- Home
- Modbus register maps
- Yaskawa
- Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)
Variable frequency drive (HVAC fan / pump) · Modbus register map
Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) Modbus register map
Updated 17 November 2026
The Z1000 is Yaskawa's HVAC fan and pump drive; its built-in RS-485 port speaks MEMOBUS/Modbus RTU, BACnet, Metasys N2 or APOGEE FLN. Commands are written to hex registers 0001H-000FH, status, fault and alarm words are read from 0020H upward, U monitors from 0040H, and parameters have their own hex addresses. This map covers the command block, status/fault/alarm words, main monitors, fault codes and the b1/H5 setup parameters.
This page lists 53 Modbus registers for the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) — 21 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Yaskawa’s own free documentation (linked below) and checked against it.
- Manufacturer
- Yaskawa
- Model
- Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)
- Equipment type
- Variable frequency drive (HVAC fan / pump)
- Registers
- 53 (21 writable)
- Transport
- Modbus RTU
- Default unit ID
- 31
- Default serial
- 9600 baud, 8N1
- Documented addressing
- hexadecimal, 0-based
- Also known as
- CIMR-ZU, Z1000 AC Drive for HVAC Fan and Pump
Integration notes: Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)
Set H5-08 = 0 and H5-01..H5-03, power-cycle, set b1-01 = 2 and b1-02 = 2, then write 0001H/0002H with function 10H and poll 0020H-002DH.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 1 | Operation commands and multi-function inputs | BITMAP16 | Run/stop and reset | Read/write |
| HR 2 | Frequency reference | UINT16 | Frequency reference | Read/write |
| HR 32 | Drive status 1 | BITMAP16 | Drive status 1 | Read |
| HR 33 | Fault contents 1 | BITMAP16 | Fault contents 1 | Read |
| HR 36 | Output frequency | UINT16 | Output frequency | Read |
| HR 38 | Output current | UINT16 | Output current | Read |
| HR 44 | Drive status 2 | BITMAP16 | Status 2 incl. comm timeout | Read |
| HR 128 | Current fault (U2-01) | UINT16 | Current fault code | Read |
Enable Modbus control & writes
H5-08 = 0 selects MEMOBUS/Modbus (1 N2, 2 P1, 3 BACnet). H5-01 address (default 1Fh), H5-02 speed (default 3 = 9600), H5-03 parity (default none); cycle power. b1-01 = 2 and b1-02 = 2 (AUTO mode sources) hand reference and run to serial communications.
Communication loss & watchdog
H5-05 = 1 (default) enables CE detection after H5-09 (default 2.0 s); H5-04 sets the reaction: 0 ramp, 1 coast, 2 fast stop, 3 alarm only (default), 4 run at d1-04. 002CH bit F flags the timeout.
Byte order & addressing
- Registers are hex and 0-based.
- No 06H function: use 10H even for one register.
- H5-11 = 0 (default) means parameter writes need an Enter command (0 to 0900H for EEPROM or 0910H for RAM); registers 0000H-001FH never need Enter.
- Enter registers are write-only; reading them returns error 02H.
Network setup
- RS-485 on terminals R+, R-, S+, S-; speeds 1200-115200 bps.
- Power-cycle after H5-01..H5-03 changes.
Watch out for
- b1-01/b1-02 are the reference and run sources for AUTO mode on the HOA keypad.
- H5-01 = 0 disables Modbus responses.
Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 1doc 0001H | Operation commands and multi-function inputs | Bits 0/1 meaning set by H5-12. | BITMAP16 | Read/write | bit 0 = H5-12=0: forward run; H5-12=1: run; bit 1 = H5-12=0: reverse run; H5-12=1: reverse direction; bit 2 = External fault (EF0); bit 3 = Fault reset; bit 4 = Multi-function input 1; bit 5 = Multi-function input 2; bit 6 = Multi-function input 3; bit 7 = Multi-function input 4; bit 8 = Multi-function input 5; bit 9 = Multi-function input 6; bit 10 = Multi-function input 7 | |||
| HR | 2doc 0002H | Frequency reference | Units set by o1-03. | UINT16 | Read/write | ||||
| HR | 6doc 0006H | PI target | Signed, 0.01 % units. | INT16 | × 0.01 | % | Read/write | ||
| HR | 9doc 0009H | Multi-function digital output settings | BITMAP16 | Read/write | bit 0 = Contact output 1 (M1-M2); bit 1 = Contact output 2 (M3-M4); bit 2 = Contact output 3 (M5-M6); bit 6 = Enable bit 7; bit 7 = Fault contact output (MA/MB-MC) | ||||
| HR | 15doc 000FH | Control selection setting | BITMAP16 | Read/write | bit 1 = PI setpoint input; bit 4 = PI2 target input from Modbus; bit 12 = Broadcast S5 enable; bit 13 = Broadcast S6 enable; bit 14 = Broadcast S7 enable | ||||
| HR | 32doc 0020H | Drive status 1 | BITMAP16 | Read | bit 0 = During run; bit 1 = During reverse; bit 2 = Drive ready; bit 3 = Fault; bit 4 = Data setting error; bit 5 = Output 1 (M1-M2); bit 6 = Output 2 (M3-M4); bit 7 = Output 3 (M5-M6); bit 14 = ComRef status; bit 15 = ComCtrl status | ||||
| HR | 33doc 0021H | Fault contents 1 | BITMAP16 | Read | bit 0 = oC / GF; bit 1 = ov; bit 2 = oL2; bit 3 = oH1 / oH2; bit 6 = FbL / FbH PI feedback loss; bit 7 = EF to EF7 external fault; bit 8 = CPF hardware fault (incl. oFx); bit 9 = oL1 / oL3 / UL3; bit 11 = Uv main circuit undervoltage; bit 12 = Uv1 / Uv2 / Uv3; bit 13 = LF / PF phase loss; bit 14 = CE / bUS communication error; bit 15 = oPr operator connection fault | ||||
| HR | 34doc 0022H | Data link status | BITMAP16 | Read | bit 0 = Writing data or switching motors; bit 3 = Upper or lower limit error; bit 4 = Data conformity error; bit 5 = Writing to EEPROM | ||||
| HR | 35doc 0023H | Frequency reference | Units set by o1-03. | UINT16 | Read | ||||
| HR | 36doc 0024H | Output frequency | Units set by o1-03. | UINT16 | Read | ||||
| HR | 38doc 0026H | Output current | UINT16 | × 0.1 | A | Read | |||
| HR | 41doc 0029H | Fault contents 2 | BITMAP16 | Read | bit 1 = GF ground fault; bit 2 = PF input phase loss; bit 3 = LF output phase loss; bit 6 = oH4 motor overheat 2 (PTC) | ||||
| HR | 42doc 002AH | Alarm contents 1 | BITMAP16 | Read | bit 2 = EF run command input error; bit 3 = bb drive baseblock; bit 4 = oL3 overtorque 1; bit 5 = oH heatsink overheat; bit 6 = ov overvoltage; bit 7 = Uv undervoltage; bit 8 = FAn cooling fan error; bit 9 = CE Modbus communication error; bit 10 = bUS option communication error; bit 11 = UL3 undertorque 1; bit 12 = oH3 motor overheat; bit 13 = FbL / FbH PI feedback loss; bit 15 = CALL serial transmission error | ||||
| HR | 43doc 002BH | Input terminal status | BITMAP16 | Read | bit 0 = S1 closed; bit 1 = S2 closed; bit 2 = S3 closed; bit 3 = S4 closed; bit 4 = S5 closed; bit 5 = S6 closed; bit 6 = S7 closed | ||||
| HR | 44doc 002CH | Drive status 2 | BITMAP16 | Read | bit 0 = During run; bit 1 = Zero speed; bit 2 = Speed agree; bit 3 = User speed agree; bit 4 = Frequency detection 1; bit 5 = Frequency detection 2; bit 6 = Drive ready; bit 7 = During undervoltage; bit 8 = During baseblock; bit 9 = Frequency reference from keypad; bit 10 = Run command from keypad; bit 11 = Over/undertorque 1; bit 12 = Frequency reference loss; bit 13 = During fault restart; bit 14 = Fault; bit 15 = Communication timeout | ||||
| HR | 45doc 002DH | Output terminal status | BITMAP16 | Read | bit 0 = Output 1 (M1-M2); bit 1 = Output 2 (M3-M4); bit 2 = Output 3 (M5-M6); bit 7 = Fault contact (MA/MB-MC) | ||||
| HR | 49doc 0031H | DC bus voltage | UINT16 | V | Read | ||||
| HR | 56doc 0038H | PI feedback | Unsigned, 100 % = max output frequency. | UINT16 | × 0.1 | % | Read | ||
| HR | 57doc 0039H | PI input | Signed, 100 % = max output frequency. | INT16 | × 0.1 | % | Read | ||
| HR | 58doc 003AH | PI output | Signed, 100 % = max output frequency. | INT16 | × 0.1 | % | Read | ||
| HR | 61doc 003DH | Communications error contents | Kept until fault reset. | BITMAP16 | Read | bit 0 = CRC error; bit 1 = Data length error; bit 3 = Parity error; bit 4 = Overrun error; bit 5 = Framing error; bit 6 = Timeout | |||
| HR | 69doc 45 | Output voltage reference (U1-06) | UINT16 | × 0.1 | V | Read | |||
| HR | 70doc 46 | DC bus voltage (U1-07) | UINT16 | V | Read | ||||
| HR | 73doc 49 | Input terminal status (U1-10) | BITMAP16 | Read | bit 0 = S1; bit 1 = S2; bit 2 = S3; bit 3 = S4; bit 4 = S5; bit 5 = S6; bit 6 = S7 | ||||
| HR | 75doc 004BH | Drive status (U1-12) | BITMAP16 | Read | bit 0 = During run; bit 1 = During zero speed; bit 2 = During reverse run; bit 3 = Fault reset signal input; bit 4 = Speed agree; bit 5 = Drive ready; bit 6 = Alarm; bit 7 = Fault; bit 8 = Operation error (oPE); bit 9 = Momentary power loss; bit 14 = ComRef / NetRef; bit 15 = ComCtrl / NetCtrl | ||||
| HR | 127doc 007FH | Alarm code | Active alarm (Table E.4). | UINT16 | Read | ||||
| HR | 128doc 0080H | Current fault (U2-01) | Fault code (Table E.3). | UINT16 | Read | 2 = Uv1; 3 = Uv2; 4 = Uv3; 6 = GF; 7 = oC; 8 = ov; 9 = oH; 10 = oH1; 11 = oL1; 12 = oL2; 13 = oL3; 17 = EF3; 18 = EF4; 19 = EF5; 20 = EF6; 21 = EF7; 27 = PF input phase loss; 28 = LF output phase loss; 29 = oH3 motor overheat (PTC); 30 = oPr operator connection; 31 = Err EEPROM write; 32 = oH4 motor overheat (PTC); 33 = CE Modbus communication error; 34 = bUS option communication error; 39 = EF0 option external fault; 40 = FbL PI feedback loss; 41 = UL3 undertorque 1; 43 = oL7 high slip braking overload; 48 = Hardware fault (incl. oFx); 54 = LF2 output current imbalance; 55 = STo pullout detection; 59 = SEr too many speed search restarts; 65 = FbH PI feedback loss; 66 = EF1; 67 = EF2; 70 = CoF current offset; 71 = PE1 PLC detection error 1; 72 = PE2 PLC detection error 2; 77 = voF output voltage detection; 82 = nSE node setup fault; 90 = UL6 motor underload; 131 = CPF02; 132 = CPF03; 135 = CPF06; 136 = CPF07; 137 = CPF08; 140 = CPF11; 141 = CPF12; 142 = CPF13; 143 = CPF14; 145 = CPF16; 146 = CPF17; 147 = CPF18; 148 = CPF19; 149 = CPF20; 150 = CPF21; 151 = CPF22; 152 = CPF23; 153 = CPF24; 154 = CPF25; 155 = CPF26; 156 = CPF27; 157 = CPF28; 158 = CPF29; 159 = CPF30; 160 = CPF31; 161 = CPF32; 162 = CPF33; 163 = CPF34; 164 = CPF35; 169 = CPF40; 170 = CPF41; 171 = CPF42; 172 = CPF43; 173 = CPF44; 174 = CPF45; 257 = oFA00; 258 = oFA01; 262 = oFA05; 263 = oFA06; 1025 = TIM time not set; 1026 = bAT operator battery low; 1027 = TdE time data error; 1028 = TiE time interval error; 1029 = ov2 overvoltage 2; 1031 = Fn1 external fan fault | |||
| HR | 129doc 0081H | Previous fault (U2-02) | UINT16 | Read | 2 = Uv1; 3 = Uv2; 4 = Uv3; 6 = GF; 7 = oC; 8 = ov; 9 = oH; 10 = oH1; 11 = oL1; 12 = oL2; 13 = oL3; 17 = EF3; 18 = EF4; 19 = EF5; 20 = EF6; 21 = EF7; 27 = PF input phase loss; 28 = LF output phase loss; 29 = oH3 motor overheat (PTC); 30 = oPr operator connection; 31 = Err EEPROM write; 32 = oH4 motor overheat (PTC); 33 = CE Modbus communication error; 34 = bUS option communication error; 39 = EF0 option external fault; 40 = FbL PI feedback loss; 41 = UL3 undertorque 1; 43 = oL7 high slip braking overload; 48 = Hardware fault (incl. oFx); 54 = LF2 output current imbalance; 55 = STo pullout detection; 59 = SEr too many speed search restarts; 65 = FbH PI feedback loss; 66 = EF1; 67 = EF2; 70 = CoF current offset; 71 = PE1 PLC detection error 1; 72 = PE2 PLC detection error 2; 77 = voF output voltage detection; 82 = nSE node setup fault; 90 = UL6 motor underload; 131 = CPF02; 132 = CPF03; 135 = CPF06; 136 = CPF07; 137 = CPF08; 140 = CPF11; 141 = CPF12; 142 = CPF13; 143 = CPF14; 145 = CPF16; 146 = CPF17; 147 = CPF18; 148 = CPF19; 149 = CPF20; 150 = CPF21; 151 = CPF22; 152 = CPF23; 153 = CPF24; 154 = CPF25; 155 = CPF26; 156 = CPF27; 157 = CPF28; 158 = CPF29; 159 = CPF30; 160 = CPF31; 161 = CPF32; 162 = CPF33; 163 = CPF34; 164 = CPF35; 169 = CPF40; 170 = CPF41; 171 = CPF42; 172 = CPF43; 173 = CPF44; 174 = CPF45; 257 = oFA00; 258 = oFA01; 262 = oFA05; 263 = oFA06; 1025 = TIM time not set; 1026 = bAT operator battery low; 1027 = TdE time data error; 1028 = TiE time interval error; 1029 = ov2 overvoltage 2; 1031 = Fn1 external fan fault | ||||
| HR | 152doc 0098H | Accumulated operation time, high (U4-01) | 10 h units. | UINT16 | × 10 | h | Read | ||
| HR | 153doc 0099H | Accumulated operation time, low (U4-01) | 1 h units. | UINT16 | h | Read | |||
| HR | 191doc 00BFH | oPE error number | Last two digits of oPE code. | UINT16 | Read | ||||
| HR | 192doc 00C0H | Fault contents 3 | BITMAP16 | Read | bit 1 = Uv1; bit 2 = Uv2; bit 3 = Uv3; bit 5 = GF; bit 6 = oC; bit 7 = ov; bit 8 = oH; bit 9 = oH1; bit 10 = oL1; bit 11 = oL2; bit 12 = oL3 | ||||
| HR | 193doc 00C1H | Fault contents 4 | BITMAP16 | Read | bit 0 = EF3; bit 1 = EF4; bit 2 = EF5; bit 3 = EF6; bit 4 = EF7; bit 6 = FAn cooling fan error; bit 10 = PF; bit 11 = LF; bit 12 = oH3; bit 13 = oPr; bit 14 = Err EEPROM write; bit 15 = oH4 | ||||
| HR | 194doc 00C2H | Fault contents 5 | BITMAP16 | Read | bit 0 = CE; bit 1 = bUS; bit 6 = EF0; bit 7 = FbL; bit 8 = UL3; bit 10 = oL7; bit 15 = Hardware fault (incl. oFx) | ||||
| HR | 195doc 00C3H | Fault contents 6 | BITMAP16 | Read | bit 5 = LF2 current imbalance; bit 6 = STo pullout detection; bit 10 = SEr too many speed search restarts | ||||
| HR | 196doc 00C4H | Fault contents 7 | BITMAP16 | Read | bit 0 = FbH; bit 1 = EF1; bit 2 = EF2; bit 5 = CoF current offset; bit 12 = voF output voltage detection | ||||
| HR | 197doc 00C5H | Fault contents 8 | BITMAP16 | Read | bit 1 = nSE node setup fault; bit 9 = UL6 motor underload | ||||
| HR | 384doc 180 | b1-01 Frequency reference selection (AUTO) | UINT16 | Read/write | 0 = HOA keypad; 1 = Terminals; 2 = Serial communications; 3 = Option card | ||||
| HR | 385doc 181 | b1-02 Run command selection (AUTO) | UINT16 | Read/write | 1 = Control circuit terminal; 2 = Serial communications; 3 = Option card | ||||
| HR | 1061doc 425 | H5-01 Drive slave address | Default 1Fh; 0 disables Modbus responses. Power-cycle. | UINT16 | Read/write | ||||
| HR | 1062doc 426 | H5-02 Communication speed | Power-cycle after change. | UINT16 | Read/write | 0 = 1200; 1 = 2400; 2 = 4800; 3 = 9600; 4 = 19200; 5 = 38400; 6 = 57600; 7 = 76800; 8 = 115200 | |||
| HR | 1063doc 427 | H5-03 Parity | Power-cycle after change. | UINT16 | Read/write | 0 = None; 1 = Even; 2 = Odd | |||
| HR | 1064doc 428 | H5-04 Stopping method after CE | UINT16 | Read/write | 0 = Ramp to stop; 1 = Coast to stop; 2 = Fast stop; 3 = Alarm only; 4 = Run at d1-04 | ||||
| HR | 1065doc 429 | H5-05 CE detection | UINT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 1066doc 42A | H5-06 Drive transmit wait time | 5-65 ms. | UINT16 | ms | Read/write | |||
| HR | 1067doc 42B | H5-07 RTS control | UINT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 1077doc 435 | H5-09 CE detection time | 0.0-10.0 s. | UINT16 | × 0.1 | s | Read/write | ||
| HR | 1078doc 436 | H5-10 Unit for register 0025H | UINT16 | Read/write | 0 = 0.1 V; 1 = 1 V | ||||
| HR | 1084doc 43C | H5-11 Enter function selection | UINT16 | Read/write | 0 = Enter command required; 1 = No Enter required | ||||
| HR | 1085doc 43D | H5-12 Run command method | UINT16 | Read/write | 0 = FWD/Stop, REV/Stop; 1 = Run/Stop, FWD/REV | ||||
| HR | 1581doc 62D | H5-08 Protocol selection | UINT16 | Read/write | 0 = MEMOBUS/Modbus; 1 = N2 (Metasys); 2 = P1 (APOGEE FLN); 3 = BACnet | ||||
| HR | 2304doc 0900H | Enter command (EEPROM) | Write 0: save to EEPROM and apply. | UINT16 | Write | ||||
| HR | 2320doc 0910H | Enter command (RAM) | Write 0: apply in RAM only. | UINT16 | Write |
Notes on this map
- This manual edition lists only 600 V class models; the register layout is the Z1000 one but check your model's manual for other voltage classes.
- 0002H/0023H/0024H frequency values follow o1-03 and are left unscaled.
- 0026H output current is printed as 0.1 A units in the data table; U1-03 (0042H) is not included because its unit footnote is model-dependent (00ABH rated current: 0.01 A for 5A0007-5A0017, 0.1 A for 5A0022-5A0242).
- Left out: 0025H output voltage (unit switched by H5-10; 0045H is included), 0027H/0047H output power (unit not printed in the data table), 0007H/0008H analog outputs (sign not stated), 003EH/003FH and 00ACH-00B8H speed/frequency in r/min or 0.01 % (sign not stated), and the RTC registers 3000H-3030H.
- Fault codes (Table E.3) are converted from hex to decimal (e.g. 0021H CE = 33); the oFA1x/oFA3x option codes are omitted from the value list. Alarm codes for 007FH (Table E.4) are not decoded.
- Only function codes 03H, 08H and 10H are supported; up to 16 registers per message.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)
What Modbus registers does the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) have?
This map lists 53 registers: 53 holding registers. 21 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Register numbers are hex and sent unchanged: the 03H example reads start address 00 20 (drive status). The parameter list gives each parameter's hex address in brackets (b1-01 = (180), H5-01 = (425), U1-06 = (45)).
What are the minimum Modbus registers to integrate the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)?
Start with HR 1 Operation commands and multi-function inputs (Run/stop and reset); HR 2 Frequency reference (Frequency reference); HR 32 Drive status 1 (Drive status 1); HR 33 Fault contents 1 (Fault contents 1); HR 36 Output frequency (Output frequency); HR 38 Output current (Output current); HR 44 Drive status 2 (Status 2 incl. comm timeout); HR 128 Current fault (U2-01) (Current fault code).
How do I enable Modbus control of the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU)?
H5-08 = 0 selects MEMOBUS/Modbus (1 N2, 2 P1, 3 BACnet). H5-01 address (default 1Fh), H5-02 speed (default 3 = 9600), H5-03 parity (default none); cycle power. b1-01 = 2 and b1-02 = 2 (AUTO mode sources) hand reference and run to serial communications.
What happens when the Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) loses Modbus communication?
H5-05 = 1 (default) enables CE detection after H5-09 (default 2.0 s); H5-04 sets the reaction: 0 ramp, 1 coast, 2 fast stop, 3 alarm only (default), 4 run at d1-04. 002CH bit F flags the timeout.
Where is the official Yaskawa Z1000 HVAC fan/pump drive (MEMOBUS/Modbus RTU) Modbus documentation?
The source is YASKAWA AC Drive Z1000 AC Drive for HVAC Fan and Pump Programming Manual (SIEP YAIZ1U 03C), published free by Yaskawa at https://www.yaskawa.com/delegate/getAttachment?documentId=SIEPYAIZ1U03&cmd=documents&documentName=SIEPYAIZ1U03.pdf.
More Yaskawa Modbus register maps
- Variable frequency drive
Yaskawa A1000 AC drive (MEMOBUS/Modbus RTU)
Yaskawa A1000 drives (CIMR-AU; 200 V, 400 V and 600 V classes) using the built-in RS-422/485 MEMOBUS/Modbus terminals (TB5), per Technical Manual SIEP C710616 41H.
Also known as: CIMR-AU, CIMR-AUA, A1000 High Performance Vector Control Drive - Variable frequency drive (HVAC)
Yaskawa E7 HVAC drive (CIMR-E7U) - Modbus RTU
Yaskawa E7 (CIMR-E7U) HVAC fan and pump drives using the built-in RS-422/485 terminals with H5-08 = 0 (Memobus/Modbus), per Parameter Access Technical Manual TM.E7.11 (rev 3016).
Also known as: CIMR-E7U, E7U, E7 Drive - Variable frequency drive
Yaskawa F7 drive (CIMR-F7U, legacy) - Modbus RTU
Yaskawa F7 (CIMR-F7U) general-purpose drives using the built-in RS-422/485 terminals R+/R-/S+/S-, per user manual TM.F7.01 Appendix D, with parameter and monitor addresses from TM.F7.11.
Also known as: CIMR-F7U, F7U, F7 Drive - Variable frequency drive
Yaskawa FP605 enclosed bypass (MEMOBUS/Modbus RTU)
Yaskawa FP605 enclosed bypass packages using the bypass board RS-485 port (TB3) with H5-08 = 0 (MEMOBUS/Modbus); Technical Reference SIEPYAIF6B01C, section 10.6.
Also known as: FP605 Enclosed Bypass, FP605 bypass package - Variable frequency drive
Yaskawa FP605 industrial fan and pump drive (MEMOBUS/Modbus RTU)
Yaskawa FP605 drives using the built-in RS-485 port (MEMOBUS/Modbus RTU), per technical reference SIEPC7106171F.
Also known as: CIPR-FP6, FP605 drive, FP605 AC Drive for Industrial Fan and Pump Applications - Variable frequency drive
Yaskawa G7 drive (CIMR-G7U, legacy) - Modbus RTU
Yaskawa G7 (CIMR-G7U) drives using built-in Modbus RTU on terminals R+/R-/S+/S-, per the Modbus Communication Manual G7 TM.G7.11 (rev 07-01).
Also known as: CIMR-G7U, G7U, G7 Drive - Variable frequency drive
Yaskawa GA500 AC drive (MEMOBUS/Modbus RTU)
Yaskawa GA500 drives using the built-in RS-485 MEMOBUS/Modbus port (terminal TB4), per technical reference SIEPC71061752 revision C.
Also known as: CIPR-GA50U, GA500 Versatile Compact - Variable frequency drive
Yaskawa GA800 AC drive (MEMOBUS/Modbus RTU)
Yaskawa GA800 drives using the built-in RS-485 MEMOBUS/Modbus port, per technical reference SIEPC71061737 revision G.
Also known as: CIPR-GA80, GA800 Industrial AC Microdrive - Variable frequency drive
Yaskawa HV305 HVAC micro drive (MEMOBUS/Modbus RTU)
Yaskawa HV305 drives using the built-in RS-485 port with H5-08 = 0 (MEMOBUS/Modbus), per technical reference SIEPYAIHV3001B.
Also known as: HV35U, HV305 drive, HV305 Versatile Compact Drive - Variable frequency drive
Yaskawa HV600 HVAC fan and pump drive (MEMOBUS/Modbus RTU)
Yaskawa HV600 drives using the built-in RS-485 port with H5-08 = 0 (MEMOBUS/Modbus), per technical reference SIEPC71061732 revision F.
Also known as: CIPR-HV60, HV600 HVAC drive - Variable frequency drive (HVAC bypass package)
Yaskawa HV600 Narrow and Enclosed Bypass (MEMOBUS/Modbus RTU)
Yaskawa HV600 Narrow and Enclosed Bypass packages using the bypass board RS-485 port (TB3) with H5-08 = 0 (Modbus); Technical Reference SIEPYAIH6B01F, section 10.6.
Also known as: HV600 Bypass, HV600 Enclosed Bypass, HV600 Narrow Bypass - Variable frequency drive (pump)
Yaskawa iQpump drive (P7U-based, legacy) - Modbus RTU
Legacy Yaskawa iQpump drives built on the P7U platform (CIMR-P7U...), per user manual TM.iQp.01, using the built-in RS-422/485 terminals R+/R-/S+/S-.
Also known as: iQpump, CIMR-P7U iQpump, iQpump Drive - Variable frequency drive
Yaskawa iQpump Micro compact pump drive (MEMOBUS/Modbus RTU)
Yaskawa iQpump Micro drives using the built-in RS-485/422 MEMOBUS/Modbus terminals, per user manual TOEP YAIQPM 03B.
Also known as: CIMR-PW (iQpump Micro), iQpump Micro AC Drive, iQpump Micro Compact Intelligent Pump Controller - Variable frequency drive
Yaskawa iQpump1000 intelligent pump drive (MEMOBUS/Modbus RTU)
Yaskawa iQpump1000 drives (CIMR-PW) using the built-in RS-485/422 MEMOBUS/Modbus terminals, per user manual TOEPYAIP1W01G.
Also known as: CIMR-PW, CIMR-PWA, iQpump1000 AC Drive - Variable frequency drive
Yaskawa iQpump605 intelligent pump controller (MEMOBUS/Modbus RTU)
Yaskawa iQpump605 drives using the built-in RS-485 port (MEMOBUS/Modbus RTU), per user manual SIEPYAIWM6502D.
Also known as: WM65W, iQpump605 drive, iQpump605 Intelligent Pump Controller - Variable frequency drive
Yaskawa J1000 compact V/f drive (MEMOBUS/Modbus RTU)
Yaskawa J1000 drives (CIMR-JU/JC) with the optional RS-422/485 MEMOBUS/Modbus interface, per Technical Manual SIEP C710606 31D.
Also known as: CIMR-JU, CIMR-JC, J1000 Compact V/f Control Drive - Variable frequency drive (HVAC bypass package)
Yaskawa P1000 Bypass for industrial fans and pumps (MEMOBUS/Modbus RTU)
P1000 Bypass bypass controller RS-485 port with Z3-01 = 0 (Modbus); Technical Manual SIEP YAIP1B 01D, appendix D.
Also known as: P1000 Bypass, P1B - Variable frequency drive
Yaskawa P1000 industrial fan and pump drive (MEMOBUS/Modbus RTU)
Yaskawa P1000 drives using the built-in RS-485/422 MEMOBUS/Modbus port (terminals R+, R-, S+, S-), per technical manual SIEP YAIP1U 01C.
Also known as: CIMR-PU, P1000 Industrial Fan and Pump Drive - Variable frequency drive (fan / pump)
Yaskawa P7 fan/pump drive (CIMR-P7U, legacy) - Modbus RTU
Yaskawa P7 (CIMR-P7U) fan and pump drives using the built-in RS-422/485 terminals R+/R-/S+/S-, per user manual TM.P7.01 Appendix D.
Also known as: CIMR-P7U, P7U, P7 Drive - Variable frequency drive (fan / pump bypass package)
Yaskawa P7B drive/bypass (legacy) - Modbus RTU
Yaskawa P7B drive/bypass packages (P7 drive CIMR-P7U inside a bypass enclosure, option V native Modbus) using the drive's RS-422/485 terminals, per technical manual TM.P7B.01 Appendix D.
Also known as: P7B, P7 Bypass - Variable frequency drive
Yaskawa U1000 Industrial MATRIX drive (MEMOBUS/Modbus RTU)
Yaskawa U1000 matrix drives using the built-in RS-422/485 MEMOBUS/Modbus port (terminals R+, R-, S+, S-), per technical manual SIEP C710636 04E.
Also known as: CIMR-UU, U1000 Industrial MATRIX Drive - Variable frequency drive
Yaskawa V1000 AC drive (MEMOBUS/Modbus RTU)
Yaskawa V1000 drives (CIMR-VU; 200 V single/three-phase and 400 V three-phase, 0.1-18.5 kW) using the built-in RS-422/485 MEMOBUS/Modbus terminals, per Technical Manual SIEP C710606 18F.
Also known as: CIMR-VU, V1000 Compact Vector Control Drive - Variable frequency drive
Yaskawa V7 / V74X compact drive (legacy) - Modbus RTU
Yaskawa V7 (CIMR-V7AM) and V74X (CIMR-V7CU) compact drives with built-in Modbus RTU (keypad RJ-45 or R+/R-/S+/S- terminals), per TM.V7.11 Rev 07-01.
Also known as: CIMR-V7AM, CIMR-V7CU, V74X - Variable frequency drive (HVAC bypass package)
Yaskawa Z1000 Bypass for HVAC fans and pumps (MEMOBUS/Modbus RTU)
Z1000 Bypass bypass controller RS-485 port with Z3-01 = 0 (Modbus); Technical Manual SIEP YAIZ1B 01F, appendix D.
Also known as: Z1000 Bypass, Z1B1 - Variable frequency drive
Yaskawa Z1000U HVAC matrix drive (MEMOBUS/Modbus RTU)
Yaskawa Z1000U HVAC matrix drives using the built-in serial terminals with H5-08 = 0 (MEMOBUS/Modbus), per programming manual SIEP C710636 10D.
Also known as: Z1000U HVAC MATRIX Drive, Z1000U Matrix
Other variable frequency drives register maps
- Variable frequency drive
ABB ACS310 pump and fan drive (embedded Modbus RTU)
ACS310 drives (01E/01U/03E/03U) using the embedded fieldbus: Modbus RTU on the built-in EIA-485 terminals 23-26 or RS-232 on the panel connector; user's manual 3AUA0000044201 Rev D.
Also known as: ACS310-01E, ACS310-01U, ACS310-03E, ACS310-03U - Variable frequency drive
ABB ACS880 industrial drive, primary control program (embedded Modbus RTU)
ACS880 drives running the primary control program (AINLX) 3.4x or later, embedded fieldbus (EFB) Modbus RTU on terminal XD2D, 58.33 Addressing mode = Mode 0 (default).
Also known as: ACS880-01, ACS880-04, ACS880-07, ACS880-11, ACS880-17, ACS880-31, ACS880-37, AINLX, ACS880 primary control program - Variable frequency drive
AutomationDirect GS2 series AC drive
All GS2 drives; status addresses and P9.xx serial-communication parameters from chapter 5 of the user manual.
Also known as: GS2-10P2, GS2-10P5, GS2-11P0, GS2-20P5, GS2-21P0, GS2-22P0, GS2-23P0, GS2-25P0, GS2-27P5, GS2-41P0, GS2-42P0, GS2-43P0, GS2-45P0, GS2-47P5 - Variable frequency drive
Danfoss VLT Compressor Drive CDS 803 (Modbus RTU)
VLT Compressor Drive CDS 803 (variable-speed compressor drive for HVAC/R) using the built-in RS-485 port with 8-30 Protocol = Modbus RTU; Modbus rules from Design Guide MG18N202 (software 1.20), parameter data from Programming Guide MG18P202 (software 2.0).
Also known as: CDS803, CDS-803, VLT Compressor Drive CDS 803 - Variable frequency drive
Eaton PowerXL DA1 variable frequency drive (Modbus RTU)
Eaton PowerXL DA1 per the Modbus RTU communication manual MN040018EN, edition 12/22.
Also known as: DA1, PowerXL DA1, DA1-12, DA1-32, DA1-34, DA1-35 - Variable frequency drive
Hitachi SJ-P1 series inverter (Modbus RTU, firmware Ver. 2.00)
Hitachi SJ-P1 inverters on the built-in RS485 port in Modbus-RTU mode, register layout of firmware Ver. 2.00 (User's Guide NT251BX-2, Rev. 6).
Also known as: SJ-P1, P1-xxxxx-L, P1-xxxxx-H
All variable frequency drives Modbus register maps →
Source: YASKAWA AC Drive Z1000 AC Drive for HVAC Fan and Pump Programming Manual · SIEP YAIZ1U 03C. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.