - Power meter (power quality analyzer)
SATEC PM174 powermeter and power quality analyzer
SATEC PM174 from firmware 24.3.1, per Modbus reference guide BG0414 Rev. A7 (April 2013).
Also known as: PM174, SATEC PM174, PM 174 - Power meter
Seneca T203PM single-phase AC/DC power meter (Modbus RTU)
T203PM100-MU / T203PM300-MU / T203PM600-MU per user manual MI00571-3-EN.
Also known as: T203PM100-MU, T203PM300-MU, T203PM600-MU, T203PM-MU, T-203PM - Power meter (power quality)
Siemens SICAM P850 / P855 power monitoring and PQ device
SICAM P850 / P855 (7KG85x) with Modbus TCP or Modbus RTU, firmware V3.11, per communication manual E50417-C1040-C482-B1 (05.2024).
Also known as: 7KG85, 7KG85X, SICAM P850, SICAM P855
All power & energy meters Modbus register maps →
Source: PAXI Modbus Register Table · LP0897A · rev. 2012-07-10 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.