- Home
- Modbus register maps
- Lovato Electric
- VT1 series variable speed drives (Modbus RTU / ASCII)
Variable frequency drive · Modbus register map
Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) Modbus register map
Updated 19 November 2026
The Lovato VT1 is an AC drive whose RS-485 port supports Modbus RTU/ASCII and BACnet MS/TP. Over Modbus a master writes a command word and frequency reference and reads a block of monitor registers. This map covers the command word, frequency command, status and fault code, terminal status, output frequency, voltage, current, power, PID values, analog inputs and drive temperature.
This page lists 17 Modbus registers for the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) — 2 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Lovato Electric’s own free documentation (linked below) and checked against it.
- Manufacturer
- Lovato Electric
- Model
- VT1 series variable speed drives (Modbus RTU / ASCII)
- Equipment type
- Variable frequency drive
- Registers
- 17 (2 writable)
- Transport
- Modbus RTU, Modbus ASCII
- Default unit ID
- Not stated
- Documented addressing
- 1-based (subtract 1 for the wire address)
- Also known as
- VT1, Lovato VT1, VT1 series
Integration notes: Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII)
Write the frequency reference (wire 0x2502) and set bit 0 of the command word (wire 0x2501) to run; a single function 16 write of two registers at 0x2501 does both. Read status, fault code and output values from the block starting at wire 0x2520.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 9473 | Command word | BITMAP16 | Command word (run/stop, reset) | Read/write |
| HR 9474 | Frequency command | UINT16 | Frequency reference | Read/write |
| HR 9504 | Drive status | BITMAP16 | Drive status | Read |
| HR 9505 | Fault code | UINT16 | Fault code | Read |
| HR 9508 | Output frequency | UINT16 | Output frequency | Read |
| HR 9511 | Output current | UINT16 | Output current | Read |
Enable Modbus control & writes
Wire the drive's RS-485 port and select Modbus RTU or ASCII, the slave address and the run/frequency command source on the drive keypad; those parameter numbers are in the VT1 instruction manual, not in this protocol document.
Communication loss & watchdog
A lost connection shows Err6 on the drive; the reaction to an external abnormality written via command bit 2 follows parameter 07-09.
Byte order & addressing
- Table addresses are one above the wire address.
- Exception codes are 51h-55h, not the usual 01h-04h.
- Reads and block writes may not cross register groups.
Network setup
- Set slave address, baud rate and data format on the drive before connecting; the protocol document does not list defaults.
- Maximum frame length is 80 bytes.
- Terminate each end of the RS-485 line with a 120 ohm resistor.
Watch out for
- Do not write to the reserved word at table 2501H (wire 0x2500).
Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 9473doc 2502H | Command word | Run/stop, direction, reset, jog, S1-S5 and relay commands. | BITMAP16 | Read/write | bit 0 = Run (0 = stop); bit 1 = Reverse (0 = forward); bit 2 = External abnormality EFO; bit 3 = Fault reset; bit 4 = Jog forward; bit 5 = Jog reverse; bit 6 = Multi-function command S1; bit 7 = Multi-function command S2; bit 8 = Multi-function command S3; bit 9 = Multi-function command S4; bit 10 = Multi-function command S5; bit 12 = Relay RY1 | |||
| HR | 9474doc 2503H | Frequency command | 60.00 Hz is written as 6000. | UINT16 | × 0.01 | Hz | Read/write | ||
| HR | 9504doc 2521H | Drive status | BITMAP16 | Read | bit 0 = Running (0 = stopped); bit 1 = Reverse (0 = forward); bit 2 = Ready; bit 3 = Abnormal; bit 4 = Data setting error | ||||
| HR | 9505doc 2522H | Fault code | UINT16 | Read | 0 = Normal; 1 = Drive over heat (OH); 2 = Over current at stop (OC); 3 = Under voltage (LV); 4 = Over voltage (OV); 6 = External BB (bb); 7 = CPU error by external signal (CTE); 8 = PID feedback signal lost (PDER); 9 = EEPROM abnormal (EPR); 10 = Parameter auto-measure error (ATER); 11 = Over torque (OL3); 12 = Drive overload (OL2); 13 = Motor overload (OL1); 14 = External communication error (EFO); 15 = External stop (E.S); 16 = Parameters locked (LOC); 18 = Over current at constant speed (OC-C); 19 = Over current accelerating (OC-A); 20 = Over current decelerating (OC-D); 21 = Over current at start (OC-S); 23 = Under voltage running (LV-C); 24 = Over voltage decelerating (OV-C); 25 = Drive over heat running (OH-C); 26 = Stop at 0 speed (STP0); 27 = Direct start malfunction (STP1); 28 = Keypad emergency stop (STP2); 29 = Keypad operation error (Err1); 30 = Parameter setting error (Err2); 31 = Analog transfer error (Err4); 32 = Parameter changed during communication (Err5); 33 = Communication failure (Err6); 34 = Parameter setting error (Err7); 35 = Restore factory setting error (Err8); 38 = Copy unit parameter copy error (EPR1); 39 = Copy unit parameters incorrect (EPR2); 40 = Drive over speed (OVSP); 41 = Input phase lost (PF); 42 = Horsepower setting error (HPERR); 44 = Motor overheat error (OH4); 45 = Motor overheat alarm (OH3); 46 = Output current at current limit (CL); 47 = High pressure fault (HIPB); 48 = Low pressure fault (LOPB); 49 = PID feedback signal loss (FBLSS) | ||||
| HR | 9506doc 2523H | Terminal status | BITMAP16 | Read | bit 0 = Terminal S1; bit 1 = Terminal S2; bit 2 = Terminal S3; bit 3 = Terminal S4; bit 4 = Terminal S5; bit 6 = Relay RY1 | ||||
| HR | 9507doc 2524H | Frequency command (readback) | UINT16 | × 0.01 | Hz | Read | |||
| HR | 9508doc 2525H | Output frequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 9509doc 2526H | Output voltage command | UINT16 | × 0.1 | V | Read | |||
| HR | 9510doc 2527H | DC voltage command | UINT16 | V | Read | ||||
| HR | 9511doc 2528H | Output current | UINT16 | × 0.1 | A | Read | |||
| HR | 9513doc 252AH | Output power | UINT16 | × 0.1 | kW | Read | |||
| HR | 9514doc 252BH | PID feedback | Percent of maximum frequency. | UINT16 | × 0.1 | % | Read | ||
| HR | 9515doc 252CH | PID input | UINT16 | × 0.1 | % | Read | |||
| HR | 9516doc 252DH | AVI input value | 1000 = 10 V. | UINT16 | × 0.01 | V | Read | ||
| HR | 9517doc 252EH | ACI input value | 1000 = 10 V (as printed). | UINT16 | × 0.01 | V | Read | ||
| HR | 9521doc 2532H | Drive temperature | Heat sink or IGBT temperature. | UINT16 | × 0.1 | °C | Read | ||
| HR | 9522doc 2533H | Drive/motor rated current ratio | UINT16 | % | Read |
Notes on this map
- All registers are 16-bit holding registers: read with 03, write with 06 or 16. Reads and multi-writes must stay within one register group; at most 37 registers per RTU read and 35 per RTU write.
- Offset: the doc has no wording on it, but its three example frames all send the table number minus one (see addressing note), so that rule is applied to every register.
- Scales as printed: frequencies 100 = 1 Hz, voltage 10 = 1 V, current 10 = 1 A, power 10 = 1 kW, PID 10 = 1 %, temperature 10 = 1 °C, AVI/ACI 1000 = 10 V.
- Left out: the drive parameters. The manual says parameter gg-nn sits at register GGnnH (e.g. 08-03 at 0803H) but gives no example frame for it, so it is not clear whether that number also needs the minus-one shift.
- The AVI and ACI rows carry a footnote mark (*1) whose text is not printed in the document; check the analog scaling against the drive display.
- Write 0 to unused bits of the command word and never write to the reserved register 2501H (table numbering).
- Error responses carry codes 51h-55h (function, address, data amount, data range, writing mode) rather than the standard 01-04.
- Bit 2 of the command word is not a fault flag: setting it tells the drive about an external abnormality and makes it stop as set in 07-09 and show EFO; otherwise a communication loss shows Err6.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII)
What Modbus registers does the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) have?
This map lists 17 registers: 17 holding registers. 2 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The register tables print hex numbers one above the wire address, as all three example frames show: reading the frequency command (table 2524H) sends 25 23; writing 60.0 Hz to the frequency command (table 2503H) sends 25 02; a two-register write of run command + frequency (table 2502H-2503H) starts at 25 01. Addresses here are the table value minus one.
What are the minimum Modbus registers to integrate the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII)?
Start with HR 9473 Command word (Command word (run/stop, reset)); HR 9474 Frequency command (Frequency reference); HR 9504 Drive status (Drive status); HR 9505 Fault code (Fault code); HR 9508 Output frequency (Output frequency); HR 9511 Output current (Output current).
How do I enable Modbus control of the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII)?
Wire the drive's RS-485 port and select Modbus RTU or ASCII, the slave address and the run/frequency command source on the drive keypad; those parameter numbers are in the VT1 instruction manual, not in this protocol document.
What happens when the Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) loses Modbus communication?
A lost connection shows Err6 on the drive; the reaction to an external abnormality written via command bit 2 follows parameter 07-09.
Where is the official Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII) Modbus documentation?
The source is Variable speed drives VT1 series - Communication manual, Modbus and BACnet protocols (I646 GB I 02 21), revision 2021-02, published free by Lovato Electric at https://datasheet.lovatoelectric.com/DOWNLOAD/Technical/TechInstructions/06.%20AZIONAMENTI%20A%20VELOCITA%20VARIABILE/I646GBI02_21.pdf.
More Lovato Electric Modbus register maps
- Soft starter
Lovato Electric ADXL soft starters (Modbus RTU / ASCII / TCP)
ADXL soft starters fitted with the EXC1042 RS-485 board, per Lovato protocol addendum I454IGB03_22.
Also known as: ADXL, ADXL0030600, ADXL0045600, ADXL0060600, ADXL0075600, ADXL0085600, ADXL0115600, ADXL0135600, ADXL0162600, ADXL0195600, ADXL0250600, ADXL0320600, EXC1042 - Soft starter
Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU)
ADXNP (advanced version) soft starters fitted with the CX04 RS-485 module, per instruction manual I651 GB 02 24.
Also known as: ADXNP, CX04 - Transfer switch
Lovato Electric ATL610 automatic transfer switch controller
ATL610 ATS controller via the optical port or an EXP1010/1011/1012/1013 communication module, per protocol document I428 GB I 09 22.
Also known as: ATL610, ATL 610, EXP1012, EXP1013 - Transfer switch
Lovato Electric ATL800 / ATL900 automatic transfer switch controllers
ATL800 and ATL900 ATS controllers (document I463 GB I 11 21); LINE3, BRK3 and TB2 items are ATL900 only.
Also known as: ATL800, ATL900, ATL 800, ATL 900 - Power meter (power factor controller)
Lovato Electric DCRL3 / DCRL5 / DCRL8 power factor controllers
DCRL3, DCRL5 and DCRL8 automatic power factor controllers with optical port or EXP10xx modules (Modbus TCP on DCRL8 only), per protocol document I427 GB 05 20.
Also known as: DCRL3, DCRL5, DCRL8, DCRL 3, DCRL 5, DCRL 8 - Power meter (power analyzer)
Lovato Electric DMG7000 / DMG7500 / DMG8000 / DMG9000 power analyzers
Lovato DMG7000, DMG7500, DMG8000 and DMG9000 panel power analyzers on any Modbus port (RTU, ASCII or TCP); DMG9000-only rows are marked.
Also known as: DMG7000, DMG7500, DMG8000, DMG9000, DMG 7000, DMG 8000, DMG 9000, Lovato DMG - Pump (diesel fire pump controller)
Lovato Electric FFL700DP / FFL800DP diesel engine fire pump controllers
FFL700DP and FFL800DP diesel engine fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800DP), per protocol document I557 GB I 11 17.
Also known as: FFL700DP, FFL800DP, FFL 700 DP, FFL 800 DP - Pump (electric fire pump controller)
Lovato Electric FFL700EP / FFL800EP electric fire pump controllers
FFL700EP and FFL800EP electric fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800EP), per protocol document I589 GB I 08 22.
Also known as: FFL700EP, FFL800EP, FFL 700 EP, FFL 800 EP - Generator controller
Lovato Electric RGK610 genset controller
RGK610, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 610 - Generator controller
Lovato Electric RGK700 AMF genset controller
RGK700, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 700, RGK700 AMF - Generator controller
Lovato Electric RGK700SA stand-alone genset controller
RGK700SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 700SA, RGK700 SA - Generator controller
Lovato Electric RGK750 genset controller
RGK750, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 750 - Generator controller
Lovato Electric RGK800 AMF genset controller
RGK800, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 800, RGK800 AMF - Generator controller
Lovato Electric RGK800SA stand-alone genset controller
RGK800SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 800SA, RGK800 SA - Generator controller
Lovato Electric RGK900 genset paralleling controller
RGK900, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900 - Generator controller
Lovato Electric RGK900MC mains/master controller
RGK900MC, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900MC, RGK900 MC - Generator controller
Lovato Electric RGK900SA genset paralleling controller (stand-alone)
RGK900SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900SA, RGK900 SA
Other variable frequency drives register maps
- Variable frequency drive
NORD Drivesystems SK 540E / SK 545E frequency inverter (built-in Modbus RTU)
NORD SK 500E-series inverters from SK 540E up (SK 540E, SK 545E) on the RS485 interface, per supplementary manual BU 0050 (GB-3111).
Also known as: SK 540E, SK 545E, SK 54xE, NORDAC SK 500E series (SK 540E and above) - Actuator / valve driver (I/O module, 3 analog outputs)
Seneca Z-3AO 3-channel analog output module
Seneca Z-3AO DIN-rail module with three voltage/current outputs and RS-485 Modbus RTU, per user manual MI00260-2-EN.
Also known as: Z-3AO - Variable frequency drive
TECO-Westinghouse E510 Compact (E510N1) inverter (Modbus RTU/ASCII)
TECO-Westinghouse E510 Compact (E510N1) inverters with the built-in RS-485 port (CON2), per communication addendum DOCUMENT-TECO-E510N1-AC002 Ver01 (2017-08).
Also known as: E510N1, E510s, TECO E510 Compact - Variable frequency drive
Vacon VACON 10 AC drive (built-in Modbus RTU)
VACON 10 micro drives on the built-in RS-485 Modbus RTU port, per complete user manual DPD00717F1 (software FW0135V010).
Also known as: VACON 10, Vacon 10, VACON0010 - Variable frequency drive
Yaskawa FP605 industrial fan and pump drive (MEMOBUS/Modbus RTU)
Yaskawa FP605 drives using the built-in RS-485 port (MEMOBUS/Modbus RTU), per technical reference SIEPC7106171F.
Also known as: CIPR-FP6, FP605 drive, FP605 AC Drive for Industrial Fan and Pump Applications - Variable frequency drive (pump)
Yaskawa iQpump drive (P7U-based, legacy) - Modbus RTU
Legacy Yaskawa iQpump drives built on the P7U platform (CIMR-P7U...), per user manual TM.iQp.01, using the built-in RS-422/485 terminals R+/R-/S+/S-.
Also known as: iQpump, CIMR-P7U iQpump, iQpump Drive
All variable frequency drives Modbus register maps →
Source: Variable speed drives VT1 series - Communication manual, Modbus and BACnet protocols · I646 GB I 02 21 · rev. 2021-02. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.