- Home
- Modbus register maps
- Seneca
- T203PM single-phase AC/DC power meter (Modbus RTU)
Power meter · Modbus register map
Seneca T203PM single-phase AC/DC power meter (Modbus RTU) Modbus register map
Updated 17 November 2026
The T203PM is a DIN-rail transducer that measures true-RMS AC or DC voltage and current on one phase and works out power, energy, power factor, frequency and THD. It answers Modbus RTU on RS-485 (and on USB for setup). This map covers the float measurement block, min/max values, scaled integer copies, the 64-bit energy counters, the command register and the analog/digital output setup.
This page lists 61 Modbus registers for the Seneca T203PM single-phase AC/DC power meter (Modbus RTU) — 23 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Seneca’s own free documentation (linked below) and checked against it.
- Manufacturer
- Seneca
- Model
- T203PM single-phase AC/DC power meter (Modbus RTU)
- Equipment type
- Power meter
- Registers
- 61 (23 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- T203PM100-MU, T203PM300-MU, T203PM600-MU, T203PM-MU, T-203PM
Integration notes: Seneca T203PM single-phase AC/DC power meter (Modbus RTU)
Read holding registers 104-125 (function 03) in one block for volts, amps, powers, energies, frequency, PF and THD as ABCD floats. Use the 64-bit counters at 181/185/189 when you need exact energy totals.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 104 | RMS voltage | FLOAT32 ABCD | RMS voltage | Read |
| HR 106 | RMS current | FLOAT32 ABCD | RMS current | Read |
| HR 108 | Active power | FLOAT32 ABCD | Active power | Read |
| HR 114 | Active energy | FLOAT32 ABCD | Active energy | Read |
| HR 120 | Frequency | FLOAT32 ABCD | Frequency | Read |
| HR 122 | Power factor | FLOAT32 ABCD | Power factor | Read |
| HR 181 | Active energy counter | UINT64 ABCD | Active energy counter, Wh/10 | Read/write |
Enable Modbus control & writes
Modbus RTU slave is always on. Slave ID is register 2 and serial format register 81; the maker recommends its Easy Setup 2 software for configuration.
Byte order & addressing
- 0-based offset is the wire address; tables also print 4x numbers.
- Add 1000 to an address for the word-swapped copy of a 32-bit value.
- Energy counters count in tenths of Wh.
Network setup
- Set the slave ID (offset 2) and the stop bit / parity / baud word (offset 81). The command register (offset 4) accepts 49600 (write to flash) and 49568 (reboot); the manual does not say whether a reboot is needed for new serial settings.
- Set AC or DC measuring with offset 82.
Watch out for
- While a USB cable is plugged in, the RS-485 port stops answering; unplug USB to restore it.
- To preset energy counters, first write 49616 to the command register, write the counters, then write 49617.
Seneca T203PM single-phase AC/DC power meter (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 1doc 40002 | Firmware revision | UINT16 | Read | |||||
| HR | 2doc 40003 | Modbus slave ID | Flash register; limit writes to about 10,000. | UINT16 | Read/write | ||||
| HR | 4doc 40005 | Command register | Write a command code; table prints RO but the manual writes commands here. | UINT16 | Read/write | 45505 = Clear energies; 49568 = Reboot; 49600 = Write to flash; 49612 = Clear min/max; 49616 = Enable write custom energies; 49617 = Write custom energies and reboot | |||
| HR | 71doc 40072 | Voltage multiplier | Must be > 0. | FLOAT32 | ABCD | Read/write | |||
| HR | 73doc 40074 | Current multiplier | Must be > 0. | FLOAT32 | ABCD | Read/write | |||
| HR | 75doc 40076 | Voltage transformation ratio | Must be > 0. | FLOAT32 | ABCD | Read/write | |||
| HR | 77doc 40078 | Current cut-off | 0 = disabled. | FLOAT32 | ABCD | A | Read/write | ||
| HR | 79doc 40080 | Voltage cut-off | 0 = disabled. | FLOAT32 | ABCD | V | Read/write | ||
| HR | 81doc 40082 | Serial settings (stop bits / parity / baud) | Bit 12 stop bits, bits 8-9 parity, bits 0-7 baud code. | BITMAP16 | Read/write | bit 12 = Stop bits: 0 = 1, 1 = 2; bit 0-7 = Baud: 0=2400 1=4800 2=9600 3=19200 4=38400 5=57600 6=115200; bit 8-9 = Parity: 0 none, 1 even, 2 odd | |||
| HR | 82doc 40083 | Measure type | UINT16 | Read/write | 0 = AC; 1 = DC | ||||
| HR | 83doc 40084 | AO / DO measure selection | High byte = analog output source, low byte = digital output source. | UINT16 | Read/write | bit 0-7 = DO measure: same codes; bit 8-15 = AO measure: 0 none,1 V,2 A,3 P,4 Q,5 S,6 Hz,7 PF,8 THD | |||
| HR | 84doc 40085 | Digital output behaviour | UINT16 | Read/write | 0 = None; 1 = Max alarm; 2 = Min alarm; 3 = Inside window; 4 = Outside window; 5 = 1000 pulses/kWh; 6 = 100 pulses/kWh; 7 = 10 pulses/kWh; 8 = 1 pulse/kWh; 9 = 100 pulses/MWh; 10 = 10 pulses/MWh; 11 = 1 pulse/MWh | ||||
| HR | 85doc 40086 | AO input scale start | FLOAT32 | ABCD | Read/write | ||||
| HR | 87doc 40088 | AO input scale end | FLOAT32 | ABCD | Read/write | ||||
| HR | 89doc 40090 | AO output voltage minimum | FLOAT32 | ABCD | V | Read/write | |||
| HR | 91doc 40092 | AO output voltage maximum | FLOAT32 | ABCD | V | Read/write | |||
| HR | 93doc 40094 | AO output voltage present | FLOAT32 | ABCD | V | Read | |||
| HR | 95doc 40096 | DO normally high | UINT16 | Read/write | 0 = Normally low; 1 = Normally high | ||||
| HR | 96doc 40097 | DO low alarm threshold | FLOAT32 | ABCD | Read/write | ||||
| HR | 98doc 40099 | DO high alarm threshold | FLOAT32 | ABCD | Read/write | ||||
| HR | 100doc 40101 | DO alarm hysteresis | FLOAT32 | ABCD | Read/write | ||||
| HR | 102doc 40103 | DO alarm delay | Counts of 10 ms. | UINT16 | × 10 | ms | Read/write | ||
| HR | 103doc 40104 | DO alarm status | UINT16 | Read | 0 = None; 1 = Max pre-alarm; 2 = Min pre-alarm; 4 = Inside window pre-alarm; 8 = Outside window pre-alarm; 256 = Max alarm; 512 = Min alarm; 1024 = Inside window alarm; 2048 = Outside window alarm | ||||
| HR | 104doc 40105 | RMS voltage | FLOAT32 | ABCD | V | Read | |||
| HR | 106doc 40107 | RMS current | Signed in DC mode. | FLOAT32 | ABCD | A | Read | ||
| HR | 108doc 40109 | Active power | FLOAT32 | ABCD | W | Read | |||
| HR | 110doc 40111 | Reactive power | FLOAT32 | ABCD | var | Read | |||
| HR | 112doc 40113 | Apparent power | FLOAT32 | ABCD | VA | Read | |||
| HR | 114doc 40115 | Active energy | FLOAT32 | ABCD | Wh | Read | |||
| HR | 116doc 40117 | Reactive energy | FLOAT32 | ABCD | varh | Read | |||
| HR | 118doc 40119 | Apparent energy | FLOAT32 | ABCD | VAh | Read | |||
| HR | 120doc 40121 | Frequency | FLOAT32 | ABCD | Hz | Read | |||
| HR | 122doc 40123 | Power factor | FLOAT32 | ABCD | Read | ||||
| HR | 124doc 40125 | THD | Measured on current. | FLOAT32 | ABCD | % | Read | ||
| HR | 139doc 40140 | Minimum RMS voltage | FLOAT32 | ABCD | V | Read | |||
| HR | 141doc 40142 | Maximum RMS voltage | FLOAT32 | ABCD | V | Read | |||
| HR | 143doc 40144 | Minimum RMS current | FLOAT32 | ABCD | A | Read | |||
| HR | 145doc 40146 | Maximum RMS current | FLOAT32 | ABCD | A | Read | |||
| HR | 147doc 40148 | Minimum active power | FLOAT32 | ABCD | W | Read | |||
| HR | 149doc 40150 | Maximum active power | FLOAT32 | ABCD | W | Read | |||
| HR | 151doc 40152 | Minimum reactive power | FLOAT32 | ABCD | var | Read | |||
| HR | 153doc 40154 | Maximum reactive power | FLOAT32 | ABCD | var | Read | |||
| HR | 155doc 40156 | Minimum apparent power | FLOAT32 | ABCD | VA | Read | |||
| HR | 157doc 40158 | Maximum apparent power | Table text says minimum; register name is the maximum. | FLOAT32 | ABCD | VA | Read | ||
| HR | 159doc 40160 | Minimum frequency | FLOAT32 | ABCD | Hz | Read | |||
| HR | 161doc 40162 | Maximum frequency | FLOAT32 | ABCD | Hz | Read | |||
| HR | 163doc 40164 | Minimum power factor | FLOAT32 | ABCD | Read | ||||
| HR | 165doc 40166 | Maximum power factor | FLOAT32 | ABCD | Read | ||||
| HR | 167doc 40168 | Minimum THD | FLOAT32 | ABCD | % | Read | |||
| HR | 169doc 40170 | Maximum THD | FLOAT32 | ABCD | % | Read | |||
| HR | 173doc 40174 | RMS voltage (integer) | INT16 | × 0.1 | V | Read | |||
| HR | 174doc 40175 | RMS current (integer) | INT16 | × 0.1 | A | Read | |||
| HR | 175doc 40176 | Active power (integer) | INT32 | ABCD | × 0.1 | W | Read | ||
| HR | 177doc 40178 | Reactive power (integer) | INT32 | ABCD | × 0.1 | var | Read | ||
| HR | 179doc 40180 | Apparent power (integer) | INT32 | ABCD | × 0.1 | VA | Read | ||
| HR | 181doc 40182 | Active energy counter | Writable only after the enable-custom-energies command. | UINT64 | ABCD | × 0.1 | Wh | Read/write | |
| HR | 185doc 40186 | Reactive energy counter | Writable only after the enable-custom-energies command. | UINT64 | ABCD | × 0.1 | varh | Read/write | |
| HR | 189doc 40190 | Apparent energy counter | Writable only after the enable-custom-energies command. | UINT64 | ABCD | × 0.1 | VAh | Read/write | |
| HR | 193doc 40194 | Frequency (integer) | UINT16 | × 0.1 | Hz | Read | |||
| HR | 194doc 40195 | Power factor (integer) | INT16 | × 0.001 | Read | ||||
| HR | 195doc 40196 | THD (integer) | INT16 | × 0.1 | % | Read |
Notes on this map
- Only function codes 03, 06 and 16 are supported; every value, including measurements, is a holding register.
- 32-bit values are MSW in the lower register (ABCD) and 64-bit counters are MMSW first (ABCD). The manual says adding 1000 to an address gives the same 32-bit value word-swapped (e.g. current at 41107); that mirror block is not listed here.
- Integer copies are scaled as printed: V/10, A/10, W/10, Hz/10, PF/1000, THD/10; energy counters are Wh/10 (varh/10, VAh/10).
- The table marks the command register (40005) RO, but the manual's procedures write commands to it, so it is listed as RW.
- Registers marked RW* are stored in flash and survive about 10,000 writes.
- Left out: reserved registers and the integer min/max copies (40197-40218); the float min/max block covers the same values.
- The manual does not state factory defaults for address, baud rate or parity.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Seneca T203PM single-phase AC/DC power meter (Modbus RTU)
What Modbus registers does the Seneca T203PM single-phase AC/DC power meter (Modbus RTU) have?
This map lists 61 registers: 61 holding registers. 23 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Seneca T203PM single-phase AC/DC power meter (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The table prints both the 4x number (40002) and the 0-based offset (1). The offset is the wire address: 40002 is sent as 1.
What byte order does the Seneca T203PM single-phase AC/DC power meter (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Seneca T203PM single-phase AC/DC power meter (Modbus RTU)?
Start with HR 104 RMS voltage (RMS voltage); HR 106 RMS current (RMS current); HR 108 Active power (Active power); HR 114 Active energy (Active energy); HR 120 Frequency (Frequency); HR 122 Power factor (Power factor); HR 181 Active energy counter (Active energy counter, Wh/10).
How do I enable Modbus control of the Seneca T203PM single-phase AC/DC power meter (Modbus RTU)?
Modbus RTU slave is always on. Slave ID is register 2 and serial format register 81; the maker recommends its Easy Setup 2 software for configuration.
Where is the official Seneca T203PM single-phase AC/DC power meter (Modbus RTU) Modbus documentation?
The source is T203PM100-MU / T203PM300-MU / T203PM600-MU User Manual (MI00571-3-EN), revision 2023-03-16, published free by Seneca at https://www.seneca.it/media/6849089/mi00571-3-en.pdf.
More Seneca Modbus register maps
- Sensor (remote I/O module, digital inputs/outputs)
Seneca R-16DI-8DO Ethernet I/O (16 digital inputs, 8 digital outputs)
R-16DI-8DO in the Series R I/O manual MI-00604-29-EN.
Also known as: R16DI8DO, R-16DI-8DO, Seneca R series 16DI 8DO - Sensor (remote I/O module, digital inputs/outputs)
Seneca R-32DIDO Ethernet I/O (32 digital inputs/outputs)
R-32DIDO (R-32DIDO-1 / R-32DIDO-2) in the Series R I/O manual MI-00604-29-EN.
Also known as: R32DIDO, R-32DIDO-1, R-32DIDO-2, Seneca R series 32DIDO - Sensor (remote I/O module, analog outputs)
Seneca R-4AO-8DIDO Ethernet I/O (4 analog outputs, 8 digital I/O)
R-4AO-8DIDO in the Series R I/O manual MI-00604-29-EN.
Also known as: R4AO8DIDO, R-4AO-8DIDO, Seneca R series 4AO - Sensor (remote I/O module, RTD inputs)
Seneca R-4RTD-8DIDO Ethernet I/O (4 RTD inputs, 8 digital I/O)
R-4RTD-8DIDO in the Series R I/O manual MI-00604-29-EN.
Also known as: R4RTD8DIDO, R-4RTD-8DIDO, Seneca R series 4RTD - Sensor (load cell / strain gauge converter)
Seneca R-SG3 Ethernet load cell converter
R-SG3 in the Series R I/O manual MI-00604-29-EN.
Also known as: RSG3, R-SG3, Seneca R series strain gauge - Power meter (three-phase network analyzer)
Seneca R203 three-phase power analyzer (Ethernet + RS-485)
R203-1 and R203-2 as covered by user manual MI-00591-4-EN.
Also known as: R203-1, R203-2, Seneca R203 - Sensor (I/O module, 10 digital inputs and counters)
Seneca Z-10-D-IN 10-channel digital input / counter module (HW2)
Seneca Z-10-D-IN hardware 2 with the 32-bit counter firmware, per user manual MI00253-10-EN.
Also known as: Z-10-D-IN, Z-10-D-IN HW2 - Actuator / valve driver (I/O module, 3 analog outputs)
Seneca Z-3AO 3-channel analog output module
Seneca Z-3AO DIN-rail module with three voltage/current outputs and RS-485 Modbus RTU, per user manual MI00260-2-EN.
Also known as: Z-3AO - Sensor (I/O module, 4 analog inputs)
Seneca Z-4AI 4-channel analog input module
Seneca Z-4AI DIN-rail module with 4 voltage/current inputs and RS-485 Modbus RTU, per user manual MI002572-E.
Also known as: Z-4AI - Sensor (RTD temperature input module)
Seneca Z-4RTD2-SI 4-channel RTD input module (Modbus RTU)
Z-4RTD2-SI per user manual MI00584-4-EN.
Also known as: Z-4RTD2, Z4RTD2-SI, Seneca Z-4RTD2-SI - Sensor (I/O module, 4 thermocouple inputs)
Seneca Z-4TC 4-channel thermocouple input module
Seneca Z-4TC DIN-rail module with four thermocouple/mV inputs and RS-485 Modbus RTU, per user manual MI00258-3-EN.
Also known as: Z-4TC - Sensor (I/O module, 8 analog inputs)
Seneca Z-8AI 8-channel analog input module
Seneca Z-8AI DIN-rail module with 8 voltage/current inputs and RS-485 Modbus RTU, per user manual MI00259-3-EN.
Also known as: Z-8AI - Sensor (digital input / counter I/O module)
Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU)
Z-D-IN DIN-rail module, user manual MI00252-3-EN (revision 3, 13/01/2022).
Also known as: ZDIN, Z D IN, Seneca Z-D-IN
Other power & energy meters register maps
- Power meter (power quality)
Siemens SICAM P850 / P855 power monitoring and PQ device
SICAM P850 / P855 (7KG85x) with Modbus TCP or Modbus RTU, firmware V3.11, per communication manual E50417-C1040-C482-B1 (05.2024).
Also known as: 7KG85, 7KG85X, SICAM P850, SICAM P855 - Power meter (branch circuit monitoring)
ABB CMS-700 circuit monitoring system control unit (Modbus RTU / TCP)
ABB CMS-700 control unit with up to 96 CMS branch current sensors, per the CMS-700 user manual (Modbus and SNMP mapping chapter).
Also known as: CMS-700, CMS700, ABB CMS-700, CMS-700 control unit - Power meter (circuit breaker trip unit)
ABB SACE PR122/P, PR123/P, PR332/P, PR333/P trip units with PR120/D-M or PR330/D-M (Modbus RTU)
ABB SACE PR122/P and PR123/P (Emax) and PR332/P and PR333/P (Emax X1, Tmax T7, Tmax T8) protection releases with the Modbus RTU communication module, per 1SDH000556R0001.
Also known as: PR122/P, PR123/P, PR332/P, PR333/P, PR120/D-M, PR330/D-M, Emax PR122, Emax PR123, Tmax T7 PR332, Emax X1 PR333, Tmax T8 PR332 - Energy meter (thermal / BTU meter)
Belimo Thermal Energy Meter (TEM) DN 15-50, Version 4 (Modbus RTU / TCP)
Belimo Thermal Energy Meter DN 15...50 version 4 (22PE..-1U.., 22PF-..U..), interface description V4.2.0 edition 2025-11.
Also known as: 22PE-1U, 22PEM-1UC, 22PE..-1U.., 22PF, Belimo Thermal Energy Meter, Belimo TEM - Energy meter (energy analyzer)
Carlo Gavazzi EM24-DIN (PFA, PFB and X models)
EM24-DIN three-phase energy analyzers, PFA/PFB (MID) and X models with the RS485 Modbus RTU port (IS option), protocol version 4 revision 0.
Also known as: EM24, EM24DIN, EM24DINAV93XISPFA, EM24DINAV93XISPFB, EM24DINAV93XISX, EM24DINAV53XISX, EM24DINAV23XISX, EM24 DIN AV9, EM24 DIN AV5 - Energy meter
Carlo Gavazzi EM530 / EM540 three-phase energy meters (RS485 Modbus)
EM530 (CT-connected) and EM540 (direct-connected) with the S1 RS485 port, X and MID (PFA/PFB/PFC) versions, protocol document version 1.3.
Also known as: EM530, EM540, EM530DINAV53XS1X, EM530DINAV53XS1PFA, EM530DINAV53XS1PFB, EM530DINAV53XS1PFC, EM540DINAV23XS1X, EM540DINAV23XS1PFA, EM540DINAV23XS1PFB, EM540DINAV23XS1PFC, EM500 series
All power & energy meters Modbus register maps →
Source: T203PM100-MU / T203PM300-MU / T203PM600-MU User Manual · MI00571-3-EN · rev. 2023-03-16. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.