- Home
- Modbus register maps
- Lenze
- SCF Series drive with Modbus module (basic network control)
Variable frequency drive · Modbus register map
Lenze SCF Series drive with Modbus module (basic network control) Modbus register map
Updated 17 November 2026
The SCF is a Lenze AC Tech drive. With its Modbus option it can be started, stopped, reversed and speed-controlled over Modbus RTU at 9600 baud. This map holds the basic control registers from Lenze's quick-start note plus the rule that maps every SCF parameter to a Modbus register.
This page lists 6 Modbus registers for the Lenze SCF Series drive with Modbus module (basic network control) — 4 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Lenze’s own free documentation (linked below) and checked against it.
- Manufacturer
- Lenze
- Model
- SCF Series drive with Modbus module (basic network control)
- Equipment type
- Variable frequency drive
- Registers
- 6 (4 writable)
- Transport
- Modbus RTU
- Default unit ID
- Not stated
- Default serial
- 9600 baud
- Documented addressing
- Modicon 3xxxx/4xxxx (drop the prefix, subtract 1)
- Also known as
- SCF, Lenze AC Tech SCF, AN0028
Integration notes: Lenze SCF Series drive with Modbus module (basic network control)
Set P14 = 01 and P43 = address, write 0 (or the password) to 40049 once after power-up, then write 0008h to 40002 to start and the speed in 0.1 Hz to 40041 (with P05 = 01). Read 40027 for the run status.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 48 | Unlock (AC Tech register 48) | UINT16 | Unlock | Write |
| HR 1 | Drive control (AC Tech register 1) | BITMAP16 | Start / stop / direction | Write |
| HR 40 | Keypad speed command (AC Tech register 40) | UINT16 | Speed command | Read/write |
| HR 26 | Run status (AC Tech register 26, low byte) | UINT16 | Run status | Read |
Enable Modbus control & writes
P14 = 01 enables serial communication; P43 sets the address (1-247); P15 sets data format and watchdog.
Communication loss & watchdog
Fixed 10 s: if enabled via P15 and the master stops communicating while the drive is under network control, the drive stops.
Byte order & addressing
- Use FC06, or FC16 with a length of 1, for every write.
- The local STOP circuit stays active: input 1 (TB1 to TB2) must be asserted to start.
Network setup
- Master at 9600 baud with the data format matching P15.
Watch out for
- Lenze advises not to leave the slave at address 1 to avoid duplicates.
Lenze SCF Series drive with Modbus module (basic network control) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 1doc 40002 | Drive control (AC Tech register 1) | One command per write: 0004h stop, 0008h start, 0040h reverse, 0080h forward, 0200h manual. | BITMAP16 | Write | bit 2 = Stop (per P04); bit 3 = Start; bit 6 = Set reverse (needs P17 = 2); bit 7 = Set forward; bit 9 = Manual mode (use keypad speed register) | |||
| HR | 24doc 40025 | Status block start (AC Tech register 24) | First of a 6-register status block; read 6 registers from here. | UINT16 | Read | ||||
| HR | 26doc 40027 | Run status (AC Tech register 26, low byte) | Low byte = operational status code; see values. | UINT16 | Read | 0 = Fault lockout; 1 = Fault; 2 = Start pending; 3 = Stop; 4 = DC brake; 5 = Run at 0 Hz; 6 = Run; 7 = Accel; 8 = Decel; 9 = Current limit; 10 = Decel override; 11 = Lower transistors switching on | |||
| HR | 40doc 40041 | Keypad speed command (AC Tech register 40) | Network speed when P05 = 01 (keypad); 412 = 41.2 Hz. | UINT16 | × 0.1 | Hz | Read/write | ||
| HR | 48doc 40049 | Unlock (AC Tech register 48) | 0 unlocks control only; password (default 225) also unlocks parameters. | UINT16 | Write | ||||
| HR | 69doc 40070 | P19 acceleration time | Example of the parameter rule: register = parameter + 51. | UINT16 | × 0.1 | s | Read/write |
Notes on this map
- Host: copy hosted by Precision Electric (a Lenze AC Tech distributor); no current copy was found on lenze.com.
- This is a quick-start map only. The full register list is in the SCF ModBus Reference Guide RG-SFMOD, which was not available; other parameters follow 'Modbus register = parameter + 51' with scaling from the SCF manual.
- Only 9600 baud is supported. Data format is chosen with P15: 02/03 = 8N2, 04/05 = 8E1, 06/07 = 8O1 (even numbers enable the 10 s watchdog).
- Only one command bit per write to the control register.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Lenze SCF Series drive with Modbus module (basic network control)
What Modbus registers does the Lenze SCF Series drive with Modbus module (basic network control) have?
This map lists 6 registers: 6 holding registers. 4 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Lenze SCF Series drive with Modbus module (basic network control) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers Modicon 3xxxx/4xxxx (drop the prefix, subtract 1). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The note gives 4xxxx Modbus register numbers, which are AC Tech register + 1 (control register 1 = 40002). Wire address = Modbus register - 40001, so the control register is address 1. SCF parameter Pn is Modbus register n + 51 (P19 -> 40070).
What are the minimum Modbus registers to integrate the Lenze SCF Series drive with Modbus module (basic network control)?
Start with HR 48 Unlock (AC Tech register 48) (Unlock); HR 1 Drive control (AC Tech register 1) (Start / stop / direction); HR 40 Keypad speed command (AC Tech register 40) (Speed command); HR 26 Run status (AC Tech register 26, low byte) (Run status).
How do I enable Modbus control of the Lenze SCF Series drive with Modbus module (basic network control)?
P14 = 01 enables serial communication; P43 sets the address (1-247); P15 sets data format and watchdog.
What happens when the Lenze SCF Series drive with Modbus module (basic network control) loses Modbus communication?
Fixed 10 s: if enabled via P15 and the master stops communicating while the drive is under network control, the drive stops.
Where is the official Lenze SCF Series drive with Modbus module (basic network control) Modbus documentation?
The source is Application Note: Basic Network Control of the SCF Drive using ModBus Communications (AN0028/A1), revision 2008-01. Lenze doesn't publish it on its own website, so this map was re-typed from a free copy at https://www.precision-elec.com/wp-content/uploads/2014/08/basic-network-control-of-scf-drive-using-modbus-communications.pdf. It may be an older revision, so check it against the live unit.
More Lenze Modbus register maps
- Variable frequency drive
Lenze i510 cabinet inverter 0.25-2.2 kW (Modbus RTU)
Lenze i510 cabinet inverters 0.25-2.2 kW with the Modbus/CANopen control unit, selector set to Modbus, firmware 01.01.01.00 as documented in the commissioning manual.
Also known as: i500 series, i510 Cabinet, I51AE - Variable frequency drive
Lenze MC Series drives MC1000 / MC3000 (Modbus RTU)
Lenze AC Tech MC1000 and MC3000 Series drives, software 213-083 rev 13 (parameter configurations 188-190); reference guide RG-MCMOD.
Also known as: MC1000, MC3000, MC Series, Lenze AC Tech MC, RG-MCMOD - Variable frequency drive
Lenze MCH Series HVAC drive (Modbus RTU)
Lenze AC Tech MCH Series drives, software 213-070 rev 00 (parameter configuration 148); reference guide RG-MHMOD.
Also known as: MCH, Lenze AC Tech MCH, RG-MHMOD - Variable frequency drive
Lenze SMVector drive with ESVZAR0 RS-485 Modbus module
Lenze AC Tech SMVector drives up to 10 HP with the ESVZAR0 RS-485 Modbus module, module software 1.01 / 1.10 / 1.30 (guide CMVMB401C).
Also known as: SMVector, SMV, ESVZAR0, Lenze AC Tech SMV, CMVMB401C
Other variable frequency drives register maps
- Variable frequency drive
Mitsubishi Electric FR-E700 compact inverter (PU connector, Modbus RTU)
FR-E700 series (FR-E720/E740/E720S/E710W, incl. SC safety-stop models) using the PU connector with Pr.549 = 1; Instruction Manual (Applied) revision G.
Also known as: FR-E720, FR-E740, FR-E720S, FR-E710W, FR-E700-SC - Variable frequency drive
Schneider Electric Altivar Process ATV900 (ATV930/ATV950, embedded Modbus serial / Modbus TCP)
Altivar Process ATV900 drives (ATV930, ATV950) on the built-in Modbus serial port and the embedded Ethernet port (Modbus TCP). Per Communication Parameters file NHA80944 V4.6.
Also known as: ATV900, ATV930, ATV950, Altivar Process 900, Altivar 930, Altivar 950, ATV930U, ATV930D, ATV950U - Air handler (rotary heat exchanger drive controller)
Swegon SILVER C / SILVER RX rotary heat exchanger controller (Modbus RTU)
The rotary heat exchanger (rotor) drive controller in Swegon SILVER C RX air handling units, per sheet SILVERCModbusHX.201115.
Also known as: SILVER RX heat exchanger controller, SILVER C RX rotor drive, DRHX, SILVERCModbusHX - Variable frequency drive
Toshiba TOSVERT VF-AS3 inverter (RS485 Modbus RTU)
Toshiba TOSVERT VF-AS3 inverters on RS485 port 1 or 2 with the protocol set to MODBUS (F807/F827 = 1); RS485 Communication Function Instruction Manual E6582143.
Also known as: VF-AS3, TOSVERT VF-AS3 - Variable frequency drive
Yaskawa F7 drive (CIMR-F7U, legacy) - Modbus RTU
Yaskawa F7 (CIMR-F7U) general-purpose drives using the built-in RS-422/485 terminals R+/R-/S+/S-, per user manual TM.F7.01 Appendix D, with parameter and monitor addresses from TM.F7.11.
Also known as: CIMR-F7U, F7U, F7 Drive - Variable frequency drive
Yaskawa HV600 HVAC fan and pump drive (MEMOBUS/Modbus RTU)
Yaskawa HV600 drives using the built-in RS-485 port with H5-08 = 0 (MEMOBUS/Modbus), per technical reference SIEPC71061732 revision F.
Also known as: CIPR-HV60, HV600 HVAC drive
All variable frequency drives Modbus register maps →
Source: Application Note: Basic Network Control of the SCF Drive using ModBus Communications · AN0028/A1 · rev. 2008-01 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.