- Home
- Modbus register maps
- Seneca
- Z-D-IN 5-channel digital input / counter module (Modbus RTU)
Sensor (digital input / counter I/O module) · Modbus register map
Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) Modbus register map
Updated 17 November 2026
The Z-D-IN is a DIN-rail module with five digital inputs, each feeding a counter, on an RS-485 Modbus RTU port. Address and baud rate come from DIP switches or from EEPROM. This map covers input states, the five counters (IN5 can run as a 32-bit counter), filter, configuration flags and the save/reset command register.
This page lists 16 Modbus registers for the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) — 14 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Seneca’s own free documentation (linked below) and checked against it.
- Manufacturer
- Seneca
- Model
- Z-D-IN 5-channel digital input / counter module (Modbus RTU)
- Equipment type
- Sensor (digital input / counter I/O module)
- Registers
- 16 (14 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 38400 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- CDAB low word first (word-swapped)
- Also known as
- ZDIN, Z D IN, Seneca Z-D-IN
- Source document
- User Manual Z-D-IN · MI00252-3-EN · rev. 2022-01-13
Integration notes: Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU)
Read holding registers 0-6 (function 03) for the input states and the five counters. Write a counter register to preset or clear it.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 1 | Input status and counter overflows | BITMAP16 | Input states and overflow flags | Read/write |
| HR 2 | Counter 1 | UINT16 | Counter 1 | Read/write |
| HR 3 | Counter 2 | UINT16 | Counter 2 | Read/write |
| HR 4 | Counter 3 | UINT16 | Counter 3 | Read/write |
| HR 5 | Counter 4 | UINT16 | Counter 4 | Read/write |
| HR 6 | Counter 5 (16-bit mode) | UINT16 | Counter 5 | Read/write |
Enable Modbus control & writes
Modbus RTU is always on. DIP switches 3-8 set the address (all off = take address and baud from EEPROM), 1-2 the baud rate, 9-10 the RS-485 terminator.
Byte order & addressing
- Offset address is the wire address.
- The 32-bit IN5 counter is LSW first.
Network setup
- Default 38400 8N1, address 1.
- After writing the filter or flags, set bit 0 of register 10 to save to EEPROM.
Watch out for
- Overflow flags in register 1 stay set until written back to 0.
Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 40001 | Machine ID | Module identification code. | UINT16 | Read | ||||
| HR | 1doc 40002 | Input status and counter overflows | Overflow bits can be written to 0 to clear them. | BITMAP16 | Read/write | bit 0 = IN1 state; bit 1 = IN2 state; bit 2 = IN3 state; bit 3 = IN4 state; bit 4 = IN5 state; bit 8 = Counter 1 overflow/underflow; bit 9 = Counter 2 overflow/underflow; bit 10 = Counter 3 overflow/underflow; bit 11 = Counter 4 overflow/underflow; bit 12 = Counter 5 overflow/underflow | |||
| HR | 2doc 40003 | Counter 1 | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 3doc 40004 | Counter 2 | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 4doc 40005 | Counter 3 | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 5doc 40006 | Counter 4 | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 6doc 40007 | Counter 5 (16-bit mode) | 16-bit counter (0-65535) kept in FeRAM; writable. In 32-bit mode use 18-19. | UINT16 | Read/write | ||||
| HR | 7doc 40008 | Input filter | 1-254 ms, applied to all inputs (not IN5 in 32-bit mode). Default 3. | UINT16 | ms | Read/write | |||
| HR | 8doc 40009 | Configuration flags | Saved to EEPROM only after the save command bit. | BITMAP16 | Read/write | bit 0 = Input logic: 0 direct, 1 inverted; bit 1 = Count mode: 0 up, 1 down; bit 2 = RS485 reply pause: 0 none, 1 insert pause; bit 3 = Parity: 0 none, 1 on; bit 4 = Parity type: 0 even, 1 odd; bit 7 = IN5 32-bit mode (filter off, up to 10 kHz) | |||
| HR | 10doc 40011 | Bit command register | BITMAP16 | Read/write | bit 0 = Write 1: save 40008-40010 to EEPROM; bit 1 = Write 1: reset module | ||||
| HR | 12doc 40013 | Firmware revision | UINT16 | Read | |||||
| HR | 14doc 40015 | Counter 1 copy | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 15doc 40016 | Counter 2 copy | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 16doc 40017 | Counter 3 copy | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 17doc 40018 | Counter 4 copy | 16-bit counter (0-65535) kept in FeRAM; writable. | UINT16 | Read/write | ||||
| HR | 18doc 40019 (LSW) / 40020 (MSW) | Counter 5 (32-bit mode) | 32-bit counter used when IN5 32-bit mode is on; LSW first. | UINT32 | CDAB | Read/write |
Notes on this map
- All registers are holding registers; functions 03, 06 and 16 are supported.
- The only 32-bit value, the IN5 32-bit counter, is stored LSW at 40019 and MSW at 40020 (CDAB), as printed in the table.
- Register 40010 holds node address and baud rate together. Its bit description is self-contradictory (it gives bits 0-7 to both the baud code and the node address), so it is left out; set these with the DIP switches or Easy Setup.
- R/W(*) registers (40008-40010) only reach EEPROM after bit 0 of the command register (40011) is set.
- Default serial settings from the manual: 38400 baud, 8 data bits, no parity, 1 stop bit, address 1.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU)
What Modbus registers does the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) have?
This map lists 16 registers: 16 holding registers. 14 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The table prints both the Modbus address (40001 = first register) and the offset address (0). The offset is what goes on the wire.
What byte order does the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) use for 32-bit values?
Multi-register values in this map use CDAB (low word first (word-swapped)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU)?
Start with HR 1 Input status and counter overflows (Input states and overflow flags); HR 2 Counter 1 (Counter 1); HR 3 Counter 2 (Counter 2); HR 4 Counter 3 (Counter 3); HR 5 Counter 4 (Counter 4); HR 6 Counter 5 (16-bit mode) (Counter 5).
How do I enable Modbus control of the Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU)?
Modbus RTU is always on. DIP switches 3-8 set the address (all off = take address and baud from EEPROM), 1-2 the baud rate, 9-10 the RS-485 terminator.
Where is the official Seneca Z-D-IN 5-channel digital input / counter module (Modbus RTU) Modbus documentation?
The source is User Manual Z-D-IN (MI00252-3-EN), revision 2022-01-13, published free by Seneca at https://www.seneca.it/media/2495/mi00252-3-en.pdf.
More Seneca Modbus register maps
- Sensor (remote I/O module, digital inputs/outputs)
Seneca R-16DI-8DO Ethernet I/O (16 digital inputs, 8 digital outputs)
R-16DI-8DO in the Series R I/O manual MI-00604-29-EN.
Also known as: R16DI8DO, R-16DI-8DO, Seneca R series 16DI 8DO - Sensor (remote I/O module, digital inputs/outputs)
Seneca R-32DIDO Ethernet I/O (32 digital inputs/outputs)
R-32DIDO (R-32DIDO-1 / R-32DIDO-2) in the Series R I/O manual MI-00604-29-EN.
Also known as: R32DIDO, R-32DIDO-1, R-32DIDO-2, Seneca R series 32DIDO - Sensor (remote I/O module, analog outputs)
Seneca R-4AO-8DIDO Ethernet I/O (4 analog outputs, 8 digital I/O)
R-4AO-8DIDO in the Series R I/O manual MI-00604-29-EN.
Also known as: R4AO8DIDO, R-4AO-8DIDO, Seneca R series 4AO - Sensor (remote I/O module, RTD inputs)
Seneca R-4RTD-8DIDO Ethernet I/O (4 RTD inputs, 8 digital I/O)
R-4RTD-8DIDO in the Series R I/O manual MI-00604-29-EN.
Also known as: R4RTD8DIDO, R-4RTD-8DIDO, Seneca R series 4RTD - Sensor (load cell / strain gauge converter)
Seneca R-SG3 Ethernet load cell converter
R-SG3 in the Series R I/O manual MI-00604-29-EN.
Also known as: RSG3, R-SG3, Seneca R series strain gauge - Power meter (three-phase network analyzer)
Seneca R203 three-phase power analyzer (Ethernet + RS-485)
R203-1 and R203-2 as covered by user manual MI-00591-4-EN.
Also known as: R203-1, R203-2, Seneca R203 - Power meter
Seneca T203PM single-phase AC/DC power meter (Modbus RTU)
T203PM100-MU / T203PM300-MU / T203PM600-MU per user manual MI00571-3-EN.
Also known as: T203PM100-MU, T203PM300-MU, T203PM600-MU, T203PM-MU, T-203PM - Sensor (I/O module, 10 digital inputs and counters)
Seneca Z-10-D-IN 10-channel digital input / counter module (HW2)
Seneca Z-10-D-IN hardware 2 with the 32-bit counter firmware, per user manual MI00253-10-EN.
Also known as: Z-10-D-IN, Z-10-D-IN HW2 - Actuator / valve driver (I/O module, 3 analog outputs)
Seneca Z-3AO 3-channel analog output module
Seneca Z-3AO DIN-rail module with three voltage/current outputs and RS-485 Modbus RTU, per user manual MI00260-2-EN.
Also known as: Z-3AO - Sensor (I/O module, 4 analog inputs)
Seneca Z-4AI 4-channel analog input module
Seneca Z-4AI DIN-rail module with 4 voltage/current inputs and RS-485 Modbus RTU, per user manual MI002572-E.
Also known as: Z-4AI - Sensor (RTD temperature input module)
Seneca Z-4RTD2-SI 4-channel RTD input module (Modbus RTU)
Z-4RTD2-SI per user manual MI00584-4-EN.
Also known as: Z-4RTD2, Z4RTD2-SI, Seneca Z-4RTD2-SI - Sensor (I/O module, 4 thermocouple inputs)
Seneca Z-4TC 4-channel thermocouple input module
Seneca Z-4TC DIN-rail module with four thermocouple/mV inputs and RS-485 Modbus RTU, per user manual MI00258-3-EN.
Also known as: Z-4TC - Sensor (I/O module, 8 analog inputs)
Seneca Z-8AI 8-channel analog input module
Seneca Z-8AI DIN-rail module with 8 voltage/current inputs and RS-485 Modbus RTU, per user manual MI00259-3-EN.
Also known as: Z-8AI
Other remote i/o modules register maps
- Sensor (remote I/O module)
Unipi Technology Unipi Extension xS53 analog input module
Unipi Extension xS53 RS-485 module per the Unipi Extension xS53 Modbus map v2.0.
Also known as: Unipi Extension xS53, xS53 - Sensor (thermistor input module)
ICP DAS M-7005 8-channel thermistor input module (Modbus RTU)
M-7005 in Modbus RTU mode, per I-7005/M-7005 User Manual Rev B2.4 (7MH-018-B24). The I-7005 uses the DCON protocol and is not covered.
Also known as: M-7005, M7005, I-7005/M-7005 - Sensor (remote I/O module)
Moxa ioLogik R1240 RS-485 remote I/O
ioLogik R1240 per the ioLogik R1200 Series User's Manual, Edition 3.4 (April 2021).
Also known as: ioLogik R1240, R1240, R1240-T - Sensor (thermocouple input module)
Teracom TST320 2-channel thermocouple module with Modbus RTU
TST320 per the Teracom TST320 user manual Revision R1.6.
Also known as: TST320 - Sensor (Ethernet analog input module)
Acromag BusWorks XT1211-000 / XT1221-000 8-channel differential analog input (Modbus TCP)
BusWorks XT1211-000 (current) and XT1221-000 (voltage) per user's manual 8500951K.
Also known as: XT1211-000, XT1221-000, XT1211, XT1221, BusWorks XT1211, BusWorks XT1221 - Sensor / remote digital I/O module
ICP DAS tM series digital I/O modules tM-P4C4, tM-C8, tM-P8 (Modbus RTU)
tM-P4C4 (4 DI + 4 DO), tM-C8 (8 DO) and tM-P8 (8 DI) with the Modbus RTU protocol selected, per the tM Series DIO User Manual Rev A1.4.
Also known as: tM-P4C4, tM-C8, tM-P8
All remote i/o modules Modbus register maps →
Source: User Manual Z-D-IN · MI00252-3-EN · rev. 2022-01-13. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.