- Home
- Modbus register maps
- Rishabh Instruments
- RISH Delta Power NX multifunction power meter
Power meter · Modbus register map
Rishabh Instruments RISH Delta Power NX multifunction power meter Modbus register map
Updated 19 November 2026
The RISH Delta Power NX is a 96 x 96 mm multifunction meter that measures voltage, current, power, power factor, frequency and demand (no energy counters) on 1-phase and 3-phase networks, with an RS-485 Modbus RTU port. Every value is an IEEE 754 float in two registers: measurements are input registers (FC04) from 30001, mirrored as holding registers at 40001+, and setup parameters sit at 46003-46085. This map covers the measured values, demands, run/on hours and the setup block.
This page lists 89 Modbus registers for the Rishabh Instruments RISH Delta Power NX multifunction power meter — 22 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Rishabh Instruments’s own free documentation (linked below) and checked against it.
- Manufacturer
- Rishabh Instruments
- Model
- RISH Delta Power NX multifunction power meter
- Equipment type
- Power meter
- Registers
- 89 (22 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- RISH Delta Power NX, Delta Power NX, RISH Delta Power
Integration notes: Rishabh Instruments RISH Delta Power NX multifunction power meter
Read 30001-30072 (and the demand block 30083-30106) with FC04 and decode each register pair as a big-endian float. Settings are floats at 46003+ written with FC16.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 0 | V1 | FLOAT32 ABCD | Voltage L1 | Read |
| IR 6 | I1 | FLOAT32 ABCD | Current L1 | Read |
| IR 52 | Watt sum | FLOAT32 ABCD | Total active power | Read |
| IR 62 | PF average | FLOAT32 ABCD | Average power factor | Read |
| IR 70 | System frequency | FLOAT32 ABCD | Frequency | Read |
Enable Modbus control & writes
Set the Modbus address (46047, default 1) and Comsetup code (46045, default 8 = 9600 8N1) from the front panel or over Modbus.
Byte order & addressing
- Setup values are floats too: system type 3 reads back as 40 40 00 00.
- Reading or writing half a float returns exception 02.
- If a password is set, write it to 46033 before changing setup registers.
Network setup
- Comsetup (46045) packs baud 4800-57600, parity and stop bits into one code; see the value list.
Watch out for
- Per-phase PF and line-to-line voltages are only valid for the wiring types noted in each description.
Rishabh Instruments RISH Delta Power NX multifunction power meter Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 0doc 30001 | V1 | L1 voltage (L-N on 4-wire, L-L on 3-wire). | FLOAT32 | ABCD | Read | |||
| IR | 2doc 30003 | V2 | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 4doc 30005 | V3 | 3P4W and 3P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 6doc 30007 | I1 | FLOAT32 | ABCD | Read | ||||
| IR | 8doc 30009 | I2 | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 10doc 30011 | I3 | 3P4W and 3P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 12doc 30013 | W1 | Not on 3P3W. | FLOAT32 | ABCD | Read | |||
| IR | 14doc 30015 | W2 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 16doc 30017 | W3 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 18doc 30019 | VA1 | Not on 3P3W. | FLOAT32 | ABCD | Read | |||
| IR | 20doc 30021 | VA2 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 22doc 30023 | VA3 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 24doc 30025 | VAR1 | Not on 3P3W. | FLOAT32 | ABCD | Read | |||
| IR | 26doc 30027 | VAR2 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 28doc 30029 | VAR3 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 30doc 30031 | PF1 | Not on 3P3W. | FLOAT32 | ABCD | Read | |||
| IR | 32doc 30033 | PF2 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 34doc 30035 | PF3 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 36doc 30037 | Angle1 | Not on 3P3W. | FLOAT32 | ABCD | Read | |||
| IR | 38doc 30039 | Angle2 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 40doc 30041 | Angle3 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 42doc 30043 | Volt average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 44doc 30045 | Volt sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 46doc 30047 | Current average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 48doc 30049 | Current sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 50doc 30051 | Watt average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 52doc 30053 | Watt sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 54doc 30055 | VA average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 56doc 30057 | VA sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 58doc 30059 | VAR average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 60doc 30061 | VAR sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 62doc 30063 | PF average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 64doc 30065 | PF sum | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 66doc 30067 | Phase angle average | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 68doc 30069 | Phase angle sum | Not on 1P2W. | FLOAT32 | ABCD | Read | |||
| IR | 70doc 30071 | System frequency | FLOAT32 | ABCD | Read | ||||
| IR | 82doc 30083 | kW import demand | FLOAT32 | ABCD | Read | ||||
| IR | 84doc 30085 | Max kW import demand | FLOAT32 | ABCD | Read | ||||
| IR | 86doc 30087 | kW export demand | FLOAT32 | ABCD | Read | ||||
| IR | 88doc 30089 | Max kW export demand | FLOAT32 | ABCD | Read | ||||
| IR | 98doc 30099 | KVA demand | FLOAT32 | ABCD | Read | ||||
| IR | 100doc 30101 | Max KVA demand | FLOAT32 | ABCD | Read | ||||
| IR | 102doc 30103 | Current demand | FLOAT32 | ABCD | Read | ||||
| IR | 104doc 30105 | Max current demand | FLOAT32 | ABCD | Read | ||||
| IR | 136doc 30137 | System voltage max | FLOAT32 | ABCD | Read | ||||
| IR | 138doc 30139 | System voltage min | FLOAT32 | ABCD | Read | ||||
| IR | 140doc 30141 | System RPM | Generator speed from 46039 poles. | FLOAT32 | ABCD | Read | |||
| IR | 142doc 30143 | Impulse rate | FLOAT32 | ABCD | Read | ||||
| IR | 144doc 30145 | System current max | FLOAT32 | ABCD | Read | ||||
| IR | 146doc 30147 | System current min | FLOAT32 | ABCD | Read | ||||
| IR | 200doc 30201 | V12 | 3P4W and 1P3W only. | FLOAT32 | ABCD | Read | |||
| IR | 202doc 30203 | V23 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 204doc 30205 | V31 | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 224doc 30225 | Neutral current | 3P4W only. | FLOAT32 | ABCD | Read | |||
| IR | 226doc 30227 | Run hour | FLOAT32 | ABCD | Read | ||||
| IR | 228doc 30229 | On hour | FLOAT32 | ABCD | Read | ||||
| IR | 230doc 30231 | Number of interrupts | FLOAT32 | ABCD | Read | ||||
| IR | 262doc 30263 | Relay 1 status | FLOAT32 | ABCD | Read | ||||
| IR | 500doc 30501 | System kW import demand | FLOAT32 | ABCD | Read | ||||
| IR | 502doc 30503 | System kW export demand | FLOAT32 | ABCD | Read | ||||
| IR | 508doc 30509 | System KVA demand | FLOAT32 | ABCD | Read | ||||
| IR | 510doc 30511 | System current demand | FLOAT32 | ABCD | Read | ||||
| IR | 512doc 30513 | System kW import max demand | FLOAT32 | ABCD | Read | ||||
| IR | 514doc 30515 | System kW export max demand | FLOAT32 | ABCD | Read | ||||
| IR | 520doc 30521 | System KVA max demand | FLOAT32 | ABCD | Read | ||||
| IR | 522doc 30523 | System current max demand | FLOAT32 | ABCD | Read | ||||
| HR | 6002doc 46003 | System type | Default 3. | FLOAT32 | ABCD | Read/write | 1 = 1-phase 2-wire; 2 = 3-phase 3-wire; 3 = 3-phase 4-wire; 4 = 1-phase 3-wire | ||
| HR | 6004doc 46005 | PT primary | 100 V to 1200 kV L-L; default 415. | FLOAT32 | ABCD | Read/write | |||
| HR | 6006doc 46007 | CT primary | 1-9999; default 5. | FLOAT32 | ABCD | Read/write | |||
| HR | 6008doc 46009 | PT secondary | 100-500 V L-L; default 415. | FLOAT32 | ABCD | Read/write | |||
| HR | 6010doc 46011 | CT secondary | FLOAT32 | ABCD | Read/write | 1 = 1 A; 5 = 5 A | |||
| HR | 6014doc 46015 | Demand time | Demand period 5-60; default 8. | FLOAT32 | ABCD | Read/write | |||
| HR | 6030doc 46031 | Reset parameters | FLOAT32 | ABCD | Write | 1 = Lo (min); 2 = Hi (max); 3 = Demand; 4 = Run hour; 5 = On hour; 6 = No. of interrupts; 7 = Reset all | |||
| HR | 6032doc 46033 | Password | 0000-9999; reads 0 when locked, 1 when unlocked. | FLOAT32 | ABCD | Read/write | |||
| HR | 6034doc 46035 | Factory reset | Write 5555 to restore factory defaults. | FLOAT32 | ABCD | Write | |||
| HR | 6038doc 46039 | No. of poles | Generator poles for RPM, 2-40 even. | FLOAT32 | ABCD | Read/write | |||
| HR | 6040doc 46041 | Autoscroll | FLOAT32 | ABCD | Read/write | 0 = Off; 1 = On | |||
| HR | 6042doc 46043 | Noise cutoff | FLOAT32 | ABCD | Read/write | 0 = 0 mA; 30 = 30 mA | |||
| HR | 6044doc 46045 | Comsetup (RS485 set-up code) | Default 8 (9600 bps, no parity, 1 stop). | FLOAT32 | ABCD | Read/write | 4 = 4800 bps, no parity, 1 stop; 5 = 4800 bps, no parity, 2 stop; 6 = 4800 bps, even, 1 stop; 7 = 4800 bps, odd, 1 stop; 8 = 9600 bps, no parity, 1 stop; 9 = 9600 bps, no parity, 2 stop; 10 = 9600 bps, even, 1 stop; 11 = 9600 bps, odd, 1 stop; 12 = 19200 bps, no parity, 1 stop; 13 = 19200 bps, no parity, 2 stop; 14 = 19200 bps, even, 1 stop; 15 = 19200 bps, odd, 1 stop; 16 = 38400 bps, no parity, 1 stop; 17 = 38400 bps, no parity, 2 stop; 18 = 38400 bps, even, 1 stop; 19 = 38400 bps, odd, 1 stop; 20 = 57600 bps, no parity, 1 stop; 21 = 57600 bps, no parity, 2 stop; 22 = 57600 bps, even, 1 stop; 23 = 57600 bps, odd, 1 stop | ||
| HR | 6046doc 46047 | Modbus address | 1-247; default 1. | FLOAT32 | ABCD | Read/write | |||
| HR | 6048doc 46049 | Register order / word order | Write 2141.0 in the wanted order to switch normal/reversed float word order. | FLOAT32 | ABCD | Read/write | |||
| HR | 6054doc 46055 | Relay 1 output select | FLOAT32 | ABCD | Read/write | 0 = None; 2 = Limit output | |||
| HR | 6056doc 46057 | Limit 1 parameter select | Parameter number per manual Table 2. | FLOAT32 | ABCD | Read/write | |||
| HR | 6058doc 46059 | Limit 1 configuration | FLOAT32 | ABCD | Read/write | 0 = Hi-alarm, energized relay; 1 = Hi-alarm, de-energized relay; 2 = Lo-alarm, energized relay; 3 = Lo-alarm, de-energized relay | |||
| HR | 6060doc 46061 | Limit 1 trip point | Percent; values per manual Table 2. | FLOAT32 | ABCD | Read/write | |||
| HR | 6062doc 46063 | Limit 1 hysteresis | 0.5-50 %; default 50. | FLOAT32 | ABCD | Read/write | |||
| HR | 6064doc 46065 | Limit 1 on delay | 1-10. | FLOAT32 | ABCD | Read/write | |||
| HR | 6066doc 46067 | Limit 1 off delay | 1-10. | FLOAT32 | ABCD | Read/write | |||
| HR | 6084doc 46085 | Version no. | Firmware version. | FLOAT32 | ABCD | Read |
Notes on this map
- The data-format table states IEEE 754 floats, most significant byte first; the Volts 3 example returns 43 5B 41 21 (219.25 V), so ABCD is the default. 46049 can switch to reversed order.
- Every 3X value can also be read with FC03 at the number plus 10000; only the 3X copies are listed.
- The register table has no unit column, so units are left blank.
- Left out: the min/max history from 31301 and the user-assignable registers. Demand time (46015) is printed as seconds in Table 4 and minutes in the explanation, so no unit is given.
- Up to 40 parameters (80 registers) per read request.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Rishabh Instruments RISH Delta Power NX multifunction power meter
What Modbus registers does the Rishabh Instruments RISH Delta Power NX multifunction power meter have?
This map lists 89 registers: 66 input registers, 23 holding registers. 22 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Rishabh Instruments RISH Delta Power NX multifunction power meter Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The manual prints 3X/4X register numbers. Wire address = number - 30001 (FC04) or - 40001 (FC03/FC16): the Volts 3 example (30005) starts at 00 04 and the system-type example (46003) starts at 17 72 (6002).
What byte order does the Rishabh Instruments RISH Delta Power NX multifunction power meter use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Rishabh Instruments RISH Delta Power NX multifunction power meter?
Start with IR 0 V1 (Voltage L1); IR 6 I1 (Current L1); IR 52 Watt sum (Total active power); IR 62 PF average (Average power factor); IR 70 System frequency (Frequency).
How do I enable Modbus control of the Rishabh Instruments RISH Delta Power NX multifunction power meter?
Set the Modbus address (46047, default 1) and Comsetup code (46045, default 8 = 9600 8N1) from the front panel or over Modbus.
Where is the official Rishabh Instruments RISH Delta Power NX multifunction power meter Modbus documentation?
The source is Operating Manual RISH Delta Power NX (AMAN-00IM-0117 Rev. E), revision 2024-02, published free by Rishabh Instruments at https://rishabh.co.in/uploads/product/rish-delta-power-nx-72/RISH_Delta_POWER_NX__Manual_REV_E.pdf.
More Rishabh Instruments Modbus register maps
- Energy meter (DC)
Rishabh Instruments RISH DC2111 MOD single-channel DC energy meter
Rishabh RISH DC2111 MOD single-channel DC energy meters with RS-485 Modbus, per interface definition DMAN-00IM-1669 Rev. D (08/25).
Also known as: RISH DC2111 MOD, DC2111 - Energy meter
Rishabh Instruments RISH Delta Energy NX multifunction energy meter
Rishabh RISH Delta Energy NX panel energy meters with RS-485 Modbus RTU, per the operating manual on the product page (standard CT version).
Also known as: RISH Delta Energy NX, Delta Energy NX, RISH Delta Energy - Power meter
Rishabh Instruments RISH Delta VAF NX volt/amp/frequency panel meter
Rishabh RISH Delta VAF NX programmable panel meters with RS-485 Modbus RTU, per operating manual AMAN-00IM-0118 Rev. F.
Also known as: RISH Delta VAF NX, Delta VAF NX, RISH Delta VAF - Power meter (demand controller)
Rishabh Instruments RISH DMCi touch-screen demand controller with TOD
Rishabh RISH DMCi 96 x 96 mm touch-screen demand controllers with the optional RS-485 Modbus output, per interface definition DMAN-00IM-0578 Rev. A (09/16).
Also known as: RISH DMCi, DMCi, Rish DMCi demand controller - Energy meter
Rishabh Instruments RISH EC43xx / ER43xx DIN-rail energy meters
Rishabh RISH EC43xx and ER43xx DIN-rail digital energy meters with RS-485 Modbus, per interface definition DMAN-00IM-09xx Rev. F (11/25).
Also known as: EC4311, EC4321, ER4311, ER4321, RISH EC43X1, EC43XX, ER43XX - Energy meter
Rishabh Instruments RISH ED11XX / EC11XX / ER11XX single-phase DIN-rail energy meters
Rishabh RISH ED11XX (direct), EC11XX (CT) and ER11XX (RJ12 CT) single-phase DIN-rail meters in their Modbus (x1) versions, per operating manual DMAN-00IM-1071 Rev. M.
Also known as: RISH ED11X1, RISH EC11X1, RISH ER11X1, ED1111, EC1111, ER1111, RISH ED11XX, RISH EC11XX, RISH ER11XX - Energy meter
Rishabh Instruments RISH ED21XX / EC21XX / ER21XX single-phase energy meters
Rishabh RISH ED21XX (direct), EC21XX (CT) and ER21XX (RJ12 CT) single-phase meters in their Modbus versions, per operating manual DMAN-00IM-1073 Rev. M.
Also known as: RISH ED21X1, RISH EC21X1, RISH ER21X1, RISH ED21XX, RISH EC21XX, RISH ER21XX - Energy meter
Rishabh Instruments RISH EM 1320 / 1330 / 1340 / 2340 programmable energy meters
Rishabh RISH EM 1320/1330/1340 and EM 2320/2330/2340 panel energy meters with RS-485 Modbus, per interface definition DMAN-00IM-0721 Rev. B (06/2020). Rows marked 'only 2340' apply to the dual-source EM 2340.
Also known as: RISH EM 1320, RISH EM 1330, RISH EM 1340, RISH EM 2320, RISH EM 2330, RISH EM 2340, EM2340DS - Energy meter
Rishabh Instruments RISH EM 3490 DS dual-source (utility/generator) energy meter
Rishabh RISH EM 3490 DS dual-source energy meters (separate utility and generator energy) with RS-485 Modbus, per manual Rev G.
Also known as: RISH EM 3490 DS, EM3490DS, EM 3490DS - Energy meter
Rishabh Instruments RISH EM 3490 SS single-phase energy meter
Rishabh RISH EM 3490 SS single-phase energy meters with the optional RS-485 Modbus output, per the 1-phase manual Rev D.
Also known as: RISH EM 3490 SS 1P, EM3490SS 1P, EM 3490 SS single-phase - Energy meter
Rishabh Instruments RISH EM 3490 SS three-phase single-source energy meter
Rishabh RISH EM 3490 SS three-phase energy meters with the optional RS-485 Modbus output, per the 3-phase manual Rev E.
Also known as: RISH EM 3490 SS 3P, EM3490SS 3P, EM 3490 SS three-phase - Energy meter (DC)
Rishabh Instruments RISH EM DC 6000 programmable DC energy meter
Rishabh RISH EM DC 6000 single-channel programmable DC energy meters with RS-485 Modbus, per interface definition DMAN-00IM-0862 Rev. 0 (12/2020).
Also known as: RISH EM DC 6000, EMDC 6000, EM DC6000 - Energy meter (DC)
Rishabh Instruments RISH EM DC 6001 / 6002 multi-channel DC energy meter
Rishabh RISH EM DC 6001 / 6002 multi-channel DC energy meters with RS-485 Modbus, per interface definition 2-60-006-00-00627 Rev. 0 (10/2015).
Also known as: RISH EM DC 6001, RISH EM DC 6002, EM DC 6001, EM DC 6002 - Power meter
Rishabh Instruments RISH LM 1340 multifunction meter
Rishabh RISH LM 1340 panel multifunction instruments with RS-485 Modbus, per interface definition DMAN-00IM-0923 Rev. D (03/2026).
Also known as: RISH LM 1340, LM1340 - Power meter
Rishabh Instruments RISH LM 1360 load manager (LM 13xx)
Rishabh RISH LM 1360 panel meters with RS-485 Modbus, per interface definition DMAN-00IM-0662 Rev. D (01/2024).
Also known as: RISH LM 1360, LM1360, LM 13xx, LM1360 RJ12 - Power meter
Rishabh Instruments RISH LM 1380 multifunction meter
Rishabh RISH LM 1380 panel multifunction instruments with RS-485 Modbus, per interface definition DMAN-00IM-0925 Rev. A (04/2022).
Also known as: RISH LM 1380, LM1380 - Power meter
Rishabh Instruments RISH LM1360+ RJ12 smart energy meter
Rishabh RISH LM1360 PLUS RJ12 smart energy meters (RJ12 CT inputs) with RS-485 Modbus, per interface definition DMAN-00IM-0923 Rev. A (01/2026).
Also known as: RISH LM 1360+, LM1360 PLUS RJ12, LM1360+ - Power meter
Rishabh Instruments RISH Master 3440 (class 0.2S) multifunction meter
Rishabh RISH Master 3440 class 0.2S panel meters with RS-485 Modbus, per interface definition DMAN-00IM-0711 Rev. C (05/2019).
Also known as: RISH Master 3440, RM3440, Master 3440 0.2S - Power meter
Rishabh Instruments RISH Master 3440i / 3440iDL (class 0.2S) touch-screen meter
Rishabh RISH Master 3440i and 3440iDL touch-screen class 0.2S meters with RS-485 Modbus, per interface definition DMAN-00IM-0712 Rev. F (10/2026).
Also known as: RISH Master 3440i, RISH Master 3440iDL, RM3440i, RM3440iDL - Power meter (multi-circuit energy meter)
Rishabh Instruments RISH ML 1400 / ML 1410 Multiload Monitor (Modbus RTU)
RISH Multiload Monitor (12 current channels, 4 voltage channels) per interface definition DMAN-00IM-0795 Rev A (08/2020).
Also known as: RISH ML 1400, RISH ML 1410, RISH MLM, Multiload Monitor - Power meter (power factor controller)
Rishabh Instruments RISH PFC 96 / PFC 144 automatic power factor controller
Rishabh RISH PFC 96 and PFC 144 automatic power factor (APFC) controllers with RS-485 Modbus RTU, per interface definition version D (12/18).
Also known as: RISH PFC 96, RISH PFC 144, PFC96, PFC144, RISH PFC-12, APFC
Other power & energy meters register maps
- Power meter (multi-circuit branch feeder monitor)
SATEC BFM-II branch feeder monitor
SATEC BFM-II multi-circuit meter per Modbus reference guide BG0589 Rev. A12 (May 2024); per-submeter 32-bit measurement registers plus shared setup.
Also known as: BFM II, BFM2, SATEC BFM-II - Energy meter (pulse and status concentrator)
Schneider Electric Acti 9 Smartlink Modbus (A9XMSB11) 11-channel I/O and pulse concentrator
Acti 9 Smartlink Modbus RS-485 module A9XMSB11, per user manual DOCA0004EN-06 (04/2016).
Also known as: Acti 9 Smartlink, Smartlink Modbus, A9XMSB11, Acti9 Smartlink - Energy meter
Siemens SENTRON PAC2200
SENTRON 7KM PAC2200 Modbus TCP and Modbus RTU variants (5 A and 65 A), per Equipment Manual 12/2022.
Also known as: 7KM PAC2200 - Energy meter (Ethernet energy monitoring / data logger)
Teracom TCW260 Ethernet energy monitoring module
TCW260 per the Teracom TCW260 user manual Revision R1.19, firmware V3.009 or later.
Also known as: TCW260 - Energy meter
ABB EQ meter B21 (Modbus RTU)
ABB EQ B21 single-phase 65 A DIN meter with the RS485 interface set to Modbus.
Also known as: B21, EQ B21 - Power meter
Accuenergy Acuvim II Series
Accuenergy Acuvim II series multifunction power meters (manual 1040E1303, V3.2.16 revised September 2026).
Also known as: Acuvim IIR, Acuvim IIW
All power & energy meters Modbus register maps →
Source: Operating Manual RISH Delta Power NX · AMAN-00IM-0117 Rev. E · rev. 2024-02. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.