- Home
- Modbus register maps
- Teledyne Detcon
- Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)
Sensor (fixed gas detector) · Modbus register map
Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) Modbus register map
Updated 17 November 2026
The FP-624D is a Detcon catalytic-bead combustible gas sensor with a display, three relays, a 4-20 mA loop and a Modbus RTU RS-485 port. Its holding registers follow the Detcon 700-series layout: range, gas reading in %LEL, span level, sensor life, fault bits, loop current, supply voltage, calibration command, gas/units text and firmware version.
This page lists 13 Modbus registers for the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) — 2 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Teledyne Detcon’s own free documentation (linked below) and checked against it.
- Manufacturer
- Teledyne Detcon
- Model
- Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)
- Equipment type
- Sensor (fixed gas detector)
- Registers
- 13 (2 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- 0-based (the number printed is the address on the wire)
- Also known as
- FP-624D, MicroSafe FP-624D, Detcon FP-624D
Integration notes: Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)
Set the serial ID with the magnet menu, wire RS-485 at 9600 8N1 and poll holding registers 0-9 with function 03.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 2 | Gas concentration | UINT16 | Gas concentration | Read |
| HR 5 | Fault status bits | BITMAP16 | Fault bits | Read |
| HR 1 | Detectable range | UINT16 | Full scale | Read |
| HR 4 | Sensor life | UINT16 | Sensor life | Read |
| HR 8 | 4-20 mA output | UINT16 | Loop current | Read |
Enable Modbus control & writes
The manual describes no separate enable step; set a unique serial ID in the sensor menu (Set Serial ID).
Byte order & addressing
- 40000 = wire address 0.
- The CAL LED flashes each time the sensor answers a poll.
Network setup
- 9600 baud, 8 data bits, no parity, 1 stop bit.
Watch out for
- Bit 14 of the fault register is set during calibration.
Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 40000 | Device type | Reads 8. | UINT16 | Read | 8 = 700 series sensor | |||
| HR | 1doc 40001 | Detectable range | Full scale; read only on FP sensors. | UINT16 | Read | ||||
| HR | 2doc 40002 | Gas concentration | Gas reading in the units of the notation string (normally %LEL). | UINT16 | Read | ||||
| HR | 3doc 40003 | AutoSpan level | Span gas concentration used for calibration. | UINT16 | Read/write | ||||
| HR | 4doc 40004 | Sensor life | Remaining sensor life. | UINT16 | % | Read | |||
| HR | 5doc 40005 | Fault status bits | Faults clear themselves when the condition clears. | BITMAP16 | Read | bit 0 = Global fault; bit 1 = AutoSpan fault; bit 2 = Temperature fault; bit 3 = 4-20 mA fault; bit 4 = Input voltage fault; bit 5 = Memory fault; bit 6 = Processor fault; bit 7 = Clearing fault; bit 8 = Stability fault; bit 9 = Range fault; bit 10 = Sensor fault; bit 11 = Zero fault; bit 12 = Sensor fault 2; bit 14 = In calibration; bit 15 = Communication error | |||
| HR | 6doc 40006 | Model number | UINT16 | Read | 1 = DM; 2 = FP; 3 = IR; 4 = TP; 5 = PID | ||||
| HR | 7doc 40007 | Days since calibration | UINT16 | days | Read | ||||
| HR | 8doc 40008 | 4-20 mA output | Current loop output value. | UINT16 | × 0.01 | mA | Read | ||
| HR | 9doc 40009 | Input voltage | UINT16 | × 0.01 | V | Read | |||
| HR | 15doc 40015 | Calibration status / enable | Read gives status; write starts an action. | UINT16 | Read/write | 0 = Read: idle; 1 = Read: zero calibration started / Write: set zero; 2 = Read: span calibration started / Write: set span; 3 = Read: span set; 4 = Read: span calibration unsuccessful; 8 = Write: signal simulation mode; 9 = Write: set FP bridge voltage; 10 = Write: set TP heater power; 11 = Write: set IR gain | |||
| HR | 16doc 40016-40021 | Gas/units notation string | Units, a space, gas name, null-terminated; first character in the low byte. | STRING[12] | Read | ||||
| HR | 23doc 40023 | Processor firmware version | 0x0102 = version 01.02. | UINT16 | Read |
Notes on this map
- Left out: special registers 40011-40014 and 40022, which the table says depend on a special-register table that this manual does not include, and 40010 temperature, whose data type (sign) is not given.
- All values are single 16-bit holding registers. Function 03 reads, 06 writes.
- The notation string stores the first character in the low byte of each register.
- Factory serial ID is 01; set it in the menu in hex.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)
What Modbus registers does the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) have?
This map lists 13 registers: 13 holding registers. 2 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 0-based (the number printed is the address on the wire). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Registers are printed 40000-40023 starting at 40000, so the digits after the leading 4 are the wire address: 40002 (gas reading) is address 2.
What are the minimum Modbus registers to integrate the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)?
Start with HR 2 Gas concentration (Gas concentration); HR 5 Fault status bits (Fault bits); HR 1 Detectable range (Full scale); HR 4 Sensor life (Sensor life); HR 8 4-20 mA output (Loop current).
How do I enable Modbus control of the Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus)?
The manual describes no separate enable step; set a unique serial ID in the sensor menu (Set Serial ID).
Where is the official Teledyne Detcon Model FP-624D MicroSafe combustible gas sensor (RS-485 Modbus) Modbus documentation?
The source is FP-624D Instruction Manual (Document #3598, Rev. 1.7), revision 2020-11-16, published free by Teledyne Detcon at https://www.teledynegasandflamedetection.com/en-us/Products/docs/fixedgas-microsafe500600-fp-624d-usermanual-english.pdf.
More Teledyne Detcon Modbus register maps
- Sensor (fixed gas detector)
Teledyne Detcon Model CX-IR infrared combustible gas sensor (Modbus RTU)
Teledyne Detcon CX-IR wired infrared gas sensors (RS-485 Modbus RTU and 4-20 mA), instruction manual Document #4428 Rev. 1.9.
Also known as: CX-IR, Detcon CX-IR - Sensor (fixed gas detector)
Teledyne Detcon Model DM-700 electrochemical toxic gas / oxygen sensor (RS-485 Modbus)
Teledyne Detcon DM-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3207, Rev. 5.9.
Also known as: DM-700, Detcon DM-700, Teledyne Detcon DM-700 - Sensor (fixed gas detector)
Teledyne Detcon Model FP-700 catalytic bead combustible gas sensor (RS-485 Modbus)
Teledyne Detcon FP-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3168, Rev. 5.7.
Also known as: FP-700, Detcon FP-700, Teledyne Detcon FP-700 - Sensor (fixed gas detector)
Teledyne Detcon Model IR-700 infrared combustible / CO2 gas sensor (RS-485 Modbus)
Teledyne Detcon IR-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3169, Rev. 4.9.
Also known as: IR-700, Detcon IR-700, Teledyne Detcon IR-700 - Sensor (fixed gas detector)
Teledyne Detcon Model PI-700 photoionization (PID) VOC sensor (RS-485 Modbus)
Teledyne Detcon PI-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3228, Rev. 4.0.
Also known as: PI-700, Detcon PI-700, Teledyne Detcon PI-700 - Sensor (fixed gas detector)
Teledyne Detcon Model TP-700 MOS (metal oxide) H2S sensor (RS-485 Modbus)
Teledyne Detcon TP-700 smart sensors with the 4-20 mA and RS-485 Modbus outputs, instruction manual Document #3150, Rev. 4.6.
Also known as: TP-700, Detcon TP-700, Teledyne Detcon TP-700 - Sensor controller (gas detection)
Teledyne Detcon Model X40 integrated alarm and control system (Modbus slave port)
Teledyne Detcon X40 gas detection controllers (8 and 32 channel, N4X and N1P enclosures), instruction manual Document #3672 Rev. 3.8, slave port register map.
Also known as: X40-08-N4X, X40-32-N4X, X40-32-N1P, X40 controller
Other gas detectors register maps
- Sensor (fixed gas detector)
Teledyne Oldham Simtronics OLCT 700 / OLCT 710 IR infrared combustible / CO2 gas detector (RS-485 Modbus)
Teledyne Oldham Simtronics OLCT 700 and OLCT 710 IR detectors with 4-20 mA and RS-485 Modbus RTU, manual NP700IRIMEN Revision E.0.
Also known as: OLCT 700 IR, OLCT 710 IR, Oldham OLCT 700 IR, 700 IR series - Sensor (extractive gas detector)
Honeywell Midas gas detector (Modbus/TCP)
Honeywell Midas extractive gas detectors (original Midas platform, software V1.08), user manual 3010M5000 revision 32, Appendix A Modbus/TCP interface.
Also known as: Midas, MIDAS gas detector - Sensor (refrigerant / toxic gas detector)
Danfoss Gas Detection Units GD Basic / Premium / Heavy Duty (Modbus RTU)
Danfoss GD Basic, Premium and Heavy Duty gas detection units on their own RS-485 Modbus port (Part 2 of the guide). The gas detection controller's X-bus map in Part 1 is not included.
Also known as: GDA, GDC, GDHC, GDHF, GDH, GD Basic, GD Premium, GD Heavy Duty - Sensor (gas detector)
Senva TG series toxic/combustible gas monitor (RS-485 Modbus)
Senva TG series RS-485 gas monitors (one or two gas sensors, optional temperature), Modbus Protocol Guide 154-0036-0A (2020-02-07).
Also known as: Senva TG, TG series - Sensor (gas transmitter / gas detector)
Analytical Technology (ATI) D12 / F12 gas transmitter (H10, catalytic bead, wet H2S sensors) Modbus interface
ATI D12 and F12 transmitters with the Modbus option fitted to H10 toxic, catalytic bead or wet H2S sensors (Appendix table 4.1). IR-sensor D12s use a different table.
Also known as: D12, F12, D12 gas transmitter, F12 gas transmitter - Sensor (extractive gas detector)
New Cosmos Electric PS-8 series extractive gas detector (Modbus TCP)
New Cosmos PS-8 series pump-type gas detectors for semiconductor plants (up to 16 sensor channels) with Ethernet Modbus TCP, Instruction Manual for Communication GAE-180-00 (December 2024).
Also known as: PS-8, PS-8 series, New Cosmos PS-8
All gas detectors Modbus register maps →
Source: FP-624D Instruction Manual · Document #3598, Rev. 1.7 · rev. 2020-11-16. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.