- Home
- Modbus register maps
- Daikin
- EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)
Heat pump (air-to-water) Modbus interface · Modbus register map
Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) Modbus register map
Updated 19 November 2026
The Daikin HomeHub (EKRHH) connects to a Daikin Altherma system and offers a Modbus TCP (port 502, or 802 with TLS) or Modbus RTU slave. Holding registers set leaving-water and room setpoints, operation mode, on/off, quiet mode, hot-water reheat and booster, weather-dependent mode and the smart-grid mode with power limits; input registers return error state and code, pump/compressor/heater/defrost states, water, outdoor and refrigerant temperatures, flow, power use and setpoint limits. For air-to-air units only the smart-grid mode and demand-control power limit are offered.
This page lists 61 Modbus registers for the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) — 25 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Daikin’s own free documentation (linked below) and checked against it.
- Manufacturer
- Daikin
- Model
- EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)
- Equipment type
- Heat pump (air-to-water) Modbus interface
- Registers
- 61 (25 writable)
- Transport
- Modbus RTU, Modbus TCP
- Default unit ID
- Not stated
- Default serial
- 9600 baud, 8N1
- TCP port
- 502
- Documented addressing
- 1-based (subtract 1 for the wire address)
- Also known as
- EKRHH, Daikin HomeHub, 4P744838-1E, Daikin Altherma 3 Modbus, Altherma Smart Grid Modbus
Integration notes: Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)
Enable Modbus in the ONECTA app, then read input registers 21-53 for state and temperatures and write holding registers 1-13 and 53-58 for setpoints, modes and smart-grid control. Refresh written values periodically because the HomeHub only forwards changes.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 3 | Space heating/cooling ON/OFF | INT16 | Space heating/cooling on/off | Read/write |
| HR 2 | Operation mode | INT16 | Operation mode | Read/write |
| HR 0 | Leaving water Main Heating setpoint | INT16 | Leaving water heating setpoint | Read/write |
| HR 55 | Smart Grid operation mode | INT16 | Smart grid mode | Read/write |
| HR 57 | General power limit | INT16 | General power limit | Read/write |
| IR 20 | Unit abnormality | INT16 | Unit abnormality | Read |
| IR 21 | Unit abnormality code | STRING[2] | Error code | Read |
| IR 30 | Compressor run | INT16 | Compressor running | Read |
| IR 43 | Outside air temperature | INT16 | Outside air temperature | Read |
| IR 50 | Heat pump power consumption | INT16 | Power consumption | Read |
Enable Modbus control & writes
Modbus (RTU or TCP/IP) is configured in the ONECTA app settings for the HomeHub (installer reference guide section 13.1.1).
Byte order & addressing
- Modbus writes are change based: the HomeHub only updates the unit when it sees a change, so values lost during an outage are not resent. Refresh the state from the client periodically.
- After the compressor starts, power-limit writes can be overruled for 15 minutes with max(4.5 kW, register value).
- The error code (input 22) is two ASCII characters packed high byte first.
Network setup
- RTU: 3-wire RS-485 on the HomeHub's X8A connector, 9600 baud, no parity, 8 data bits, 1 stop bit, slave address 1-247.
- TCP: port 502 without encryption or 802 with TLS, at the HomeHub's IP address.
Watch out for
- Room buffering during smart-grid requests needs unit control method [C-07]=2 (room thermostat control); tank buffering needs field settings [E-05]=1 and [E-06]=1.
- The DHW reheat setpoint only takes effect when the tank is enabled, heat pump mode is reheat only and the setpoint mode is fixed.
Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 20doc 21 | Unit abnormality | INT16 | Read | 0 = No error; 1 = Fault; 2 = Warning | ||||
| IR | 21doc 22 | Unit abnormality code | Two ASCII characters, high byte first (e.g. 0x5538 = 'U8'). | STRING[2] | Read | ||||
| IR | 22doc 23 | Unit abnormality sub code | 0-99 on a unit error; 32766 if no error. | INT16 | Read | ||||
| IR | 29doc 30 | Circulation pump running | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 30doc 31 | Compressor run | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 31doc 32 | Booster heater run | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 32doc 33 | Disinfection operation | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 34doc 35 | Defrost | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 35doc 36 | Hot Start | INT16 | Read | 0 = Off; 1 = On | ||||
| IR | 36doc 37 | 3-way valve | INT16 | Read | 0 = Space heating; 1 = DHW | ||||
| IR | 37doc 38 | Operation mode | INT16 | Read | 1 = Heating; 2 = Cooling | ||||
| IR | 39doc 40 | Leaving water temperature PHE | After the plate heat exchanger. | INT16 | × 0.01 | °C | Read | ||
| IR | 40doc 41 | Leaving water temperature BUH | After the backup heater. | INT16 | × 0.01 | °C | Read | ||
| IR | 41doc 42 | Return water temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 42doc 43 | Domestic Hot Water temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 43doc 44 | Outside air temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 44doc 45 | Liquid refrigerant temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 48doc 49 | Flow rate | Litres per minute x 100. | INT16 | × 0.01 | L/min | Read | ||
| IR | 49doc 50 | Remote controller room temperature Main | INT16 | × 0.01 | °C | Read | |||
| IR | 50doc 51 | Heat pump power consumption | Pow16: kW x 100. | INT16 | × 0.01 | kW | Read | ||
| IR | 51doc 52 | DHW normal operation | INT16 | Read | 0 = Idle/buffering; 1 = Operating | ||||
| IR | 52doc 53 | Space heating/cooling normal operation | INT16 | Read | 0 = Idle/buffering; 1 = Operating | ||||
| IR | 53doc 54 | Leaving water Main Heating setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 54doc 55 | Leaving water Main Heating setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| IR | 55doc 56 | Leaving water Main Cooling setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 56doc 57 | Leaving water Main Cooling setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| IR | 57doc 58 | Leaving water Add Heating setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 58doc 59 | Leaving water Add Heating setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| IR | 59doc 60 | Leaving water Add Cooling setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 60doc 61 | Leaving water Add Cooling setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| IR | 75doc 76 | Domestic Hot Water Upper temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 76doc 77 | Domestic Hot Water Lower temperature | INT16 | × 0.01 | °C | Read | |||
| IR | 83doc 84 | Room Heating setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 84doc 85 | Room Heating setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| IR | 85doc 86 | Room Cooling setpoint Lower limit | INT16 | × 0.01 | °C | Read | |||
| IR | 86doc 87 | Room Cooling setpoint Upper limit | INT16 | × 0.01 | °C | Read | |||
| HR | 0doc 1 | Leaving water Main Heating setpoint | Range set by field settings. | INT16 | °C | Read/write | |||
| HR | 1doc 2 | Leaving water Main Cooling setpoint | Range set by field settings. | INT16 | °C | Read/write | |||
| HR | 2doc 3 | Operation mode | Reads 32766 on heating-only units. | INT16 | Read/write | 0 = Auto; 1 = Heating; 2 = Cooling | |||
| HR | 3doc 4 | Space heating/cooling ON/OFF | INT16 | Read/write | 0 = Off; 1 = On | ||||
| HR | 5doc 6 | Room thermostat control Heating setpoint Main | 12-30 °C. | INT16 | °C | Read/write | |||
| HR | 6doc 7 | Room thermostat control Cooling setpoint Main | 15-35 °C. | INT16 | °C | Read/write | |||
| HR | 8doc 9 | Quiet mode operation | INT16 | Read/write | 0 = Off; 1 = On | ||||
| HR | 9doc 10 | DHW reheat setpoint | 30-60 °C; applied only with tank on, reheat-only mode and fixed setpoint. | INT16 | °C | Read/write | |||
| HR | 11doc 12 | DHW reheat ON/OFF | INT16 | Read/write | 0 = Off; 1 = On | ||||
| HR | 12doc 13 | DHW booster mode ON/OFF (Powerful) | INT16 | Read/write | 0 = Off; 1 = On | ||||
| HR | 52doc 53 | Weather dependent mode Main | INT16 | Read/write | 0 = Fixed; 1 = Weather dependent; 2 = Fixed + scheduled; 3 = Weather dependent + scheduled | ||||
| HR | 53doc 54 | Weather dependent mode Main LWT Heating setpoint offset | -10 to 10 °C. | INT16 | °C | Read/write | |||
| HR | 54doc 55 | Weather dependent mode Main LWT Cooling setpoint offset | -10 to 10 °C. | INT16 | °C | Read/write | |||
| HR | 55doc 56 | Smart Grid operation mode | INT16 | Read/write | 0 = Free running; 1 = Forced off; 2 = Recommended on; 3 = Forced on | ||||
| HR | 56doc 57 | Power limit during Recommended on / buffering | Pow16: kW x 100, 0-20 kW. | INT16 | × 0.01 | kW | Read/write | ||
| HR | 57doc 58 | General power limit | Pow16: kW x 100, 0-20 kW. | INT16 | × 0.01 | kW | Read/write | ||
| HR | 58doc 59 | Thermostat Main Input A | Valid only with [C-05]=0 when [C-07]=1; not on Micon ID 20002203 units. | INT16 | Read/write | 0 = Off; 1 = On | |||
| HR | 60doc 61 | Thermostat Add Input A | Valid only with [C-05]=0 when [C-07]=1; not on Micon ID 20002203 units. | INT16 | Read/write | 0 = Off; 1 = On | |||
| HR | 62doc 63 | Leaving water Add Heating setpoint | Range set by field settings. | INT16 | °C | Read/write | |||
| HR | 63doc 64 | Leaving water Add Cooling setpoint | Range set by field settings. | INT16 | °C | Read/write | |||
| HR | 64doc 65 | Weather dependent mode Add | INT16 | Read/write | 0 = Fixed; 1 = Weather dependent; 2 = Fixed + scheduled; 3 = Weather dependent + scheduled | ||||
| HR | 65doc 66 | Weather dependent mode Add LWT Heating setpoint offset | -10 to 10 °C. | INT16 | °C | Read/write | |||
| HR | 66doc 67 | Weather dependent mode Add LWT Cooling setpoint offset | -10 to 10 °C. | INT16 | °C | Read/write | |||
| HR | 1000doc 1001 | Smart Grid operation mode (air-to-air use case) | Use case 4 only; type not printed, same codes as offset 56. | INT16 | Read/write | 0 = Free running; 1 = Forced off; 2 = Recommended on; 3 = Forced on | |||
| HR | 1001doc 1002 | Power limit for Demand Control (air-to-air use case) | Use case 4 only. Pow16: kW x 100, 0-20 kW. | INT16 | × 0.01 | kW | Read/write |
Notes on this map
- Data types are Daikin's: Temp16 and Pow16 are signed 16-bit values divided by 100 (°C and kW); Int16 is a signed 16-bit value with no scaling; Text16 is two ASCII characters. The holding-register setpoints are printed as Int16, so they are whole degrees.
- Holding offsets 59 and 61 (thermostat inputs): with external room thermostat control ([C-07]=1) they are only valid when thermostat type [C-05]=0 (SW contact), otherwise they read 0 (off). Not available on Daikin Altherma 3 R / 3 M units with Micon ID 20002203.
- Offsets 1001 and 1002 belong to use case 4 (air-to-air heat pumps) and are the only registers supported there. The type of 1001 is not printed; it is listed as INT16 with the same codes as offset 56.
- Special return values: 32767 = register unsupported, 32766 = register unavailable in this configuration, 32765 = value not loaded yet (also returned while the HomeHub synchronises).
- Writes to setpoint registers outside the configured range are clamped to the nearest limit; out-of-range writes to other registers are ignored.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)
What Modbus registers does the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) have?
This map lists 61 registers: 36 input registers, 25 holding registers. 25 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The guide lists register offsets 1-based and says PDU addressing is 0-based: register 1 is requested at PDU address 0. Every wire address here is the printed offset minus one.
What are the minimum Modbus registers to integrate the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)?
Start with HR 3 Space heating/cooling ON/OFF (Space heating/cooling on/off); HR 2 Operation mode (Operation mode); HR 0 Leaving water Main Heating setpoint (Leaving water heating setpoint); HR 55 Smart Grid operation mode (Smart grid mode); HR 57 General power limit (General power limit); IR 20 Unit abnormality (Unit abnormality); IR 21 Unit abnormality code (Error code); IR 30 Compressor run (Compressor running); IR 43 Outside air temperature (Outside air temperature); IR 50 Heat pump power consumption (Power consumption).
How do I enable Modbus control of the Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps)?
Modbus (RTU or TCP/IP) is configured in the ONECTA app settings for the HomeHub (installer reference guide section 13.1.1).
Where is the official Daikin EKRHH Daikin HomeHub (Modbus TCP/RTU for Daikin Altherma and air-to-air heat pumps) Modbus documentation?
The source is Installer reference guide - Daikin HomeHub EKRHH (4P744838-1E), revision 2026-01, published free by Daikin at https://www.daikin.eu/content/dam/document-library/Installer-reference-guide/heat/accessories/ekrhh/EKRHH_Installer%20reference%20guide_4PEN744838-1E_English.pdf.
More Daikin Modbus register maps
- Heat pump
Daikin DCOM-LT/MB Modbus interface for Daikin Altherma LT heat pumps
Daikin Altherma low-temperature (LT) air-to-water heat pumps fitted with the DCOM-LT/MB (model number 534-001) P1P2-to-Modbus RTU interface, standard operating mode, per reference manual 534-252-A3.
Also known as: DCOM-LT-MB, 534-001, Altherma LT Modbus interface - VRF / split AC gateway
Daikin DTA116A51 D-NET / Modbus communication adaptor (VRV)
DTA116A51 adaptor with up to 16 VRV indoor units (D-NET 1-00 to 1-15), per functional specification CB13A033 first edition.
Also known as: DTA116A51, DIII-NET Modbus adaptor, D3NET Modbus adapter - VRF / split AC gateway
Daikin EKMBDXB Modbus Interface DIII
EKMBDXB7V1 Modbus RTU interface on the DIII-net of Daikin VRV, Sky Air, split (via KRP928), VAM/VKM ventilation, VRV hydrobox, air curtains, ERQ control box, heating and applied units; design guide 4P642495-1A (2022.02).
Also known as: EKMBDXB7V1, Modbus Interface DIII - VRF / split AC gateway
Daikin EKMBPP1 / EKMBPP1A Modbus adapter (Sky Air / VRV P1P2)
EKMBPP1 and EKMBPP1A adapters on the P1P2 bus of Sky Air / VRV indoor units (up to 16), installation manual 4P720139-1C (2024.11).
Also known as: EKMBPP1, EKMBPP1A
Other pumps register maps
- Pump (booster system / multi-pump controller)
Grundfos Booster systems (Hydro MPC, Hydro Multi-E, Multi-B) via CIM 200 / CIM 500
Grundfos booster systems: Hydro MPC / Control MPC (CU 352), GENIECON MPC, Hydro Multi-B (CU 323), DDD (CU 354), Hydro Multi-E, TPED and MAGNA3-D twin pumps, with CIM/CIU 200, CIM/CIU 500 or SoftCIM.
Also known as: Hydro MPC, Control MPC, CU 352, GENIECON MPC, Hydro Multi-E, Hydro Multi-B, CU 323, DDD, CU 354, TPED, MAGNA3-D, CIM 200, CIM 500, SoftCIM Modbus TCP - Pump (diesel fire pump controller)
Lovato Electric FFL700DP / FFL800DP diesel engine fire pump controllers
FFL700DP and FFL800DP diesel engine fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800DP), per protocol document I557 GB I 11 17.
Also known as: FFL700DP, FFL800DP, FFL 700 DP, FFL 800 DP - Heat pump
Novelan Novelan heat pump controller via Novelan GLT (Modbus TCP)
Novelan (ait-deutschland) heat pumps whose heating and heat pump controller runs software V1.74 / V2.74 / V3.76 / V4.76 or later, with the GLT function licensed via the Novelan GLT USB dongle; operating manual 83055703hDE.
Also known as: Novelan GLT, 83055703, ait-deutschland GLT - Pump (high-efficiency circulator)
Wilo Atmos MAXO with CIF module Modbus RTU
Wilo Atmos MAXO pumps fitted with the plug-in CIF module Modbus RTU (module firmware 1.00-99.99); registers needing a newer module are marked.
Also known as: Wilo-Atmos MAXO - Pump (high-efficiency circulator)
Wilo Stratos PICO plus with CIF module Modbus RTU
Wilo Stratos PICO plus pumps fitted with the plug-in CIF module Modbus RTU (module firmware 1.00-99.99); registers needing a newer module are marked.
Also known as: Wilo-Stratos PICO plus - Heat pump
CTC CTC heat pumps and controllers via BMS (Modbus TCP)
CTC EcoHeat 400, EcoZenith i250/i350/i550, EcoVent i350F, GSi/GS, EcoPart 6xx M/Pro and EcoLogic controllers whose display has three ports (Ethernet), BMS document 16260016-3 (CR01143, 2026-02-02).
Also known as: CTC EcoHeat 400, CTC EcoZenith i250, CTC GSi, CTC GS, CTC EcoZenith i350, CTC EcoVent i350F, CTC EcoZenith i550, CTC EcoPart 600M, CTC EcoPart Pro, CTC EcoLogic, CTC EcoLogic S, 16260016-3
All pumps Modbus register maps →
Source: Installer reference guide - Daikin HomeHub EKRHH · 4P744838-1E · rev. 2026-01. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.