- Home
- Modbus register maps
- Shinko Technos
- PCA1 programmable controller (C/C5 option)
Sensor (programmable temperature controller) · Modbus register map
Shinko Technos PCA1 programmable controller (C/C5 option) Modbus register map
Updated 17 November 2026
The PCA1 is a ramp/soak controller with 16 patterns of 16 steps that draw their PID, wait, alarm, output and time-signal settings from numbered blocks. On RS-485 it speaks Shinko protocol or Modbus ASCII/RTU; every item is a signed 16-bit holding register. The map covers general settings, run/hold/advance commands, monitor values, every block table and the per-pattern repeat/link items; step items are listed for pattern 0, step 0 with the rule for the rest.
This page lists 328 Modbus registers for the Shinko Technos PCA1 programmable controller (C/C5 option) — 318 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Shinko Technos’s own free documentation (linked below) and checked against it.
- Manufacturer
- Shinko Technos
- Model
- PCA1 programmable controller (C/C5 option)
- Equipment type
- Sensor (programmable temperature controller)
- Registers
- 328 (318 writable)
- Transport
- Modbus RTU, Modbus ASCII
- Default unit ID
- 0
- Default serial
- 9600 baud, 7E1
- Documented addressing
- hexadecimal, 0-based
- Also known as
- PCA1
Integration notes: Shinko Technos PCA1 programmable controller (C/C5 option)
Select MODBUS RTU in the Communication Parameter Setting Group and give the unit a non-zero instrument number; then poll PV 0080H, current step SV 0083H, pattern/step 0085H and status 0086H-0088H, and run/stop the program with 0042H.
Minimum registers to map
Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.
| Register | Name | Type | Why | Access |
|---|---|---|---|---|
| HR 128 | PV | INT16 | Process value | Read |
| HR 131 | Current step SV | INT16 | Current step SV | Read |
| HR 133 | Current pattern and step | INT16 | Running pattern and step | Read |
| HR 136 | Current unit status | BITMAP16 | Run/hold/wait status | Read |
| HR 134 | Status flag 1 | BITMAP16 | Output, alarm and error flags | Read |
| HR 66 | Program control Run/Stop | INT16 | Program Run/Stop | Write |
| HR 63 | Pattern number for operation | INT16 | Pattern to run | Read/write |
| HR 46 | Decimal point place | INT16 | Decimal point for scaling | Read/write |
Enable Modbus control & writes
Requires the C or C5 option. In the Communication Parameter Setting Group set Communication protocol to MODBUS RTU (or ASCII), then instrument number, speed, data bit/parity and stop bit; these are keypad-only.
Byte order & addressing
- The manual's Modicon example writes 1000H as 41001, treating the hex digits as decimal; its example frames send 1000H itself as the PDU address (CRCs check), so use the hex data item directly.
- Instrument number 0 is the Modbus broadcast address; give each unit 1-95.
- Serial communication and the USB console cable cannot be used at the same time.
Network setup
- Factory defaults: Shinko protocol, instrument number 0, 9600 bps, 7 bits/even parity, 1 stop bit, 10 ms response delay.
- For Modbus RTU choose an 8-bit data format.
Watch out for
- HOLD, ADVANCE and PREVIOUS STEP return exception 17 (11H) in program standby.
- Multi-register writes to non-existent or out-of-range items are acknowledged but discarded; check by reading back.
Shinko Technos PCA1 programmable controller (C/C5 option) Modbus registers
Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.
| Table | Address | Name | Description | Type | Order | Scale | Units | Access | Values / bits |
|---|---|---|---|---|---|---|---|---|---|
| HR | 1doc 0001H | SV (fixed value control) | Raw integer; apply decimal point place (002EH). Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 2doc 0002H | OUT1 proportional band (fixed value) | Decimal point ignored. Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 3doc 0003H | Integral time (fixed value) | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 4doc 0004H | Derivative time (fixed value) | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 5doc 0005H | ARW (fixed value) | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 6doc 0006H | OUT2 proportional band (fixed value) | Decimal point ignored. Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 7doc 0007H | Alarm 1 value (fixed value) | Raw integer; apply decimal point place (002EH). Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 8doc 0008H | Alarm 2 value (fixed value) | Raw integer; apply decimal point place (002EH). Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 9doc 0009H | Alarm 3 value (fixed value) | Raw integer; apply decimal point place (002EH). Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 10doc 000AH | Alarm 4 value (fixed value) | Raw integer; apply decimal point place (002EH). Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 11doc 000BH | Auto/Manual control | INT16 | Read/write | 0 = Automatic; 1 = Manual | ||||
| HR | 12doc 000CH | Manual MV | Effective in manual control; rejected (exception 17) in automatic. | INT16 | Read/write | ||||
| HR | 13doc 000DH | AT mode | INT16 | Read/write | 0 = Normal mode; 1 = Multi mode | ||||
| HR | 14doc 000EH | AT Perform/Cancel | Rejected in program standby or manual control. | INT16 | Read/write | 0 = AT Cancel; 1 = AT Perform | |||
| HR | 15doc 000FH | Event output EV3 allocation | INT16 | Read/write | 0 = No event; 1 = High limit alarm; 2 = High limit with standby; 3 = Low limit alarm; 4 = Low limit with standby; 5 = High/Low limits alarm; 6 = High/Low limits alarm with standby; 7 = High/Low limit range alarm; 8 = High/Low limit range with standby; 9 = Process high alarm; 10 = Process high alarm with standby; 11 = Process low alarm; 12 = Process low alarm with standby; 13 = Pattern end output; 14 = Loop break alarm output; 15 = Output during AT | ||||
| HR | 16doc 0010H | Event output EV4 allocation | INT16 | Read/write | 0 = No event; 1 = High limit alarm; 2 = High limit with standby; 3 = Low limit alarm; 4 = Low limit with standby; 5 = High/Low limits alarm; 6 = High/Low limits alarm with standby; 7 = High/Low limit range alarm; 8 = High/Low limit range with standby; 9 = Process high alarm; 10 = Process high alarm with standby; 11 = Process low alarm; 12 = Process low alarm with standby; 13 = Pattern end output; 14 = Loop break alarm output; 15 = Output during AT | ||||
| HR | 17doc 0011H | EV1 alarm hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18doc 0012H | EV2 alarm hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 19doc 0013H | EV3 alarm hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 20doc 0014H | EV4 alarm hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 21doc 0015H | EV1 alarm delay time | INT16 | Read/write | |||||
| HR | 22doc 0016H | EV2 alarm delay time | INT16 | Read/write | |||||
| HR | 23doc 0017H | EV3 alarm delay time | INT16 | Read/write | |||||
| HR | 24doc 0018H | EV4 alarm delay time | INT16 | Read/write | |||||
| HR | 25doc 0019H | Loop break alarm time | INT16 | Read/write | |||||
| HR | 26doc 001AH | Loop break alarm band | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 27doc 001BH | OUT1 proportional cycle | INT16 | Read/write | |||||
| HR | 28doc 001CH | OUT1 high limit | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 29doc 001DH | OUT1 low limit | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 30doc 001EH | OUT1 ON/OFF hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 31doc 001FH | OUT1 rate-of-change | Decimal point ignored. Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 32doc 0020H | OUT2 proportional cycle | INT16 | Read/write | |||||
| HR | 33doc 0021H | OUT2 cooling method | INT16 | Read/write | 0 = Air cooling; 1 = Oil cooling; 2 = Water cooling | ||||
| HR | 34doc 0022H | OUT2 high limit | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 35doc 0023H | OUT2 low limit | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 36doc 0024H | OUT2 ON/OFF hysteresis | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 37doc 0025H | Overlap/Dead band | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 38doc 0026H | Open/Closed output dead band | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 39doc 0027H | SV high limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 40doc 0028H | SV low limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 41doc 0029H | Transmission output type | INT16 | Read/write | 0 = PV transmission; 1 = SV transmission; 2 = MV transmission | ||||
| HR | 42doc 002AH | Transmission output high limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 43doc 002BH | Transmission output low limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 44doc 002CH | Scaling high limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 45doc 002DH | Scaling low limit | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 46doc 002EH | Decimal point place | INT16 | Read/write | 0 = No decimal point; 1 = 1 digit; 2 = 2 digits; 3 = 3 digits; 4 = 4 digits | ||||
| HR | 47doc 002FH | Sensor correction | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 48doc 0030H | PV filter time constant | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 49doc 0031H | Set value lock | INT16 | Read/write | 0 = Unlock; 1 = Lock | ||||
| HR | 50doc 0032H | Step SV when program control starts | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 51doc 0033H | Program control start type | INT16 | Read/write | 0 = PV start; 1 = PVR start; 2 = SV start | ||||
| HR | 52doc 0034H | Power restore action | INT16 | Read/write | 0 = Stops; 1 = Continues; 2 = Suspends (on hold) | ||||
| HR | 53doc 0035H | Step time unit | INT16 | Read/write | 0 = Hours:Minutes; 1 = Minutes:Seconds | ||||
| HR | 54doc 0036H | Step time indication | INT16 | Read/write | 0 = Remaining time; 1 = Step time | ||||
| HR | 55doc 0037H | Step SV indication | INT16 | Read/write | 0 = SV following step progress; 1 = Step SV | ||||
| HR | 56doc 0038H | Pattern end output time | INT16 | Read/write | |||||
| HR | 57doc 0039H | Step SV hold when program ends | INT16 | Read/write | 0 = Not holding; 1 = Holding | ||||
| HR | 58doc 003AH | TS1 / status (RUN) output | INT16 | Read/write | 0 = Time signal output TS1; 1 = Status (RUN) output | ||||
| HR | 59doc 003BH | TS2 / status (HOLD) output | INT16 | Read/write | 0 = Time signal output TS2; 1 = Status (HOLD) output | ||||
| HR | 60doc 003CH | TS3 / status (WAIT) output | INT16 | Read/write | 0 = Time signal output TS3; 1 = Status (WAIT) output | ||||
| HR | 61doc 003DH | TS4 / status (FAST) output | INT16 | Read/write | 0 = Time signal output TS4; 1 = Status (FAST) output | ||||
| HR | 62doc 003EH | TS5 / status (STOP) output | INT16 | Read/write | 0 = Time signal output TS5; 1 = Status (STOP) output | ||||
| HR | 63doc 003FH | Pattern number for operation | Effective when pattern 0 is selected externally, in program standby. | INT16 | Read/write | 0 = Pattern 0; 1 = Pattern 1; 2 = Pattern 2; 3 = Pattern 3; 4 = Pattern 4; 5 = Pattern 5; 6 = Pattern 6; 7 = Pattern 7; 8 = Pattern 8; 9 = Pattern 9; 10 = Pattern 10; 11 = Pattern 11; 12 = Pattern 12; 13 = Pattern 13; 14 = Pattern 14; 15 = Pattern 15 | |||
| HR | 64doc 0040H | Pattern number for setting | INT16 | Read/write | 0 = Pattern 0; 1 = Pattern 1; 2 = Pattern 2; 3 = Pattern 3; 4 = Pattern 4; 5 = Pattern 5; 6 = Pattern 6; 7 = Pattern 7; 8 = Pattern 8; 9 = Pattern 9; 10 = Pattern 10; 11 = Pattern 11; 12 = Pattern 12; 13 = Pattern 13; 14 = Pattern 14; 15 = Pattern 15 | ||||
| HR | 65doc 0041H | Control mode | Write-only (06/10H). | INT16 | Write | 0 = Fixed value control; 1 = Program control | |||
| HR | 66doc 0042H | Program control Run/Stop | Write-only (06/10H). | INT16 | Write | 0 = Stop; 1 = Run (cancels HOLD) | |||
| HR | 67doc 0043H | Program control HOLD | Write-only; rejected in standby. | INT16 | Write | 1 = HOLD | |||
| HR | 68doc 0044H | Program control ADVANCE | Write-only; rejected in standby. | INT16 | Write | 1 = ADVANCE | |||
| HR | 69doc 0045H | Program control PREVIOUS STEP | Write-only; rejected in standby. | INT16 | Write | 1 = PREVIOUS STEP | |||
| HR | 70doc 0046H | Open output time | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 71doc 0047H | Closed output time | Marked (*1): may read 0 and ignore writes. | INT16 | Read/write | ||||
| HR | 72doc 0048H | Input type | DC inputs scale -2000 to 10000. | INT16 | Read/write | 0 = K -200 to 1370 C; 1 = K -200.0 to 400.0 C; 2 = J -200 to 1000 C; 3 = R 0 to 1760 C; 4 = S 0 to 1760 C; 5 = B 0 to 1820 C; 6 = E -200 to 800 C; 7 = T -200.0 to 400.0 C; 8 = N -200 to 1300 C; 9 = PL-II 0 to 1390 C; 10 = C (W/Re5-26) 0 to 2315 C; 11 = Pt100 -200.0 to 850.0 C; 12 = JPt100 -200.0 to 500.0 C; 13 = Pt100 -200 to 850 C; 14 = JPt100 -200 to 500 C; 15 = Pt100 -100.0 to 100.0 C; 16 = Pt100 -100.0 to 500.0 C; 17 = K -328 to 2498 F; 18 = K -328.0 to 752.0 F; 19 = J -328 to 1832 F; 20 = R 32 to 3200 F; 21 = S 32 to 3200 F; 22 = B 32 to 3308 F; 23 = E -328 to 1472 F; 24 = T -328.0 to 752.0 F; 25 = N -328 to 2372 F; 26 = PL-II 32 to 2534 F; 27 = C (W/Re5-26) 32 to 4199 F; 28 = Pt100 -328.0 to 1562.0 F; 29 = JPt100 -328.0 to 932.0 F; 30 = Pt100 -328 to 1562 F; 31 = JPt100 -328 to 932 F; 32 = Pt100 -148.0 to 212.0 F; 33 = Pt100 -148.0 to 932.0 F; 34 = 4 to 20 mA; 35 = 0 to 20 mA; 36 = 0 to 10 mV; 37 = -10 to 10 mV; 38 = 0 to 50 mV; 39 = 0 to 100 mV; 40 = 0 to 1 V; 41 = 0 to 5 V; 42 = 1 to 5 V; 43 = 0 to 10 V | |||
| HR | 73doc 0049H | AT bias | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 74doc 004AH | Direct/Reverse action | INT16 | Read/write | 0 = Reverse action; 1 = Direct action | ||||
| HR | 75doc 004BH | Event output EV1 allocation | INT16 | Read/write | 0 = No event; 1 = High limit alarm; 2 = High limit with standby; 3 = Low limit alarm; 4 = Low limit with standby; 5 = High/Low limits alarm; 6 = High/Low limits alarm with standby; 7 = High/Low limit range alarm; 8 = High/Low limit range with standby; 9 = Process high alarm; 10 = Process high alarm with standby; 11 = Process low alarm; 12 = Process low alarm with standby; 13 = Pattern end output; 14 = Loop break alarm output; 15 = Output during AT | ||||
| HR | 76doc 004CH | Event output EV2 allocation | INT16 | Read/write | 0 = No event; 1 = High limit alarm; 2 = High limit with standby; 3 = Low limit alarm; 4 = Low limit with standby; 5 = High/Low limits alarm; 6 = High/Low limits alarm with standby; 7 = High/Low limit range alarm; 8 = High/Low limit range with standby; 9 = Process high alarm; 10 = Process high alarm with standby; 11 = Process low alarm; 12 = Process low alarm with standby; 13 = Pattern end output; 14 = Loop break alarm output; 15 = Output during AT | ||||
| HR | 77doc 004DH | EV1 alarm energized/de-energized | INT16 | Read/write | 0 = Energized; 1 = De-energized | ||||
| HR | 78doc 004EH | EV2 alarm energized/de-energized | INT16 | Read/write | 0 = Energized; 1 = De-energized | ||||
| HR | 79doc 004FH | EV3 alarm energized/de-energized | INT16 | Read/write | 0 = Energized; 1 = De-energized | ||||
| HR | 80doc 0050H | EV4 alarm energized/de-energized | INT16 | Read/write | 0 = Energized; 1 = De-energized | ||||
| HR | 81doc 0051H | Program start Auto/Manual | INT16 | Read/write | 0 = Manual start; 1 = Automatic start | ||||
| HR | 82doc 0052H | Overshoot suppression | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 83doc 0053H | Overshoot suppression factor | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 84doc 0054H | Output status on input error | INT16 | Read/write | 0 = Output OFF; 1 = Output ON | ||||
| HR | 85doc 0055H | Backlight selection | INT16 | Read/write | 0 = All are backlit; 1 = PV display is backlit | ||||
| HR | 86doc 0056H | PV color | INT16 | Read/write | 0 = Green; 1 = Red; 2 = Orange; 3 = Alarm ON: green to red; 4 = Alarm ON: orange to red; 5 = Changes continuously; 6 = Changes continuously + alarm ON red | ||||
| HR | 87doc 0057H | PV color range | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 88doc 0058H | Backlight time | INT16 | Read/write | |||||
| HR | 89doc 0059H | Response delay time | INT16 | ms | Read/write | ||||
| HR | 112doc 0070H | Key operation change flag clearing | INT16 | Write | 1 = Clear flag | ||||
| HR | 128doc 0080H | PV | Process value. Raw integer; apply decimal point place (002EH). | INT16 | Read | ||||
| HR | 129doc 0081H | OUT1 MV | INT16 | Read | |||||
| HR | 130doc 0082H | OUT2 MV | INT16 | Read | |||||
| HR | 131doc 0083H | Current step SV | Raw integer; apply decimal point place (002EH). | INT16 | Read | ||||
| HR | 132doc 0084H | Current step remaining time | INT16 | Read | |||||
| HR | 133doc 0085H | Current pattern and step | Lowest hex digit = pattern, next hex digit = step (0 when stopped). | INT16 | Read | ||||
| HR | 134doc 0086H | Status flag 1 | BITMAP16 | Read | bit 0 = OUT1 on; bit 1 = OUT2 on; bit 2 = EV1 output on; bit 3 = EV2 output on; bit 4 = EV3 output on; bit 5 = EV4 output on; bit 6 = Loop break alarm; bit 7 = Overscale; bit 8 = Underscale; bit 15 = Changed by keypad | ||||
| HR | 135doc 0087H | Status flag 2 | BITMAP16 | Read | bit 0 = Time signal 1 (RUN) output; bit 1 = Time signal 2 (HOLD) output; bit 2 = Time signal 3 (WAIT) output; bit 3 = Time signal 4 (FAST) output; bit 4 = Time signal 5 (STOP) output; bit 5 = Time signal 6 output; bit 6 = Time signal 7 output; bit 7 = Time signal 8 output | ||||
| HR | 136doc 0088H | Current unit status | BITMAP16 | Read | bit 0 = Program control (fixed); bit 1 = Manual; bit 2 = AT performing; bit 3 = Program control running; bit 4 = HOLD; bit 5 = WAIT; bit 6 = Pattern end output on; bit 7 = SV hold | ||||
| HR | 137doc 0089H | Pattern selected by event input | INT16 | Read | |||||
| HR | 4096doc 1000H | P0 step 0 SV | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 4097doc 1001H | P0 step 0 time | Smaller unit of 0035H; FFFFH = hold step. | INT16 | Read/write | ||||
| HR | 4098doc 1002H | P0 step 0 PID block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9 | ||||
| HR | 4099doc 1003H | P0 step 0 time signal 1 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4100doc 1004H | P0 step 0 time signal 2 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4101doc 1005H | P0 step 0 time signal 3 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4102doc 1006H | P0 step 0 time signal 4 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4103doc 1007H | P0 step 0 time signal 5 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4104doc 1008H | P0 step 0 time signal 6 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4105doc 1009H | P0 step 0 time signal 7 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4106doc 100AH | P0 step 0 time signal 8 block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9; 10 = Block 10; 11 = Block 11; 12 = Block 12; 13 = Block 13; 14 = Block 14; 15 = Block 15 | ||||
| HR | 4107doc 100BH | P0 step 0 wait block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9 | ||||
| HR | 4108doc 100CH | P0 step 0 alarm block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9 | ||||
| HR | 4109doc 100DH | P0 step 0 output block | INT16 | Read/write | 0 = Block 0; 1 = Block 1; 2 = Block 2; 3 = Block 3; 4 = Block 4; 5 = Block 5; 6 = Block 6; 7 = Block 7; 8 = Block 8; 9 = Block 9 | ||||
| HR | 8192doc 2000H | PID block 0 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 8193doc 2001H | PID block 0 integral time | INT16 | Read/write | |||||
| HR | 8194doc 2002H | PID block 0 derivative time | INT16 | Read/write | |||||
| HR | 8195doc 2003H | PID block 0 ARW | INT16 | Read/write | |||||
| HR | 8196doc 2004H | PID block 0 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 8448doc 2100H | PID block 1 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 8449doc 2101H | PID block 1 integral time | INT16 | Read/write | |||||
| HR | 8450doc 2102H | PID block 1 derivative time | INT16 | Read/write | |||||
| HR | 8451doc 2103H | PID block 1 ARW | INT16 | Read/write | |||||
| HR | 8452doc 2104H | PID block 1 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 8704doc 2200H | PID block 2 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 8705doc 2201H | PID block 2 integral time | INT16 | Read/write | |||||
| HR | 8706doc 2202H | PID block 2 derivative time | INT16 | Read/write | |||||
| HR | 8707doc 2203H | PID block 2 ARW | INT16 | Read/write | |||||
| HR | 8708doc 2204H | PID block 2 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 8960doc 2300H | PID block 3 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 8961doc 2301H | PID block 3 integral time | INT16 | Read/write | |||||
| HR | 8962doc 2302H | PID block 3 derivative time | INT16 | Read/write | |||||
| HR | 8963doc 2303H | PID block 3 ARW | INT16 | Read/write | |||||
| HR | 8964doc 2304H | PID block 3 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 9216doc 2400H | PID block 4 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 9217doc 2401H | PID block 4 integral time | INT16 | Read/write | |||||
| HR | 9218doc 2402H | PID block 4 derivative time | INT16 | Read/write | |||||
| HR | 9219doc 2403H | PID block 4 ARW | INT16 | Read/write | |||||
| HR | 9220doc 2404H | PID block 4 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 9472doc 2500H | PID block 5 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 9473doc 2501H | PID block 5 integral time | INT16 | Read/write | |||||
| HR | 9474doc 2502H | PID block 5 derivative time | INT16 | Read/write | |||||
| HR | 9475doc 2503H | PID block 5 ARW | INT16 | Read/write | |||||
| HR | 9476doc 2504H | PID block 5 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 9728doc 2600H | PID block 6 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 9729doc 2601H | PID block 6 integral time | INT16 | Read/write | |||||
| HR | 9730doc 2602H | PID block 6 derivative time | INT16 | Read/write | |||||
| HR | 9731doc 2603H | PID block 6 ARW | INT16 | Read/write | |||||
| HR | 9732doc 2604H | PID block 6 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 9984doc 2700H | PID block 7 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 9985doc 2701H | PID block 7 integral time | INT16 | Read/write | |||||
| HR | 9986doc 2702H | PID block 7 derivative time | INT16 | Read/write | |||||
| HR | 9987doc 2703H | PID block 7 ARW | INT16 | Read/write | |||||
| HR | 9988doc 2704H | PID block 7 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 10240doc 2800H | PID block 8 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 10241doc 2801H | PID block 8 integral time | INT16 | Read/write | |||||
| HR | 10242doc 2802H | PID block 8 derivative time | INT16 | Read/write | |||||
| HR | 10243doc 2803H | PID block 8 ARW | INT16 | Read/write | |||||
| HR | 10244doc 2804H | PID block 8 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 10496doc 2900H | PID block 9 OUT1 proportional band | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 10497doc 2901H | PID block 9 integral time | INT16 | Read/write | |||||
| HR | 10498doc 2902H | PID block 9 derivative time | INT16 | Read/write | |||||
| HR | 10499doc 2903H | PID block 9 ARW | INT16 | Read/write | |||||
| HR | 10500doc 2904H | PID block 9 OUT2 proportional band | INT16 | Read/write | |||||
| HR | 12288doc 3000H | Wait block 0 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 12544doc 3100H | Wait block 1 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 12800doc 3200H | Wait block 2 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 13056doc 3300H | Wait block 3 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 13312doc 3400H | Wait block 4 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 13568doc 3500H | Wait block 5 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 13824doc 3600H | Wait block 6 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 14080doc 3700H | Wait block 7 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 14336doc 3800H | Wait block 8 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 14592doc 3900H | Wait block 9 wait value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16384doc 4000H | Alarm block 0 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16385doc 4001H | Alarm block 0 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16386doc 4002H | Alarm block 0 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16387doc 4003H | Alarm block 0 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16640doc 4100H | Alarm block 1 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16641doc 4101H | Alarm block 1 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16642doc 4102H | Alarm block 1 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16643doc 4103H | Alarm block 1 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16896doc 4200H | Alarm block 2 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16897doc 4201H | Alarm block 2 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16898doc 4202H | Alarm block 2 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 16899doc 4203H | Alarm block 2 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17152doc 4300H | Alarm block 3 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17153doc 4301H | Alarm block 3 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17154doc 4302H | Alarm block 3 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17155doc 4303H | Alarm block 3 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17408doc 4400H | Alarm block 4 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17409doc 4401H | Alarm block 4 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17410doc 4402H | Alarm block 4 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17411doc 4403H | Alarm block 4 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17664doc 4500H | Alarm block 5 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17665doc 4501H | Alarm block 5 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17666doc 4502H | Alarm block 5 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17667doc 4503H | Alarm block 5 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17920doc 4600H | Alarm block 6 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17921doc 4601H | Alarm block 6 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17922doc 4602H | Alarm block 6 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 17923doc 4603H | Alarm block 6 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18176doc 4700H | Alarm block 7 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18177doc 4701H | Alarm block 7 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18178doc 4702H | Alarm block 7 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18179doc 4703H | Alarm block 7 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18432doc 4800H | Alarm block 8 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18433doc 4801H | Alarm block 8 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18434doc 4802H | Alarm block 8 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18435doc 4803H | Alarm block 8 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18688doc 4900H | Alarm block 9 EV1 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18689doc 4901H | Alarm block 9 EV2 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18690doc 4902H | Alarm block 9 EV3 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 18691doc 4903H | Alarm block 9 EV4 alarm value | Raw integer; apply decimal point place (002EH). | INT16 | Read/write | ||||
| HR | 20480doc 5000H | Output block 0 OUT1 high limit | INT16 | Read/write | |||||
| HR | 20481doc 5001H | Output block 0 OUT1 low limit | INT16 | Read/write | |||||
| HR | 20482doc 5002H | Output block 0 OUT2 high limit | INT16 | Read/write | |||||
| HR | 20483doc 5003H | Output block 0 OUT2 low limit | INT16 | Read/write | |||||
| HR | 20484doc 5004H | Output block 0 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 20736doc 5100H | Output block 1 OUT1 high limit | INT16 | Read/write | |||||
| HR | 20737doc 5101H | Output block 1 OUT1 low limit | INT16 | Read/write | |||||
| HR | 20738doc 5102H | Output block 1 OUT2 high limit | INT16 | Read/write | |||||
| HR | 20739doc 5103H | Output block 1 OUT2 low limit | INT16 | Read/write | |||||
| HR | 20740doc 5104H | Output block 1 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 20992doc 5200H | Output block 2 OUT1 high limit | INT16 | Read/write | |||||
| HR | 20993doc 5201H | Output block 2 OUT1 low limit | INT16 | Read/write | |||||
| HR | 20994doc 5202H | Output block 2 OUT2 high limit | INT16 | Read/write | |||||
| HR | 20995doc 5203H | Output block 2 OUT2 low limit | INT16 | Read/write | |||||
| HR | 20996doc 5204H | Output block 2 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 21248doc 5300H | Output block 3 OUT1 high limit | INT16 | Read/write | |||||
| HR | 21249doc 5301H | Output block 3 OUT1 low limit | INT16 | Read/write | |||||
| HR | 21250doc 5302H | Output block 3 OUT2 high limit | INT16 | Read/write | |||||
| HR | 21251doc 5303H | Output block 3 OUT2 low limit | INT16 | Read/write | |||||
| HR | 21252doc 5304H | Output block 3 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 21504doc 5400H | Output block 4 OUT1 high limit | INT16 | Read/write | |||||
| HR | 21505doc 5401H | Output block 4 OUT1 low limit | INT16 | Read/write | |||||
| HR | 21506doc 5402H | Output block 4 OUT2 high limit | INT16 | Read/write | |||||
| HR | 21507doc 5403H | Output block 4 OUT2 low limit | INT16 | Read/write | |||||
| HR | 21508doc 5404H | Output block 4 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 21760doc 5500H | Output block 5 OUT1 high limit | INT16 | Read/write | |||||
| HR | 21761doc 5501H | Output block 5 OUT1 low limit | INT16 | Read/write | |||||
| HR | 21762doc 5502H | Output block 5 OUT2 high limit | INT16 | Read/write | |||||
| HR | 21763doc 5503H | Output block 5 OUT2 low limit | INT16 | Read/write | |||||
| HR | 21764doc 5504H | Output block 5 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 22016doc 5600H | Output block 6 OUT1 high limit | INT16 | Read/write | |||||
| HR | 22017doc 5601H | Output block 6 OUT1 low limit | INT16 | Read/write | |||||
| HR | 22018doc 5602H | Output block 6 OUT2 high limit | INT16 | Read/write | |||||
| HR | 22019doc 5603H | Output block 6 OUT2 low limit | INT16 | Read/write | |||||
| HR | 22020doc 5604H | Output block 6 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 22272doc 5700H | Output block 7 OUT1 high limit | INT16 | Read/write | |||||
| HR | 22273doc 5701H | Output block 7 OUT1 low limit | INT16 | Read/write | |||||
| HR | 22274doc 5702H | Output block 7 OUT2 high limit | INT16 | Read/write | |||||
| HR | 22275doc 5703H | Output block 7 OUT2 low limit | INT16 | Read/write | |||||
| HR | 22276doc 5704H | Output block 7 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 22528doc 5800H | Output block 8 OUT1 high limit | INT16 | Read/write | |||||
| HR | 22529doc 5801H | Output block 8 OUT1 low limit | INT16 | Read/write | |||||
| HR | 22530doc 5802H | Output block 8 OUT2 high limit | INT16 | Read/write | |||||
| HR | 22531doc 5803H | Output block 8 OUT2 low limit | INT16 | Read/write | |||||
| HR | 22532doc 5804H | Output block 8 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 22784doc 5900H | Output block 9 OUT1 high limit | INT16 | Read/write | |||||
| HR | 22785doc 5901H | Output block 9 OUT1 low limit | INT16 | Read/write | |||||
| HR | 22786doc 5902H | Output block 9 OUT2 high limit | INT16 | Read/write | |||||
| HR | 22787doc 5903H | Output block 9 OUT2 low limit | INT16 | Read/write | |||||
| HR | 22788doc 5904H | Output block 9 OUT1 rate-of-change | Decimal point ignored. | INT16 | Read/write | ||||
| HR | 24576doc 6000H | Time signal block 0 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 24577doc 6001H | Time signal block 0 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 24832doc 6100H | Time signal block 1 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 24833doc 6101H | Time signal block 1 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25088doc 6200H | Time signal block 2 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25089doc 6201H | Time signal block 2 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25344doc 6300H | Time signal block 3 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25345doc 6301H | Time signal block 3 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25600doc 6400H | Time signal block 4 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25601doc 6401H | Time signal block 4 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25856doc 6500H | Time signal block 5 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 25857doc 6501H | Time signal block 5 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26112doc 6600H | Time signal block 6 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26113doc 6601H | Time signal block 6 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26368doc 6700H | Time signal block 7 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26369doc 6701H | Time signal block 7 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26624doc 6800H | Time signal block 8 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26625doc 6801H | Time signal block 8 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26880doc 6900H | Time signal block 9 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 26881doc 6901H | Time signal block 9 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27136doc 6A00H | Time signal block 10 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27137doc 6A01H | Time signal block 10 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27392doc 6B00H | Time signal block 11 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27393doc 6B01H | Time signal block 11 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27648doc 6C00H | Time signal block 12 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27649doc 6C01H | Time signal block 12 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27904doc 6D00H | Time signal block 13 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 27905doc 6D01H | Time signal block 13 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 28160doc 6E00H | Time signal block 14 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 28161doc 6E01H | Time signal block 14 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 28416doc 6F00H | Time signal block 15 OFF time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 28417doc 6F01H | Time signal block 15 ON time | Smaller unit of 0035H. | INT16 | Read/write | ||||
| HR | 28672doc 7000H | Pattern 0 number of repetitions | INT16 | Read/write | |||||
| HR | 28673doc 7001H | Pattern 0 to 1 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 28928doc 7100H | Pattern 1 number of repetitions | INT16 | Read/write | |||||
| HR | 28929doc 7101H | Pattern 1 to 2 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 29184doc 7200H | Pattern 2 number of repetitions | INT16 | Read/write | |||||
| HR | 29185doc 7201H | Pattern 2 to 3 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 29440doc 7300H | Pattern 3 number of repetitions | INT16 | Read/write | |||||
| HR | 29441doc 7301H | Pattern 3 to 4 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 29696doc 7400H | Pattern 4 number of repetitions | INT16 | Read/write | |||||
| HR | 29697doc 7401H | Pattern 4 to 5 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 29952doc 7500H | Pattern 5 number of repetitions | INT16 | Read/write | |||||
| HR | 29953doc 7501H | Pattern 5 to 6 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 30208doc 7600H | Pattern 6 number of repetitions | INT16 | Read/write | |||||
| HR | 30209doc 7601H | Pattern 6 to 7 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 30464doc 7700H | Pattern 7 number of repetitions | INT16 | Read/write | |||||
| HR | 30465doc 7701H | Pattern 7 to 8 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 30720doc 7800H | Pattern 8 number of repetitions | INT16 | Read/write | |||||
| HR | 30721doc 7801H | Pattern 8 to 9 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 30976doc 7900H | Pattern 9 number of repetitions | INT16 | Read/write | |||||
| HR | 30977doc 7901H | Pattern 9 to 10 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 31232doc 7A00H | Pattern 10 number of repetitions | INT16 | Read/write | |||||
| HR | 31233doc 7A01H | Pattern 10 to 11 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 31488doc 7B00H | Pattern 11 number of repetitions | INT16 | Read/write | |||||
| HR | 31489doc 7B01H | Pattern 11 to 12 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 31744doc 7C00H | Pattern 12 number of repetitions | INT16 | Read/write | |||||
| HR | 31745doc 7C01H | Pattern 12 to 13 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 32000doc 7D00H | Pattern 13 number of repetitions | INT16 | Read/write | |||||
| HR | 32001doc 7D01H | Pattern 13 to 14 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 32256doc 7E00H | Pattern 14 number of repetitions | INT16 | Read/write | |||||
| HR | 32257doc 7E01H | Pattern 14 to 15 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled | ||||
| HR | 32512doc 7F00H | Pattern 15 number of repetitions | INT16 | Read/write | |||||
| HR | 32513doc 7F01H | Pattern 15 to 0 link | INT16 | Read/write | 0 = Disabled; 1 = Enabled |
Notes on this map
- Step items: address = 1000H + pattern x 100H + step x 10H + item, pattern and step 0-F, item 0 (SV) to D (output block). Only pattern 0, step 0 is listed here; all 256 steps use the same item layout.
- Block items: PID 2k00H-2k04H, wait 3k00H, alarm 4k00H-4k03H, output 5k00H-5k04H (k = block 0-9), time signal 6k00H-6k01H (k = 0-F), repetitions/link 7p00H-7p01H (p = pattern 0-F).
- All data are 16-bit two's complement; values with a decimal point are sent as whole numbers.
- Units of PID times, limits and MV are not printed in the command table.
Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.
Questions about the Shinko Technos PCA1 programmable controller (C/C5 option)
What Modbus registers does the Shinko Technos PCA1 programmable controller (C/C5 option) have?
This map lists 328 registers: 328 holding registers. 318 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.
Are the Shinko Technos PCA1 programmable controller (C/C5 option) Modbus addresses 0-based or 1-based?
The manufacturer's document numbers registers hexadecimal, 0-based. Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. Data items are hex (0080H, 1000H) and are sent unchanged as the Modbus holding-register address. The manual says the Modicon number is the data item plus 40001. The RTU examples read PV at 0080H and pattern 0 step 0 SV at 1000H (CRCs 85E2H and 80CAH checked).
What are the minimum Modbus registers to integrate the Shinko Technos PCA1 programmable controller (C/C5 option)?
Start with HR 128 PV (Process value); HR 131 Current step SV (Current step SV); HR 133 Current pattern and step (Running pattern and step); HR 136 Current unit status (Run/hold/wait status); HR 134 Status flag 1 (Output, alarm and error flags); HR 66 Program control Run/Stop (Program Run/Stop); HR 63 Pattern number for operation (Pattern to run); HR 46 Decimal point place (Decimal point for scaling).
How do I enable Modbus control of the Shinko Technos PCA1 programmable controller (C/C5 option)?
Requires the C or C5 option. In the Communication Parameter Setting Group set Communication protocol to MODBUS RTU (or ASCII), then instrument number, speed, data bit/parity and stop bit; these are keypad-only.
Where is the official Shinko Technos PCA1 programmable controller (C/C5 option) Modbus documentation?
The source is Communication Instruction Manual PCA1 (C, C5) (No. PCA1CE3), revision 2019-12, published free by Shinko Technos at https://shinko-technos.co.jp/e/manual/english/PCA1CE3.pdf.
More Shinko Technos Modbus register maps
- Sensor (digital temperature controller)
Shinko Technos ACD-13A / ACR-13A / ACD-15A / ACR-15A digital indicating controller (C, C5 options)
Shinko ACD/ACR-13A (PID) and ACD/ACR-15A (valve positioning) with the C or C5 communication option; manual No.ACDR1CE8.
Also known as: ACD-13A, ACR-13A, ACD-15A, ACR-15A - Sensor (digital temperature controller)
Shinko Technos ACS-13A digital indicating controller (C5 option)
Shinko ACS-13A with the C5 serial communication option; communication manual No.ACS12CE5.
Also known as: ACS-13A-C5, ACS-13A C5 - Sensor (digital temperature controller)
Shinko Technos ACS2 digital indicating controller (C5, C5W options)
Shinko ACS2 with the C5 or C5W serial option, Shinko protocol / MODBUS RTU command set; manual No.ACS2CE3.
Also known as: ACS2-C5, ACS2-C5W - Sensor (conductivity controller)
Shinko Technos AER-102-ECH conductivity indicating controller (C5 option)
Shinko AER-102-ECH electrical conductivity controller with the C5 RS-485 option; manual No. AER11CECE5.
Also known as: AER-102-ECH - Sensor (digital temperature controller)
Shinko Technos BCS2 / BCR2 / BCD2 digital indicating controller (C5, C5W options)
Shinko BCx2 series (BCS2, BCR2, BCD2) with the C5 or C5W communication option, standard (not JC-allocated) command set; manual No.BCx2CE6.
Also known as: BCS2, BCR2, BCD2, BCx2 - Sensor (digital temperature controller)
Shinko Technos DCL-33A DC digital indicating controller (C5 option)
Shinko DCL-33A DC with the C5 option; communication manual No.DCL3CDCE2.
Also known as: DCL-33A DC, DCL-33A-DC-C5 - Sensor (digital temperature controller)
Shinko Technos DCL-33A digital indicating controller (C5 option)
Shinko DCL-33A with the C5 serial option, plain (non-block) Modbus protocol setting; manual No.DCL32CE3.
Also known as: DCL-33A-C5, DCL-33A C5 - Sensor (digital temperature controller)
Shinko Technos FC series digital indicating controller (C/C5 option, Modbus ASCII)
Shinko FCS-23A, FCR-13A, FCR-23A and FCD-13A with the C or C5 serial option; FCR-15A and FCD-15A have no Modbus (Shinko protocol only). Manual No.FC1CE11.
Also known as: FCS-23A, FCR-13A, FCR-23A, FCD-13A - Sensor (paperless recorder)
Shinko Technos GR200 paperless recorder (Modbus RTU / Modbus TCP)
Shinko GR200 paperless recorder with RS-485 Modbus RTU or Ethernet Modbus TCP; manual GR2CE1.
Also known as: GR200 - Sensor (chart recorder)
Shinko Technos HR-700 hybrid recorder (Modbus RTU, firmware 4.00+)
Shinko HR-700 hybrid recorders (multipoint and pen types), body version 4.00 or later, Modbus map version 01; manual No. HR7CE4.
Also known as: HR-700 - Sensor (digital temperature controller)
Shinko Technos JCL-33A digital indicating controller (C5 option)
Shinko JCL-33A with the C5 option, protocol set to plain 'Modbus RTU mode' or 'Modbus ASCII mode' (not the Block Read/Write modes, which use another layout); manual No.JCL3CE3.
Also known as: JCL-33A-C5, JCL-33A C5 - Sensor (digital temperature controller)
Shinko Technos JCS-33A / JCM-33A / JCR-33A / JCD-33A digital indicating controller (C5 option)
Shinko JCx-33A series (JCS, JCM, JCR, JCD-33A) with the C5 option; communication manual No.JC3CE11.
Also known as: JCS-33A, JCM-33A, JCR-33A, JCD-33A, JCx-33A - Sensor (digital temperature controller)
Shinko Technos JIR-301-M digital indicator (C5 option)
Shinko JIR-301-M with the C5 option, plain (non-block) Modbus protocol setting; manual No.JIR32CE4.
Also known as: JIR-301-M-C5, JIR-301-M C5 - Sensor (programmable temperature controller)
Shinko Technos PCB1 programmable controller (C5W/C5 option)
Shinko PCB1 programmable controllers with the C5W or C5 RS-485 option, native PCB1 command set; manual No. PCB1CE3.
Also known as: PCB1 - Sensor (digital temperature controller)
Shinko Technos PCD-33A programmable controller (C5 option)
Shinko PCD-33A program controller with the C5 RS-485 option; manual printed No.PCD3CE1 2003.02 (file PCD3CE2).
Also known as: PCD-33A-R/M, PCD-33A-S/M - Sensor (signal conditioner)
Shinko Technos SGxL signal conditioner series (Modbus RTU)
Shinko SGxL signal conditioners (SGBL, SGCL, SGDL, SGIL, SGLL, SGML, SGPL, SGRL, SGSL, SGTL, SGUL); SGFL and SGJL are not covered. Manual No.SGxL1CE3.
Also known as: SGBL, SGCL, SGDL, SGIL, SGLL, SGML, SGPL, SGRL, SGSL, SGTL, SGUL - Sensor (digital temperature controller)
Shinko Technos WCL-13A 2-channel digital indicating controller (C5 option)
Shinko WCL-13A two-loop controller with the C5 option; communication manual No.WCL1CE3.
Also known as: WCL-13A-C5, WCL-13A C5
Other temperature & process controllers register maps
- Sensor (digital indicating temperature controller)
Yokogawa UTAdvanced UT55A / UT52A digital indicating controller
Yokogawa UT55A and UT52A one- or two-loop controllers with RS-485 or Ethernet communication; D-register map from IM 05P07A01-01EN chapter 6 (UP55A program items excluded).
Also known as: UT55A, UT52A - Sensor (process / temperature controller)
Novus N20K48 modular process controller (Modbus RTU)
N20K48 controllers with the optional RS-485 interface, communication protocol V1.0x.
Also known as: Novus N20K48, N20K48 modular controller - Sensor (digital indicating temperature controller)
Yokogawa UTAdvanced UT35A / UT32A digital indicating controller
Yokogawa UT35A and UT32A single-loop controllers with RS-485 or Ethernet communication; D-register map from IM 05P07A01-01EN chapter 8 (UT32A-D loop 2 and UP35A/UP32A program items excluded).
Also known as: UT35A, UT32A, UT35A/MDL, UT32A/MDL - Sensor (digital temperature controller)
Fuji Electric PXR micro controller X (RS-485 Modbus option)
Fuji Electric PXR series controllers with the RS-485 Modbus communication option; manual INP-TN512642d-E.
Also known as: PXR3, PXR4, PXR5, PXR9 - Sensor (program temperature controller)
Yokogawa UTAdvanced UP55A program controller
Yokogawa UP55A program controller with RS-485 or Ethernet communication; D-register map from IM 05P07A01-01EN chapter 6 (UP55A column).
Also known as: UP55A - Sensor (digital process controller)
Fuji Electric PXH digital controller (Modbus RTU, monitoring map)
Fuji Electric PXH digital controllers on the RS-485 Modbus port; read-only monitoring registers from manual INP-TN514207c-E.
Also known as: PXH
All temperature & process controllers Modbus register maps →
Source: Communication Instruction Manual PCA1 (C, C5) · No. PCA1CE3 · rev. 2019-12. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.