- Home
- Modbus register maps
- Lovato Electric
- ADXNP soft starters with CX04 RS-485 module (Modbus RTU)
Soft starter · Modbus register map
Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) Modbus register map
Updated 19 November 2026
The Lovato ADXN is a compact soft starter with built-in bypass for pumps, fans, compressors and conveyors. Only the advanced ADXNP version talks Modbus RTU, through the CX04 RS-485 module clipped to its optical port. This map covers voltage, phase currents and powers, frequency, torque, thermal status, thyristor temperature, input and output status, and the start/stop command.
This page lists 19 Modbus registers for the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) — 1 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Lovato Electric’s own free documentation (linked below) and checked against it.
- Manufacturer
- Lovato Electric
- Model
- ADXNP soft starters with CX04 RS-485 module (Modbus RTU)
- Equipment type
- Soft starter
- Registers
- 19 (1 writable)
- Transport
- Modbus RTU
- Default unit ID
- 1
- Default serial
- 9600 baud, 8N1
- Documented addressing
- 1-based (subtract 1 for the wire address)
- 32-bit word order
- ABCD high word first (big-endian)
- Also known as
- ADXNP, CX04
Integration notes: Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU)
Fit the CX04 module, then read currents (08h-0Dh), total power (3Ah), thermal status (FB0h) and thyristor temperature (FB2h) with function 04, subtracting one from each table address. Start or stop with 1 or 0 written to 1002h.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| IR 7 | L1 current | UINT32 ABCD | L1 current | Read |
| IR 57 | Total active power | INT32 ABCD | Total active power | Read |
| IR 4015 | Motor thermal status | UINT32 ABCD | Motor thermal status | Read |
| IR 4017 | Thyristor temperature | INT32 ABCD | Thyristor temperature | Read |
| HR 4097 | Start/stop command | UINT16 | Start/stop command | Write |
Enable Modbus control & writes
Set the communication menu (M06) on the ADXNP with the LOVATO NFC app or Xpress software while the CX04 is unplugged, then clip the CX04 onto the optical port and wire RS-485 (SG, A, B) plus 24 V AC/DC to the module.
Byte order & addressing
- Table addresses are one above the wire address.
- 32-bit values are high word first.
Network setup
- Defaults: node 1, 9600 baud, 8 data bits, no parity, 1 stop bit.
- For Modbus start/stop set P04.04 = ON and keep the ST input closed; opening ST stops the motor and Modbus commands are ignored.
Watch out for
- The manual describes Modbus only for the ADXNP (advanced) version with the CX04 module.
Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| IR | 5doc 06h | L3-L1 voltage | UINT32 | ABCD | × 0.01 | V | Read | ||
| IR | 7doc 08h | L1 current | UINT32 | ABCD | × 0.0001 | A | Read | ||
| IR | 9doc 0Ah | L2 current | UINT32 | ABCD | × 0.0001 | A | Read | ||
| IR | 11doc 0Ch | L3 current | UINT32 | ABCD | × 0.0001 | A | Read | ||
| IR | 19doc 14h | L1 active power | INT32 | ABCD | × 0.00001 | kW | Read | ||
| IR | 21doc 16h | L2 active power | INT32 | ABCD | × 0.00001 | kW | Read | ||
| IR | 23doc 18h | L3 active power | INT32 | ABCD | × 0.00001 | kW | Read | ||
| IR | 49doc 32h | Frequency | UINT32 | ABCD | × 0.001 | Hz | Read | ||
| IR | 57doc 3Ah | Total active power | INT32 | ABCD | × 0.00001 | kW | Read | ||
| IR | 117doc 76h | Maximum current | UINT32 | ABCD | × 0.0001 | A | Read | ||
| IR | 119doc 78h | Torque | UINT32 | ABCD | × 0.1 | % | Read | ||
| IR | 121doc 7Ah | Maximum instantaneous current | UINT32 | ABCD | × 0.1 | % | Read | ||
| IR | 4015doc FB0h | Motor thermal status | UINT32 | ABCD | % | Read | |||
| IR | 4017doc FB2h | Thyristor temperature | INT32 | ABCD | × 0.1 | °C | Read | ||
| IR | 8447doc 2100h | ST start input status | Printed as bool (0/1); the document does not say which state is 1. | UINT16 | Read | ||||
| IR | 8511doc 2140h | Outputs status | Group word for the outputs (no bit legend printed). | UINT16 | Read | ||||
| IR | 8512doc 2141h | Output 1 (11-14) status | Printed as bool (0/1); the document does not say which state is 1. | UINT16 | Read | ||||
| IR | 8513doc 2142h | Output 2 (11-24) status | Printed as bool (0/1); the document does not say which state is 1. | UINT16 | Read | ||||
| HR | 4097doc 1002h | Start/stop command | Needs P04.04 = ON and the ST input closed. | UINT16 | Write | 0 = Stop motor; 1 = Start motor |
Notes on this map
- Measures are read with function 03 or 04 and are listed as input registers; up to 100 consecutive registers per read. The start/stop command uses function 06.
- Word order: the example answer 00 00 01 10 decodes to 272 = 27.2 °C, so 32-bit values are high word first (ABCD).
- Scales are the divisors printed in the unit column (V/100, A/10000, kW/100000, Hz/1000, %/10, °C/10).
- Left out: the status register F94h, because it is printed as 2 words with format 'Unsigned integer', so its width is unclear. The printed status values are 0 no power line, 1 ready, 2 start delay, 3 acceleration ramp, 4 current limit, 5 run, 6 bypass closed, 7 deceleration ramp, 8 alarm.
- Parameter setting over Modbus is described only by reference to the ADXL protocol document (I454), so it is not repeated here.
- Up to 31 ADXNP with CX04 can share one RS-485 line.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU)
What Modbus registers does the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) have?
This map lists 19 registers: 18 input registers, 1 holding register. 1 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The address table prints hex addresses one above the request address; the manual's example reads thyristor temperature (table 0FB2h) by sending 0F B1, 'decreased by one'. Addresses here are already reduced by one.
What byte order does the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) use for 32-bit values?
Multi-register values in this map use ABCD (high word first (big-endian)). Set your client to this order for every 32/64-bit value in the table.
What are the minimum Modbus registers to integrate the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU)?
Start with IR 7 L1 current (L1 current); IR 57 Total active power (Total active power); IR 4015 Motor thermal status (Motor thermal status); IR 4017 Thyristor temperature (Thyristor temperature); HR 4097 Start/stop command (Start/stop command).
How do I enable Modbus control of the Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU)?
Set the communication menu (M06) on the ADXNP with the LOVATO NFC app or Xpress software while the CX04 is unplugged, then clip the CX04 onto the optical port and wire RS-485 (SG, A, B) plus 24 V AC/DC to the module.
Where is the official Lovato Electric ADXNP soft starters with CX04 RS-485 module (Modbus RTU) Modbus documentation?
The source is ADXN soft starters - instruction manual (I651 GB 02 24), revision 2024-02, published free by Lovato Electric at https://datasheet.lovatoelectric.com/DOWNLOAD/Technical/TechInstructions/05.%20SOFT%20STARTER/I651GB02_24.pdf.
More Lovato Electric Modbus register maps
- Soft starter
Lovato Electric ADXL soft starters (Modbus RTU / ASCII / TCP)
ADXL soft starters fitted with the EXC1042 RS-485 board, per Lovato protocol addendum I454IGB03_22.
Also known as: ADXL, ADXL0030600, ADXL0045600, ADXL0060600, ADXL0075600, ADXL0085600, ADXL0115600, ADXL0135600, ADXL0162600, ADXL0195600, ADXL0250600, ADXL0320600, EXC1042 - Transfer switch
Lovato Electric ATL610 automatic transfer switch controller
ATL610 ATS controller via the optical port or an EXP1010/1011/1012/1013 communication module, per protocol document I428 GB I 09 22.
Also known as: ATL610, ATL 610, EXP1012, EXP1013 - Transfer switch
Lovato Electric ATL800 / ATL900 automatic transfer switch controllers
ATL800 and ATL900 ATS controllers (document I463 GB I 11 21); LINE3, BRK3 and TB2 items are ATL900 only.
Also known as: ATL800, ATL900, ATL 800, ATL 900 - Power meter (power factor controller)
Lovato Electric DCRL3 / DCRL5 / DCRL8 power factor controllers
DCRL3, DCRL5 and DCRL8 automatic power factor controllers with optical port or EXP10xx modules (Modbus TCP on DCRL8 only), per protocol document I427 GB 05 20.
Also known as: DCRL3, DCRL5, DCRL8, DCRL 3, DCRL 5, DCRL 8 - Power meter (power analyzer)
Lovato Electric DMG7000 / DMG7500 / DMG8000 / DMG9000 power analyzers
Lovato DMG7000, DMG7500, DMG8000 and DMG9000 panel power analyzers on any Modbus port (RTU, ASCII or TCP); DMG9000-only rows are marked.
Also known as: DMG7000, DMG7500, DMG8000, DMG9000, DMG 7000, DMG 8000, DMG 9000, Lovato DMG - Pump (diesel fire pump controller)
Lovato Electric FFL700DP / FFL800DP diesel engine fire pump controllers
FFL700DP and FFL800DP diesel engine fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800DP), per protocol document I557 GB I 11 17.
Also known as: FFL700DP, FFL800DP, FFL 700 DP, FFL 800 DP - Pump (electric fire pump controller)
Lovato Electric FFL700EP / FFL800EP electric fire pump controllers
FFL700EP and FFL800EP electric fire pump controllers (built-in RS-485, optical port, EXP1012T/EXP1013T modules on FFL800EP), per protocol document I589 GB I 08 22.
Also known as: FFL700EP, FFL800EP, FFL 700 EP, FFL 800 EP - Generator controller
Lovato Electric RGK610 genset controller
RGK610, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 610 - Generator controller
Lovato Electric RGK700 AMF genset controller
RGK700, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 700, RGK700 AMF - Generator controller
Lovato Electric RGK700SA stand-alone genset controller
RGK700SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 700SA, RGK700 SA - Generator controller
Lovato Electric RGK750 genset controller
RGK750, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 750 - Generator controller
Lovato Electric RGK800 AMF genset controller
RGK800, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 800, RGK800 AMF - Generator controller
Lovato Electric RGK800SA stand-alone genset controller
RGK800SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 800SA, RGK800 SA - Generator controller
Lovato Electric RGK900 genset paralleling controller
RGK900, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900 - Generator controller
Lovato Electric RGK900MC mains/master controller
RGK900MC, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900MC, RGK900 MC - Generator controller
Lovato Electric RGK900SA genset paralleling controller (stand-alone)
RGK900SA, as marked in the per-model columns of the RGK series Modbus protocol document I375 I GB 08 22.
Also known as: RGK 900SA, RGK900 SA - Variable frequency drive
Lovato Electric VT1 series variable speed drives (Modbus RTU / ASCII)
Lovato VT1 series drives on the built-in RS-485 port, per communication manual I646 GB I 02 21 (Modbus part).
Also known as: VT1, Lovato VT1, VT1 series
Other soft starters & protection relays register maps
- Motor protection relay (overload relay)
Eaton C440 electronic overload relay (via C441 Ethernet module)
Eaton C440 electronic overload relays read through a C441 Ethernet module, per Table 97 of MN04200002E.
Also known as: C440, C440 overload relay, C441U, C441V - Protection relay
Siemens Reyrolle 7SR10 Argus overcurrent and earth-fault relay (Modbus RTU)
Reyrolle 7SR10 overcurrent / earth-fault relays, default Modbus RTU point list per Communication Protocols manual C53000-L7040-C002-7 (edition 11.2025, V01.00).
Also known as: 7SR10 Argus, Reyrolle 7SR10, 7SR1003, 7SR1004 - Soft starter
Eaton S611 soft starter (via C441 Ethernet module)
Eaton S611 soft starters read through a C441R or C441T plug-in Ethernet module, per Table 98 of MN04200002E.
Also known as: S611, S611 soft starter, C441R, C441T - Motor management and protection relay
Siemens SIMOCODE pro V Modbus RTU basic unit
SIMOCODE pro V Modbus RTU basic units, per Configuration Manual 04/2015 (A5E33498234002A/RS-AA/001).
Also known as: SIMOCODE pro V Modbus, SIMOCODE pro V Modbus RTU - Soft starter (motor control)
ABB PSTX softstarter (built-in Modbus RTU)
ABB PSTX30...PSTX1250 softstarters using the built-in Modbus RTU interface on terminals 23/24 (Com3), document 1SFC132089M0201 Rev F.
Also known as: PSTX30, PSTX37, PSTX45, PSTX60, PSTX72, PSTX85, PSTX105, PSTX142, PSTX170, PSTX210, PSTX250, PSTX300, PSTX370, PSTX470, PSTX570, PSTX720, PSTX840, PSTX1050, PSTX1250 - Motor management and protection relay
Schneider Electric TeSys T LTMR motor management controller (Modbus RTU)
TeSys T LTMR Modbus controllers (LTMR..M..), with or without the LTMEV40 expansion module, per DOCA0130EN-03 (02/2024).
Also known as: TeSys T, LTMR, LTMR08MBD, LTMR27MBD, LTMR100MBD, LTMR08MFM, LTMR27MFM, LTMR100MFM, LTMR..M, LTMEV40
All soft starters & protection relays Modbus register maps →
Source: ADXN soft starters - instruction manual · I651 GB 02 24 · rev. 2024-02. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.