- Home
- Modbus register maps
- Eaton
- S611 soft starter (via C441 Ethernet module)
Soft starter · Modbus register map
Eaton S611 soft starter (via C441 Ethernet module) Modbus register map
Updated 19 November 2026
The S611 is an Eaton soft starter with built-in motor protection and metering. Through the C441 Ethernet module its data is served over Modbus TCP and RS-485 Modbus RTU. This map covers adapter I/O and comms registers, motor status and metering (300-338), the run/permissive/reset control word (400) and the start, protection and comm-loss settings (401-445).
This page lists 90 Modbus registers for the Eaton S611 soft starter (via C441 Ethernet module) — 57 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Eaton’s own free documentation (linked below) and checked against it.
- Manufacturer
- Eaton
- Model
- S611 soft starter (via C441 Ethernet module)
- Equipment type
- Soft starter
- Registers
- 90 (57 writable)
- Transport
- Modbus TCP, Modbus RTU, Modbus ASCII
- Default unit ID
- 1
- Default serial
- 19200 baud, 8E1
- Documented addressing
- 1-based (subtract 1 for the wire address)
- Also known as
- S611, S611 soft starter, C441R, C441T
Integration notes: Eaton S611 soft starter (via C441 Ethernet module)
Poll 300 for run/bypass/fault, 301-305 for current, 306-309 for voltage and 324 for trip bits. Start the motor by setting 400 bit 2 (permissive) and bit 0 (run); bit 3 resets a fault. Set 443-445 so the starter stops or faults when the network drops.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 299 | Motor status | BITMAP16 | Motor status bits | Read |
| HR 304 | Average current | UINT16 | Average current (scale by 301) | Read |
| HR 300 | Current scale factor | UINT16 | Current scale factor | Read |
| HR 308 | Average voltage | UINT16 | Average voltage | Read |
| HR 313 | Overload thermal memory | UINT16 | Thermal memory | Read |
| HR 323 | Trip reason | BITMAP16 | Trip reason bits | Read |
| HR 399 | Motor control | BITMAP16 | Run / permissive / reset | Read/write |
Enable Modbus control & writes
Modbus TCP is served by the C441 Ethernet module; the IP is set by DHCP, NV memory or the DIP switches (register 143 shows the method; 192.168.1.254 is the restore address). Remote motor control also depends on the comm idle/loss settings 251-254.
Communication loss & watchdog
Register 110 (Modbus TCP) and 159 (serial) set a com timeout in ms (0 = off); 251-254 choose whether the motor stops or holds on comm idle or loss, and 111-114 set the adapter relays' fault and idle states.
Byte order & addressing
- Register numbers are 1-based; subtract 1 on the wire.
- Coil numbers in the manual are bit views of registers (coil = 16 x (register - 1) + bit + 1), not separate data.
Network setup
- Serial port settings live in 160-163 (mode, baud, address, parity/stop) where the table lists them.
- On a C441R/C441T the RS-485 port is an extra Modbus RTU/ASCII monitoring port that serves the same register map.
Watch out for
- Several values change scale with hardware or a scale register; check the notes before trusting raw numbers.
Eaton S611 soft starter (via C441 Ethernet module) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 0doc 1 | Field inputs | Adapter input points. | BITMAP16 | Read | bit 0 = Input 1; bit 1 = Input 2; bit 2 = Input 3; bit 3 = Input 4 | |||
| HR | 1doc 2 | Control voltage | Adapter supply voltage. | UINT16 | mV | Read | |||
| HR | 4doc 5 | DIP switch value | Present DIP switch state. | BITMAP16 | Read | ||||
| HR | 100doc 101 | Field relay outputs | Adapter output relays. | BITMAP16 | Read/write | bit 0 = Output 1; bit 1 = Output 2 | |||
| HR | 109doc 110 | Modbus TCP com timeout | 0 = disabled. | UINT16 | ms | Read/write | |||
| HR | 110doc 111 | Field relay fault action | Per relay: 0 = apply fault value, 1 = no change. | BITMAP16 | Read/write | bit 0 = Relay / output 1; bit 1 = Relay / output 2 | |||
| HR | 111doc 112 | Field relay fault state | Per relay value on comm fault: 0 off, 1 on. | BITMAP16 | Read/write | bit 0 = Relay / output 1; bit 1 = Relay / output 2 | |||
| HR | 112doc 113 | Field relay idle action | Per relay: 0 = apply idle value, 1 = no change. | BITMAP16 | Read/write | bit 0 = Relay / output 1; bit 1 = Relay / output 2 | |||
| HR | 113doc 114 | Field relay idle state | Per relay value on comm idle: 0 off, 1 on. | BITMAP16 | Read/write | bit 0 = Relay / output 1; bit 1 = Relay / output 2 | |||
| HR | 142doc 143 | IP allocation method | UINT16 | Read | 0 = DHCP; 1 = Upper 3 octets from NV, last octet from DIP switches; 2 = Full address from NV memory; 3 = Restore 192.168.1.254 | ||||
| HR | 158doc 159 | Modbus serial com timeout | 0 = disabled. | UINT16 | ms | Read/write | |||
| HR | 159doc 160 | Modbus TX mode | UINT16 | Read/write | 0 = RTU; 1 = ASCII | ||||
| HR | 160doc 161 | Modbus baud rate | UINT16 | Read/write | 0 = 19200; 1 = 9600; 2 = 57600; 3 = 115200 | ||||
| HR | 161doc 162 | Modbus address | Serial slave address loaded at start-up. | UINT16 | Read/write | ||||
| HR | 162doc 163 | Modbus parity and stop bits | UINT16 | Read/write | 0 = Even, 1 stop; 1 = Odd, 1 stop; 2 = None, 2 stop; 3 = Even, 2 stop; 4 = Odd, 2 stop; 5 = None, 1 stop | ||||
| HR | 200doc 201 | Intercom status | Link between adapter and host device. | BITMAP16 | Read | bit 0 = Connected fully, no errors; bit 1 = Message fault occurred; bit 2 = Devices married, target identified; bit 3 = Basic connection established | |||
| HR | 250doc 251 | Motor ctrl idle loss act disable | 1 = keep motor state on comm idle; 0 = apply idle value (252). | UINT16 | Read/write | ||||
| HR | 251doc 252 | Motor ctrl com idle action value | UINT16 | Read/write | 0 = Ignore (no change); 1 = Stop | ||||
| HR | 252doc 253 | Motor ctrl com loss act disable | 1 = keep motor state on comm loss; 0 = apply loss value (254). | UINT16 | Read/write | ||||
| HR | 253doc 254 | Motor ctrl com loss action value | UINT16 | Read/write | 0 = Ignore (no change); 1 = Stop | ||||
| HR | 299doc 300 | Motor status | BITMAP16 | Read | bit 0 = Run; bit 2 = In bypass; bit 5 = Fault; bit 11 = Relay 1 state; bit 12 = Relay 2 state; bit 13 = Control from network; bit 14 = Permissive state | ||||
| HR | 300doc 301 | Current scale factor | Factor used to scale 302-305. | UINT16 | Read | ||||
| HR | 301doc 302 | Phase A RMS current | Scaled by register 301. | UINT16 | Read | ||||
| HR | 302doc 303 | Phase B RMS current | Scaled by register 301. | UINT16 | Read | ||||
| HR | 303doc 304 | Phase C RMS current | Scaled by register 301. | UINT16 | Read | ||||
| HR | 304doc 305 | Average current | Scaled by register 301. | UINT16 | Read | ||||
| HR | 305doc 306 | Vab RMS voltage | UINT16 | V | Read | ||||
| HR | 306doc 307 | Vbc RMS voltage | UINT16 | V | Read | ||||
| HR | 307doc 308 | Vca RMS voltage | UINT16 | V | Read | ||||
| HR | 308doc 309 | Average voltage | UINT16 | V | Read | ||||
| HR | 309doc 310 | Total kilowatts | Printed scale factor x10. | UINT16 | × 0.1 | kW | Read | ||
| HR | 310doc 311 | Apparent power factor | Power factor x 100. | UINT16 | × 0.01 | Read | |||
| HR | 311doc 312 | Power sign | Tells whether power is positive or negative (generating). | UINT16 | Read | ||||
| HR | 312doc 313 | Line frequency | UINT16 | × 0.01 | Hz | Read | |||
| HR | 313doc 314 | Overload thermal memory | 100% causes an overload trip. | UINT16 | % | Read | |||
| HR | 314doc 315 | Current unbalance | UINT16 | % | Read | ||||
| HR | 315doc 316 | Voltage unbalance | UINT16 | % | Read | ||||
| HR | 316doc 317 | Residual ground fault current | Scaling x100. | UINT16 | × 0.01 | Read | |||
| HR | 317doc 318 | Phase A pole temperature | UINT16 | × 0.1 | °C | Read | |||
| HR | 318doc 319 | Phase B pole temperature | UINT16 | × 0.1 | °C | Read | |||
| HR | 319doc 320 | Phase C pole temperature | UINT16 | × 0.1 | °C | Read | |||
| HR | 320doc 321 | Average pole temperature | UINT16 | × 0.1 | °C | Read | |||
| HR | 321doc 322 | Number of starts | Resettable via 402. | UINT16 | Read | ||||
| HR | 322doc 323 | Total run time | Resettable via 402. | UINT16 | h | Read | |||
| HR | 323doc 324 | Trip reason | BITMAP16 | Read | bit 0 = Overload; bit 1 = Jam; bit 2 = Stall; bit 3 = Current imbalance; bit 4 = Load disconnect; bit 5 = Phase loss; bit 6 = Mains fault; bit 7 = Phase reversal; bit 8 = Shorted SCR; bit 9 = SCR not firing; bit 10 = Pole over-temperature; bit 11 = Bypass dropout; bit 12 = SCR overcurrent; bit 13 = Contactor overcurrent; bit 14 = Communication fault; bit 15 = Other device fault | ||||
| HR | 324doc 325 | Fault code | Most recent fault when read as one register. | UINT16 | Read | ||||
| HR | 336doc 337 | UI firmware version | UINT16 | Read | |||||
| HR | 337doc 338 | Unit ID | Product identifier. | UINT16 | Read | ||||
| HR | 399doc 400 | Motor control | BITMAP16 | Read/write | bit 0 = Run; bit 2 = Permissive; bit 3 = Reset | ||||
| HR | 400doc 401 | Start input behavior | UINT16 | Read/write | 0 = Edge; 1 = Level | ||||
| HR | 401doc 402 | Command register | UINT16 | Read/write | 1 = Clear motor run hours; 2 = Clear motor start count; 3 = Clear fault queue; 255 = Force overload reset | ||||
| HR | 402doc 403 | Configuration reset | UINT16 | Read/write | 1 = Soft reset; 2 = Factory defaults | ||||
| HR | 403doc 404 | Overload FLA | Scaling x10. | UINT16 | × 0.1 | A | Read/write | ||
| HR | 404doc 405 | Rated voltage | Motor rated voltage. | UINT16 | Read/write | ||||
| HR | 405doc 406 | Start method | UINT16 | Read/write | 0 = Vramp (voltage ramp); 1 = Limit; 2 = Pump | ||||
| HR | 406doc 407 | Start time | Start ramp time. | UINT16 | × 0.1 | s | Read/write | ||
| HR | 407doc 408 | Initial torque | Starting torque percent. | UINT16 | % | Read/write | |||
| HR | 408doc 409 | Stop time | Stop ramp time. | UINT16 | × 0.1 | s | Read/write | ||
| HR | 409doc 410 | Pump stop time | UINT16 | s | Read/write | ||||
| HR | 410doc 411 | Kick start time | UINT16 | × 0.1 | s | Read/write | |||
| HR | 411doc 412 | Kick start initial torque | UINT16 | % | Read/write | ||||
| HR | 412doc 413 | Reset mode | UINT16 | Read/write | 0 = Manual; 1 = Auto | ||||
| HR | 413doc 414 | Fault enable bits | BITMAP16 | Read/write | bit 0 = Overload; bit 1 = Jam; bit 2 = Stall; bit 3 = Current imbalance; bit 4 = Load disconnect; bit 5 = Phase loss; bit 6 = Under voltage; bit 7 = Over voltage; bit 8 = Voltage unbalance; bit 9 = Phase reversal; bit 10 = Ground fault; bit 11 = Overload on start; bit 12 = Shorted SCR; bit 13 = SCR not firing; bit 14 = Over temperature | ||||
| HR | 414doc 415 | Overload class | UINT16 | Read/write | |||||
| HR | 415doc 416 | Jam trip level | Percent of FLA. | UINT16 | % | Read/write | |||
| HR | 416doc 417 | Jam trip delay | UINT16 | s | Read/write | ||||
| HR | 417doc 418 | Stall trip level | Percent of FLA. | UINT16 | % | Read/write | |||
| HR | 418doc 419 | Residual GF trip level | Scaling x100. | UINT16 | × 0.01 | Read/write | |||
| HR | 419doc 420 | Residual GF trip delay | UINT16 | s | Read/write | ||||
| HR | 420doc 421 | Residual GF start delay | UINT16 | s | Read/write | ||||
| HR | 421doc 422 | Current unbalance trip level | UINT16 | % | Read/write | ||||
| HR | 422doc 423 | Current unbalance trip delay | UINT16 | s | Read/write | ||||
| HR | 423doc 424 | Load disconnect trip level | Percent of rated FLA. | UINT16 | % | Read/write | |||
| HR | 424doc 425 | Load disconnect trip delay | UINT16 | s | Read/write | ||||
| HR | 425doc 426 | Load disconnect source | UINT16 | Read/write | 0 = Under power; 1 = Under current | ||||
| HR | 426doc 427 | Phase loss trip level | UINT16 | % | Read/write | ||||
| HR | 427doc 428 | Phase loss trip delay | UINT16 | s | Read/write | ||||
| HR | 428doc 429 | Under voltage level | Percent of set voltage. | UINT16 | % | Read/write | |||
| HR | 429doc 430 | Under voltage trip delay | UINT16 | s | Read/write | ||||
| HR | 430doc 431 | Over voltage level | UINT16 | % | Read/write | ||||
| HR | 431doc 432 | Over voltage trip delay | UINT16 | s | Read/write | ||||
| HR | 432doc 433 | Voltage unbalance trip level | UINT16 | % | Read/write | ||||
| HR | 433doc 434 | Voltage unbalance trip delay | UINT16 | s | Read/write | ||||
| HR | 434doc 435 | Phase sequence | UINT16 | Read/write | 1 = ABC; 2 = ACB | ||||
| HR | 435doc 436 | Fault relay config | UINT16 | Read/write | 0 = Faulted; 1 = Not faulted | ||||
| HR | 436doc 437 | Auxiliary relay configuration | UINT16 | Read/write | 0 = Faulted; 1 = Not faulted; 2 = Bypass; 3 = Not in bypass; 4 = Motor energized; 5 = Motor not energized | ||||
| HR | 437doc 438 | UI edit lock | UINT16 | Read/write | 0 = Unlocked; 1 = Locked | ||||
| HR | 442doc 443 | Communication loss timeout | UINT16 | ms | Read/write | ||||
| HR | 443doc 444 | Communication loss behavior | UINT16 | Read/write | 1 = Fault; 2 = Hold last state; 3 = Stop | ||||
| HR | 444doc 445 | Network timeout enable | Network watchdog. | UINT16 | Read/write | 0 = Disable; 1 = Enable |
Notes on this map
- Source is a distributor copy (precision-elec.com) of Eaton manual MN04200002E dated August 2012. Eaton lists a later edition (January 2016) at eaton.com, which could not be downloaded from this machine; check it for changes.
- The tables print 1-based Modbus register numbers: the production/consumption-list note says field inputs register 1 is register address 0 (address = register number - 1).
- All registers listed are single 16-bit words. Multi-word items (32-bit adapter serial number at 7, firmware/hardware revision at 9/11, IP addresses 144-154, MAC address 156) have no stated word order or layout and are left out. Signedness is not stated; values are typed unsigned.
- The same map is served over Modbus TCP and over the adapter's RS-485 Modbus RTU port; functions 01/02/03/04/05/06/15/16/23 and 43/14 are supported. Coil numbers in the manual are bit views of the same registers and are not listed here.
- Registers 1000-4000 are a user-configurable production/consumption list (custom register block); not expanded here.
- Currents 302-305 must be divided using the current scale factor in register 301 (the manual does not define the factor further), so they are left unscaled here.
- Fault code 325 starts a fault queue read newest first.
- Firmware registers 335/336 and the change-tracker queue 399 are left out (no description in the manual); command code 250 is marked unpublished and left out.
- Defaults are those printed for the C441R/C441T serial monitoring port (address 1, 19.2k, even parity, 1 stop bit, RTU); data bits and the Modbus TCP port are not stated.
- Residual ground fault current 317 and trip level 419 are printed as 'Scaling = x100' with no unit; they are scaled 0.01 here and the unit is left blank.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Eaton S611 soft starter (via C441 Ethernet module)
What Modbus registers does the Eaton S611 soft starter (via C441 Ethernet module) have?
This map lists 90 registers: 90 holding registers. 57 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Eaton S611 soft starter (via C441 Ethernet module) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers 1-based (subtract 1 for the wire address). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Tables print register numbers starting at 1; the manual states that the Modbus register address is the register number minus 1 (field inputs, register 1, is address 0).
What are the minimum Modbus registers to integrate the Eaton S611 soft starter (via C441 Ethernet module)?
Start with HR 299 Motor status (Motor status bits); HR 304 Average current (Average current (scale by 301)); HR 300 Current scale factor (Current scale factor); HR 308 Average voltage (Average voltage); HR 313 Overload thermal memory (Thermal memory); HR 323 Trip reason (Trip reason bits); HR 399 Motor control (Run / permissive / reset).
How do I enable Modbus control of the Eaton S611 soft starter (via C441 Ethernet module)?
Modbus TCP is served by the C441 Ethernet module; the IP is set by DHCP, NV memory or the DIP switches (register 143 shows the method; 192.168.1.254 is the restore address). Remote motor control also depends on the comm idle/loss settings 251-254.
What happens when the Eaton S611 soft starter (via C441 Ethernet module) loses Modbus communication?
Register 110 (Modbus TCP) and 159 (serial) set a com timeout in ms (0 = off); 251-254 choose whether the motor stops or holds on comm idle or loss, and 111-114 set the adapter relays' fault and idle states.
Where is the official Eaton S611 soft starter (via C441 Ethernet module) Modbus documentation?
The source is C441 Ethernet Module User Manual (C441R, C441T, C441U, C441V) (MN04200002E), revision 2012-08. Eaton doesn't publish it on its own website, so this map was re-typed from a free copy at https://www.precision-elec.com/wp-content/uploads/2021/01/C441-Ethernet-Module-User-Manual-C441R-C441T-C441U-C441V.pdf. It may be an older revision, so check it against the live unit.
More Eaton Modbus register maps
- Motor protection relay (overload relay)
Eaton C440 electronic overload relay (via C441 Ethernet module)
Eaton C440 electronic overload relays read through a C441 Ethernet module, per Table 97 of MN04200002E.
Also known as: C440, C440 overload relay, C441U, C441V - Motor protection relay
Eaton C441 Motor Insight motor protection relay (via C441 Ethernet module)
Eaton C441 Motor Insight relays read through a C441R or C441T plug-in Ethernet module, per Table 96 of MN04200002E.
Also known as: Motor Insight, C441BA, C441BB, C441CA, C441CB, C441DA, C441DB, C441R, C441T - Variable frequency drive (HVAC)
Eaton H-Max HVAC drive (embedded Modbus RTU / TCP)
H-Max HVAC drives with the application described in application manual MN04008006E (January 2012).
Also known as: HMX, H-Max HVAC, HMX32, HMX34 - Power meter
Eaton IQ 250 / IQ 260 Electronic Power Meter
Eaton IQ 250 and IQ 260 meters (including the L logging versions), Modbus map Appendix B of IB02601006E.
Also known as: IQ 250, IQ 260, IQ 250L, IQ 260L, IQ250, IQ260 - Power meter
Eaton Power Xpert Meter 1000 Series (PXM 1000/1100/1200/1300)
Eaton PXM 1000 series meters on the built-in RS-485 Modbus RTU port, per user manual MN150009EN (October 2018).
Also known as: PXM 1000, PXM 1100, PXM 1200, PXM 1300, PXM1000, PXM1100, PXM1200, PXM1300, Power Xpert Meter 1000 - Variable frequency drive
Eaton PowerXL DA1 variable frequency drive (Modbus RTU)
Eaton PowerXL DA1 per the Modbus RTU communication manual MN040018EN, edition 12/22.
Also known as: DA1, PowerXL DA1, DA1-12, DA1-32, DA1-34, DA1-35 - Variable frequency drive
Eaton PowerXL DB1 compact drive (Modbus RTU)
Eaton PowerXL DB1 per the Modbus RTU communication manual MN040018EN, edition 12/22.
Also known as: DB1, PowerXL DB1, DB1-12, DB1-32, DB1-34 - Variable frequency drive
Eaton PowerXL DC1 compact drive (Modbus RTU)
Eaton PowerXL DC1 per the Modbus RTU communication manual MN040018EN, edition 12/22.
Also known as: DC1, PowerXL DC1, DC1-1D, DC1-12, DC1-32, DC1-34, DC1-S2 - Variable frequency drive (variable speed starter)
Eaton PowerXL DE1 variable speed starter (Modbus RTU)
Eaton PowerXL DE1 per the Modbus RTU communication manual MN040018EN, edition 12/22.
Also known as: DE1, DE11, PowerXL DE1, PowerXL DE11, DE1-12, DE1-34, DE11-12, DE11-34 - Variable frequency drive
Eaton PowerXL DG1 / DH1 drives (on-board Modbus RTU / TCP)
PowerXL DG1 general-purpose and DH1 HVAC drives per PowerXL Series VFD Communication Manual MN040010EN (June 2018).
Also known as: DG1, DH1, PowerXL DG1, PowerXL DH1, DG1 general purpose drive, DH1 HVAC drive - Soft starter
Eaton S811+ soft starter (via C441 Ethernet module)
Eaton S811+ soft starters read through a C441 Ethernet module, per Table 99 of MN04200002E.
Also known as: S811+, S811 Plus, S811+ soft starter, C441U, C441V
Other soft starters & protection relays register maps
- Motor management and protection relay
Siemens SIMOCODE pro V Modbus RTU basic unit
SIMOCODE pro V Modbus RTU basic units, per Configuration Manual 04/2015 (A5E33498234002A/RS-AA/001).
Also known as: SIMOCODE pro V Modbus, SIMOCODE pro V Modbus RTU - Soft starter
Lovato Electric ADXL soft starters (Modbus RTU / ASCII / TCP)
ADXL soft starters fitted with the EXC1042 RS-485 board, per Lovato protocol addendum I454IGB03_22.
Also known as: ADXL, ADXL0030600, ADXL0045600, ADXL0060600, ADXL0075600, ADXL0085600, ADXL0115600, ADXL0135600, ADXL0162600, ADXL0195600, ADXL0250600, ADXL0320600, EXC1042 - Soft starter (motor control)
ABB PSTX softstarter (built-in Modbus RTU)
ABB PSTX30...PSTX1250 softstarters using the built-in Modbus RTU interface on terminals 23/24 (Com3), document 1SFC132089M0201 Rev F.
Also known as: PSTX30, PSTX37, PSTX45, PSTX60, PSTX72, PSTX85, PSTX105, PSTX142, PSTX170, PSTX210, PSTX250, PSTX300, PSTX370, PSTX470, PSTX570, PSTX720, PSTX840, PSTX1050, PSTX1250 - Motor management and protection relay
Schneider Electric TeSys T LTMR motor management controller (Modbus RTU)
TeSys T LTMR Modbus controllers (LTMR..M..), with or without the LTMEV40 expansion module, per DOCA0130EN-03 (02/2024).
Also known as: TeSys T, LTMR, LTMR08MBD, LTMR27MBD, LTMR100MBD, LTMR08MFM, LTMR27MFM, LTMR100MFM, LTMR..M, LTMEV40 - Protection relay
Siemens Reyrolle 7SR11 / 7SR12 Argus overcurrent relays (Modbus RTU)
Reyrolle 7SR11 (non-directional) and 7SR12 (directional) Argus overcurrent relays, default Modbus RTU point list in the 7SR11 & 7SR12 Complete Technical Manual (Chapter 4, Data Communications, 2015).
Also known as: 7SR11 Argus, 7SR12 Argus, Reyrolle 7SR11, Reyrolle 7SR12, 7SR120 - Soft starter (motor control)
ABB PSE softstarter (internal Modbus RTU)
ABB PSE18...PSE370 softstarters using the internal Modbus RTU interface (Modbus RTU adaptor on the front fieldbus connector), document 1SFC132367M0201 Rev B.
Also known as: PSE18, PSE25, PSE30, PSE37, PSE45, PSE60, PSE72, PSE85, PSE105, PSE142, PSE170, PSE210, PSE250, PSE300, PSE370
All soft starters & protection relays Modbus register maps →
Source: C441 Ethernet Module User Manual (C441R, C441T, C441U, C441V) · MN04200002E · rev. 2012-08 · unofficial copy. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.