- Home
- Modbus register maps
- Rishabh Instruments
- RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
Power meter (multi-circuit energy meter) · Modbus register map
Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) Modbus register map
Updated 17 November 2026
The RISH ML 1400/1410 is a 96 x 96 panel meter that measures up to 12 load circuits from 4 voltage inputs. Every measured value is a 32-bit IEEE float available in both the 3X and 4X tables. This map lists the per-channel instantaneous values (voltage, current, W, VA, VAr, PF, angle), frequency and the core comms settings.
This page lists 82 Modbus registers for the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) — 3 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Rishabh Instruments’s own free documentation (linked below) and checked against it.
- Manufacturer
- Rishabh Instruments
- Model
- RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
- Equipment type
- Power meter (multi-circuit energy meter)
- Registers
- 82 (3 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- RISH ML 1400, RISH ML 1410, RISH MLM, Multiload Monitor
Integration notes: Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
Read the 12 channel currents and powers with function 04 from wire 12 and 36 as ABCD floats; voltages start at wire 0 and frequency is at wire 1468.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | Voltage L1 | FLOAT32 ABCD | Voltage L1 | Read |
| IR 12 | Current channel 1 | FLOAT32 ABCD | Current channel 1 | Read |
| IR 36 | W channel 1 | FLOAT32 ABCD | W channel 1 | Read |
| IR 108 | PF channel 1 | FLOAT32 ABCD | PF channel 1 | Read |
| IR 1468 | Frequency | FLOAT32 ABCD | Frequency | Read |
Enable Modbus control & writes
Set address, baud rate and parity in the meter's communication parameter screen (or the RS485 setup and node address registers).
Byte order & addressing
- Every value is a 2-register float, even settings.
- Printed decimal addresses have typos on one page; trust the hex column.
Network setup
- RS-485, 4800-57600 bps, up to 32 meters per segment.
- Allow 300 ms response time before retrying.
Watch out for
- Broadcast (address 0) is not supported.
- Energy unit and divisor are configurable; check them before scaling energies.
Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 / 40001 (hex 0000, parameter 1) | Voltage L1 | FLOAT32 | ABCD | V | Read | |||
| IR | 2doc 30003 / 40003 (hex 0002, parameter 2) | Voltage L2 | FLOAT32 | ABCD | V | Read | |||
| IR | 4doc 30005 / 40005 (hex 0004, parameter 3) | Voltage L3 | FLOAT32 | ABCD | V | Read | |||
| IR | 6doc 30007 / 40007 (hex 0006, parameter 4) | Voltage L12 | FLOAT32 | ABCD | V | Read | |||
| IR | 8doc 30009 / 40009 (hex 0008, parameter 5) | Voltage L23 | FLOAT32 | ABCD | V | Read | |||
| IR | 10doc 30011 / 40011 (hex 000A, parameter 6) | Voltage L31 | FLOAT32 | ABCD | V | Read | |||
| IR | 12doc 30013 / 40013 (hex 000C, parameter 7) | Current channel 1 | FLOAT32 | ABCD | A | Read | |||
| IR | 14doc 30015 / 40015 (hex 000E, parameter 8) | Current channel 2 | FLOAT32 | ABCD | A | Read | |||
| IR | 16doc 30017 / 40017 (hex 0010, parameter 9) | Current channel 3 | FLOAT32 | ABCD | A | Read | |||
| IR | 18doc 30019 / 40019 (hex 0012, parameter 10) | Current channel 4 | FLOAT32 | ABCD | A | Read | |||
| IR | 20doc 30021 / 40021 (hex 0014, parameter 11) | Current channel 5 | FLOAT32 | ABCD | A | Read | |||
| IR | 22doc 30023 / 40023 (hex 0016, parameter 12) | Current channel 6 | FLOAT32 | ABCD | A | Read | |||
| IR | 24doc 30025 / 40025 (hex 0018, parameter 13) | Current channel 7 | FLOAT32 | ABCD | A | Read | |||
| IR | 26doc 30027 / 40027 (hex 001A, parameter 14) | Current channel 8 | FLOAT32 | ABCD | A | Read | |||
| IR | 28doc 30029 / 40029 (hex 001C, parameter 15) | Current channel 9 | FLOAT32 | ABCD | A | Read | |||
| IR | 30doc 30031 / 40031 (hex 001E, parameter 16) | Current channel 10 | FLOAT32 | ABCD | A | Read | |||
| IR | 32doc 30033 / 40033 (hex 0020, parameter 17) | Current channel 11 | FLOAT32 | ABCD | A | Read | |||
| IR | 34doc 30035 / 40035 (hex 0022, parameter 18) | Current channel 12 | FLOAT32 | ABCD | A | Read | |||
| IR | 36doc 30037 / 40037 (hex 0024, parameter 19) | W channel 1 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 38doc 30039 / 40039 (hex 0026, parameter 20) | W channel 2 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 40doc 30041 / 40041 (hex 0028, parameter 21) | W channel 3 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 42doc 30043 / 40043 (hex 002A, parameter 22) | W channel 4 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 44doc 30045 / 40045 (hex 002C, parameter 23) | W channel 5 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 46doc 30047 / 40047 (hex 002E, parameter 24) | W channel 6 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 48doc 30049 / 40049 (hex 0030, parameter 25) | W channel 7 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 50doc 30051 / 40051 (hex 0032, parameter 26) | W channel 8 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 52doc 30053 / 40053 (hex 0034, parameter 27) | W channel 9 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 54doc 30055 / 40055 (hex 0036, parameter 28) | W channel 10 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 56doc 30057 / 40057 (hex 0038, parameter 29) | W channel 11 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 58doc 30059 / 40059 (hex 003A, parameter 30) | W channel 12 | Active power of the load on this channel. | FLOAT32 | ABCD | W | Read | ||
| IR | 60doc 30061 / 40061 (hex 003C, parameter 31) | VA channel 1 | FLOAT32 | ABCD | VA | Read | |||
| IR | 62doc 30063 / 40063 (hex 003E, parameter 32) | VA channel 2 | FLOAT32 | ABCD | VA | Read | |||
| IR | 64doc 30065 / 40065 (hex 0040, parameter 33) | VA channel 3 | FLOAT32 | ABCD | VA | Read | |||
| IR | 66doc 30067 / 40067 (hex 0042, parameter 34) | VA channel 4 | FLOAT32 | ABCD | VA | Read | |||
| IR | 68doc 30069 / 40069 (hex 0044, parameter 35) | VA channel 5 | FLOAT32 | ABCD | VA | Read | |||
| IR | 70doc 30071 / 40071 (hex 0046, parameter 36) | VA channel 6 | FLOAT32 | ABCD | VA | Read | |||
| IR | 72doc 30073 / 40073 (hex 0048, parameter 37) | VA channel 7 | FLOAT32 | ABCD | VA | Read | |||
| IR | 74doc 30075 / 40075 (hex 004A, parameter 38) | VA channel 8 | FLOAT32 | ABCD | VA | Read | |||
| IR | 76doc 30077 / 40077 (hex 004C, parameter 39) | VA channel 9 | FLOAT32 | ABCD | VA | Read | |||
| IR | 78doc 30079 / 40079 (hex 004E, parameter 40) | VA channel 10 | FLOAT32 | ABCD | VA | Read | |||
| IR | 80doc 30081 / 40081 (hex 0050, parameter 41) | VA channel 11 | FLOAT32 | ABCD | VA | Read | |||
| IR | 82doc 30083 / 40083 (hex 0052, parameter 42) | VA channel 12 | FLOAT32 | ABCD | VA | Read | |||
| IR | 84doc 30085 / 40085 (hex 0054, parameter 43) | VAr channel 1 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 86doc 30087 / 40087 (hex 0056, parameter 44) | VAr channel 2 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 88doc 30089 / 40089 (hex 0058, parameter 45) | VAr channel 3 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 90doc 30091 / 40091 (hex 005A, parameter 46) | VAr channel 4 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 92doc 30093 / 40093 (hex 005C, parameter 47) | VAr channel 5 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 94doc 30095 / 40095 (hex 005E, parameter 48) | VAr channel 6 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 96doc 30097 / 40097 (hex 0060, parameter 49) | VAr channel 7 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 98doc 30099 / 40099 (hex 0062, parameter 50) | VAr channel 8 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 100doc 30101 / 40101 (hex 0064, parameter 51) | VAr channel 9 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 102doc 30103 / 40103 (hex 0066, parameter 52) | VAr channel 10 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 104doc 30105 / 40105 (hex 0068, parameter 53) | VAr channel 11 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 106doc 30107 / 40107 (hex 006A, parameter 54) | VAr channel 12 | FLOAT32 | ABCD | VAr | Read | |||
| IR | 108doc 30109 / 40109 (hex 006C, parameter 55) | PF channel 1 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 110doc 30111 / 40111 (hex 006E, parameter 56) | PF channel 2 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 112doc 30113 / 40113 (hex 0070, parameter 57) | PF channel 3 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 114doc 30115 / 40115 (hex 0072, parameter 58) | PF channel 4 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 116doc 30117 / 40117 (hex 0074, parameter 59) | PF channel 5 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 118doc 30119 / 40119 (hex 0076, parameter 60) | PF channel 6 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 120doc 30121 / 40121 (hex 0078, parameter 61) | PF channel 7 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 122doc 30123 / 40123 (hex 007A, parameter 62) | PF channel 8 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 124doc 30125 / 40125 (hex 007C, parameter 63) | PF channel 9 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 126doc 30127 / 40127 (hex 007E, parameter 64) | PF channel 10 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 128doc 30129 / 40129 (hex 0080, parameter 65) | PF channel 11 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 130doc 30130 / 40130 (hex 0082, parameter 66) | PF channel 12 | Power factor. | FLOAT32 | ABCD | Read | |||
| IR | 132doc 30131 / 40131 (hex 0084, parameter 67) | Angle channel 1 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 134doc 30133 / 40133 (hex 0086, parameter 68) | Angle channel 2 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 136doc 30135 / 40135 (hex 0088, parameter 69) | Angle channel 3 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 138doc 30137 / 40137 (hex 008A, parameter 70) | Angle channel 4 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 140doc 30139 / 40139 (hex 008C, parameter 71) | Angle channel 5 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 142doc 30141 / 40141 (hex 008E, parameter 72) | Angle channel 6 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 144doc 30143 / 40143 (hex 0090, parameter 73) | Angle channel 7 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 146doc 30145 / 40145 (hex 0092, parameter 74) | Angle channel 8 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 148doc 30147 / 40147 (hex 0094, parameter 75) | Angle channel 9 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 150doc 30149 / 40149 (hex 0096, parameter 76) | Angle channel 10 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 152doc 30151 / 40151 (hex 0098, parameter 77) | Angle channel 11 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 154doc 30153 / 40153 (hex 009A, parameter 78) | Angle channel 12 | Phase angle of the channel. | FLOAT32 | ABCD | Read | |||
| IR | 1468doc 31469 / 41469 (hex 05BC, parameter 735) | Frequency | FLOAT32 | ABCD | Hz | Read | |||
| HR | 6006doc 46007 (hex 1776) | RS485 setup code | Baud/parity/stop-bit code from the manual's table 9. | FLOAT32 | ABCD | Read/write | |||
| HR | 6008doc 46009 (hex 1778) | Node address | 1-247. | FLOAT32 | ABCD | Read/write | |||
| HR | 6010doc 46011 (hex 177A) | Word order | Write 2141.0 in the order you want floats sent. | FLOAT32 | ABCD | Read/write |
Notes on this map
- Floats are sent most significant byte first by default; the example reply 43 5B 41 21 decodes to 219.254 V, so ABCD. Writing 2141.0 to the word-order register (46011) in reversed order switches the meter to CDAB for all floats.
- Each value is in both the 3X table (function 04) and the 4X table (function 03); only the 3X copy is listed.
- Table 1 prints the wrong decimal 3X/4X numbers for parameters 66-84: parameter 66 is printed one lower (30130, hex 0082) and parameters 67-84 two lower (e.g. 30131 for Angle channel 1, hex 0084). The hex column runs 2 x (parameter - 1) without a break and matches both section 3.1 example frames (Voltage L2 at 00 02, W channel 2 at 00 26), so this map uses the hex address.
- Energy, demand and overflow-count registers are left out: the energy unit (Wh/kWh/MWh) and divisor are user settings (46091 and related), so a fixed unit cannot be given.
- Settings registers in Table 3 are also floats; only address, RS485 code and word order are listed. Writes need function 16 with both registers.
- Channel quantities depend on the channel mode (3P4W, 3P3W, 1P2W, RCM, NC) set for each channel group.
- Reading part of a float returns exception 02. Keep each request to 120 parameters (240 registers) or fewer.
- The user-assignable register illustration near the end of section 3 shows parameter addresses 2 higher than Table 1 (e.g. Voltage L2 as 0x0004). The 3.1 example frames and their decoded replies agree with Table 1, so Table 1 is used.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
What Modbus registers does the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) have?
This map lists 82 registers: 79 input registers, 3 holding registers. 3 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Table 1 prints 30001/40001-style numbers plus a hex start-address column. The manual's example reads Voltage L2 (30003, parameter 2) at start address 00 02 and W channel 2 (40039, parameter 20) at 00 26, so subtract 30001 or 40001. Where the printed decimal and the hex column disagree (parameters 66-84), this map follows the hex column, which matches the rule wire = 2 x (parameter - 1).
What byte order does the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)?
Start with IR 0 Voltage L1 (Voltage L1); IR 12 Current channel 1 (Current channel 1); IR 36 W channel 1 (W channel 1); IR 108 PF channel 1 (PF channel 1); IR 1468 Frequency (Frequency).
How do I enable Modbus control of the Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)?
Set address, baud rate and parity in the meter's communication parameter screen (or the RS485 setup and node address registers).
Where is the official Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU) Modbus documentation?
The source is Interface Definition RISH MLM Digital Multifunction Instrument (DMAN-00IM-0795 Rev A), revision 2020-08, published free by Rishabh Instruments at https://rishabh.co.in/uploads/product/rish-ml-1400-ml-1410-multiload-monitor-126/ID-MLM.pdf.
More Rishabh Instruments Modbus register maps
- Energy meter (DC)
Rishabh Instruments RISH DC2111 MOD single-channel DC energy meter
Rishabh RISH DC2111 MOD single-channel DC energy meters with RS-485 Modbus, per interface definition DMAN-00IM-1669 Rev. D (08/25).
Also known as: RISH DC2111 MOD, DC2111 - Energy meter
Rishabh Instruments RISH Delta Energy NX multifunction energy meter
Rishabh RISH Delta Energy NX panel energy meters with RS-485 Modbus RTU, per the operating manual on the product page (standard CT version).
Also known as: RISH Delta Energy NX, Delta Energy NX, RISH Delta Energy - Power meter
Rishabh Instruments RISH Delta Power NX multifunction power meter
Rishabh RISH Delta Power NX programmable panel meters with RS-485 Modbus RTU, per operating manual AMAN-00IM-0117 Rev. E.
Also known as: RISH Delta Power NX, Delta Power NX, RISH Delta Power - Power meter
Rishabh Instruments RISH Delta VAF NX volt/amp/frequency panel meter
Rishabh RISH Delta VAF NX programmable panel meters with RS-485 Modbus RTU, per operating manual AMAN-00IM-0118 Rev. F.
Also known as: RISH Delta VAF NX, Delta VAF NX, RISH Delta VAF - Power meter (demand controller)
Rishabh Instruments RISH DMCi touch-screen demand controller with TOD
Rishabh RISH DMCi 96 x 96 mm touch-screen demand controllers with the optional RS-485 Modbus output, per interface definition DMAN-00IM-0578 Rev. A (09/16).
Also known as: RISH DMCi, DMCi, Rish DMCi demand controller - Energy meter
Rishabh Instruments RISH EC43xx / ER43xx DIN-rail energy meters
Rishabh RISH EC43xx and ER43xx DIN-rail digital energy meters with RS-485 Modbus, per interface definition DMAN-00IM-09xx Rev. F (11/25).
Also known as: EC4311, EC4321, ER4311, ER4321, RISH EC43X1, EC43XX, ER43XX - Energy meter
Rishabh Instruments RISH ED11XX / EC11XX / ER11XX single-phase DIN-rail energy meters
Rishabh RISH ED11XX (direct), EC11XX (CT) and ER11XX (RJ12 CT) single-phase DIN-rail meters in their Modbus (x1) versions, per operating manual DMAN-00IM-1071 Rev. M.
Also known as: RISH ED11X1, RISH EC11X1, RISH ER11X1, ED1111, EC1111, ER1111, RISH ED11XX, RISH EC11XX, RISH ER11XX - Energy meter
Rishabh Instruments RISH ED21XX / EC21XX / ER21XX single-phase energy meters
Rishabh RISH ED21XX (direct), EC21XX (CT) and ER21XX (RJ12 CT) single-phase meters in their Modbus versions, per operating manual DMAN-00IM-1073 Rev. M.
Also known as: RISH ED21X1, RISH EC21X1, RISH ER21X1, RISH ED21XX, RISH EC21XX, RISH ER21XX - Energy meter
Rishabh Instruments RISH EM 1320 / 1330 / 1340 / 2340 programmable energy meters
Rishabh RISH EM 1320/1330/1340 and EM 2320/2330/2340 panel energy meters with RS-485 Modbus, per interface definition DMAN-00IM-0721 Rev. B (06/2020). Rows marked 'only 2340' apply to the dual-source EM 2340.
Also known as: RISH EM 1320, RISH EM 1330, RISH EM 1340, RISH EM 2320, RISH EM 2330, RISH EM 2340, EM2340DS - Energy meter
Rishabh Instruments RISH EM 3490 DS dual-source (utility/generator) energy meter
Rishabh RISH EM 3490 DS dual-source energy meters (separate utility and generator energy) with RS-485 Modbus, per manual Rev G.
Also known as: RISH EM 3490 DS, EM3490DS, EM 3490DS - Energy meter
Rishabh Instruments RISH EM 3490 SS single-phase energy meter
Rishabh RISH EM 3490 SS single-phase energy meters with the optional RS-485 Modbus output, per the 1-phase manual Rev D.
Also known as: RISH EM 3490 SS 1P, EM3490SS 1P, EM 3490 SS single-phase - Energy meter
Rishabh Instruments RISH EM 3490 SS three-phase single-source energy meter
Rishabh RISH EM 3490 SS three-phase energy meters with the optional RS-485 Modbus output, per the 3-phase manual Rev E.
Also known as: RISH EM 3490 SS 3P, EM3490SS 3P, EM 3490 SS three-phase - Energy meter (DC)
Rishabh Instruments RISH EM DC 6000 programmable DC energy meter
Rishabh RISH EM DC 6000 single-channel programmable DC energy meters with RS-485 Modbus, per interface definition DMAN-00IM-0862 Rev. 0 (12/2020).
Also known as: RISH EM DC 6000, EMDC 6000, EM DC6000 - Energy meter (DC)
Rishabh Instruments RISH EM DC 6001 / 6002 multi-channel DC energy meter
Rishabh RISH EM DC 6001 / 6002 multi-channel DC energy meters with RS-485 Modbus, per interface definition 2-60-006-00-00627 Rev. 0 (10/2015).
Also known as: RISH EM DC 6001, RISH EM DC 6002, EM DC 6001, EM DC 6002 - Power meter
Rishabh Instruments RISH LM 1340 multifunction meter
Rishabh RISH LM 1340 panel multifunction instruments with RS-485 Modbus, per interface definition DMAN-00IM-0923 Rev. D (03/2026).
Also known as: RISH LM 1340, LM1340 - Power meter
Rishabh Instruments RISH LM 1360 load manager (LM 13xx)
Rishabh RISH LM 1360 panel meters with RS-485 Modbus, per interface definition DMAN-00IM-0662 Rev. D (01/2024).
Also known as: RISH LM 1360, LM1360, LM 13xx, LM1360 RJ12 - Power meter
Rishabh Instruments RISH LM 1380 multifunction meter
Rishabh RISH LM 1380 panel multifunction instruments with RS-485 Modbus, per interface definition DMAN-00IM-0925 Rev. A (04/2022).
Also known as: RISH LM 1380, LM1380 - Power meter
Rishabh Instruments RISH LM1360+ RJ12 smart energy meter
Rishabh RISH LM1360 PLUS RJ12 smart energy meters (RJ12 CT inputs) with RS-485 Modbus, per interface definition DMAN-00IM-0923 Rev. A (01/2026).
Also known as: RISH LM 1360+, LM1360 PLUS RJ12, LM1360+ - Power meter
Rishabh Instruments RISH Master 3440 (class 0.2S) multifunction meter
Rishabh RISH Master 3440 class 0.2S panel meters with RS-485 Modbus, per interface definition DMAN-00IM-0711 Rev. C (05/2019).
Also known as: RISH Master 3440, RM3440, Master 3440 0.2S - Power meter
Rishabh Instruments RISH Master 3440i / 3440iDL (class 0.2S) touch-screen meter
Rishabh RISH Master 3440i and 3440iDL touch-screen class 0.2S meters with RS-485 Modbus, per interface definition DMAN-00IM-0712 Rev. F (10/2026).
Also known as: RISH Master 3440i, RISH Master 3440iDL, RM3440i, RM3440iDL - Power meter (power factor controller)
Rishabh Instruments RISH PFC 96 / PFC 144 automatic power factor controller
Rishabh RISH PFC 96 and PFC 144 automatic power factor (APFC) controllers with RS-485 Modbus RTU, per interface definition version D (12/18).
Also known as: RISH PFC 96, RISH PFC 144, PFC96, PFC144, RISH PFC-12, APFC
Other power & energy meters register maps
- Power meter (power quality analyzer)
SATEC PM174 powermeter and power quality analyzer
SATEC PM174 from firmware 24.3.1, per Modbus reference guide BG0414 Rev. A7 (April 2013).
Also known as: PM174, SATEC PM174, PM 174 - Power meter
Seneca T203PM single-phase AC/DC power meter (Modbus RTU)
T203PM100-MU / T203PM300-MU / T203PM600-MU per user manual MI00571-3-EN.
Also known as: T203PM100-MU, T203PM300-MU, T203PM600-MU, T203PM-MU, T-203PM - Power meter (power quality)
Siemens SICAM P850 / P855 power monitoring and PQ device
SICAM P850 / P855 (7KG85x) with Modbus TCP or Modbus RTU, firmware V3.11, per communication manual E50417-C1040-C482-B1 (05.2024).
Also known as: 7KG85, 7KG85X, SICAM P850, SICAM P855 - Power meter (branch circuit monitoring)
ABB CMS-700 circuit monitoring system control unit (Modbus RTU / TCP)
ABB CMS-700 control unit with up to 96 CMS branch current sensors, per the CMS-700 user manual (Modbus and SNMP mapping chapter).
Also known as: CMS-700, CMS700, ABB CMS-700, CMS-700 control unit - Power meter (circuit breaker trip unit)
ABB SACE PR122/P, PR123/P, PR332/P, PR333/P trip units with PR120/D-M or PR330/D-M (Modbus RTU)
ABB SACE PR122/P and PR123/P (Emax) and PR332/P and PR333/P (Emax X1, Tmax T7, Tmax T8) protection releases with the Modbus RTU communication module, per 1SDH000556R0001.
Also known as: PR122/P, PR123/P, PR332/P, PR333/P, PR120/D-M, PR330/D-M, Emax PR122, Emax PR123, Tmax T7 PR332, Emax X1 PR333, Tmax T8 PR332 - Energy meter (thermal / BTU meter)
Belimo Thermal Energy Meter (TEM) DN 15-50, Version 4 (Modbus RTU / TCP)
Belimo Thermal Energy Meter DN 15...50 version 4 (22PE..-1U.., 22PF-..U..), interface description V4.2.0 edition 2025-11.
Also known as: 22PE-1U, 22PEM-1UC, 22PE..-1U.., 22PF, Belimo Thermal Energy Meter, Belimo TEM
All power & energy meters Modbus register maps →
Source: Interface Definition RISH MLM Digital Multifunction Instrument · DMAN-00IM-0795 Rev A · rev. 2020-08. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.