Easy Modbus
  1. Home
  2. Modbus register maps
  3. Intesis (HMS Networks)
  4. INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)

VRF / split AC gateway · Modbus register map

Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) Modbus register map

Updated 19 November 2026

Short answer

Modbus server on the Samsung NASA R1/R2 bus covering indoor units, AHUs, ERVs, EHS / hydro units and chillers. Each configured unit gets a 100-register block; outdoor unit communication flags and all-unit commands sit at the bottom of the map. Modbus RTU and TCP run together.

This page lists 62 Modbus registers for the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) — 48 writable — with the table, 0-based wire address, data type, word order, scale, units and access of each, re-typed from Intesis (HMS Networks)’s own free documentation (linked below) and checked against it.

Manufacturer
Intesis (HMS Networks)
Model
INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)
Equipment type
VRF / split AC gateway
Registers
62 (48 writable)
Transport
Modbus RTU, Modbus TCP
Default unit ID
Not stated
TCP port
502
Documented addressing
0-based (the number printed is the address on the wire)
Also known as
INMBSSAM004O000, INMBSSAM008O000, INMBSSAM016O000, INMBSSAM064O000, SM-ACN-MBS-4, SM-ACN-MBS-8, SM-ACN-MBS-16, SM-ACN-MBS-64
Source document
Intesis Modbus Server - Samsung NASA User Manual · User Manual r1.4 EN · rev. 2020-12
Download CSV all columns JSON Manufacturer PDF ↗

Integration notes: Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)

Integration in brief

Add the units in Intesis MAPS with their unit type, send the project, then poll each Ui x 100 block. Write on/off, mode, fan and setpoint (tenths of °C).

Minimum registers to map

Addresses are 0-based wire addresses. Enough to monitor and run the unit; map more as the job needs.

RegisterNameTypeWhyAccess
HR 100On/offINT16On/offRead/write
HR 101Operation modeINT16ModeRead/write
HR 102Fan speedINT16Fan speedRead/write
HR 104Temperature setpointINT16Setpoint (x10)Read/write
HR 111Unit error codeINT16Error codeRead
HR 116Communication statusBITMAP16Communication status flagsRead
HR 0OU communication errorINT16Outdoor unit 0 communication errorRead

Enable Modbus control & writes

Units must be configured in MAPS; the NASA R1 (+) / R2 (-) bus goes to Port A A3/A4 with polarity.

Byte order & addressing

Network setup

Watch out for

Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) Modbus registers

Address = 0-based wire address (the documented number is shown under it when it differs) · Order: ABCD = high word first, CDAB = low word first · Scale: engineering value = raw × scale.

62 of 62 shown
Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) Modbus register map
TableAddressNameDescriptionTypeOrderScaleUnitsAccessValues / bits
HR0doc OUOU communication errorOutdoor unit address 0 shown; address = OU address 0..15.INT16Read0 = No error; 1 = Communication error
HR16OU addressing errorINT16Read0 = OU addressing OK; 1 = Manual addressing in OU required
HR20On (all units)INT16Write1 = Switch all on
HR21Off (all units)INT16Write1 = Switch all off
HR22Mode Auto (all units)INT16Write1 = Set Auto
HR23Mode Heat (all units)INT16Write1 = Set Heat
HR24Mode Dry (all units)INT16Write1 = Set Dry
HR25Mode Fan (all units)INT16Write1 = Set Fan
HR26Mode Cool (all units)INT16Write1 = Set Cool
HR27Mode Cool Storage (all units)INT16Write1 = Set Cool Storage
HR28Mode Heat Storage (all units)INT16Write1 = Set Heat Storage
HR29Fan speed Auto (all units)INT16Write1 = Set fan Auto
HR30Fan speed Low (all units)INT16Write1 = Set fan Low
HR31Fan speed Mid (all units)INT16Write1 = Set fan Mid
HR32Fan speed High (all units)INT16Write1 = Set fan High
HR33Swing on (all units)INT16Write1 = Set swing on
HR34Swing off (all units)INT16Write1 = Set swing off
HR35Temperature setpoint (all units)Tenths of a degree °C. Cool 18..30, Heat 16..30.INT16× 0.1°CWrite
HR36Ventilation on (all units)INT16Write1 = Set ventilation on
HR37Ventilation off (all units)INT16Write1 = Set ventilation off
HR38Hot water on (all units)INT16Write1 = Set hot water on
HR39Hot water off (all units)INT16Write1 = Set hot water off
HR100doc (Ui*100)+0On/offUnit index 1 shown; see notes.INT16Read/write0 = Off; 1 = On
HR101doc (Ui*100)+1Operation modeIU/AHU codes shown; HE, EHS/ERV+ and chiller use other codes (see notes).INT16Read/write0 = Auto; 1 = Heat; 2 = Dry; 3 = Fan; 4 = Cool
HR102doc (Ui*100)+2Fan speedINT16Read/write0 = Auto; 1 = Low; 2 = Mid; 3 = High
HR103doc (Ui*100)+3Vane swingINT16Read/write0 = Swing off; 1 = Swing on
HR104doc (Ui*100)+4Temperature setpointTenths of a degree °C. Cool 18..30, Heat 16..30.INT16× 0.1°CRead/write
HR106doc (Ui*100)+6Discharge setpoint cool (IU)Tenths of a degree °C; 8..18.INT16× 0.1°CRead/write
HR107doc (Ui*100)+7Discharge setpoint cool (AHU)Tenths of a degree °C; 8..25.INT16× 0.1°CRead/write
HR108doc (Ui*100)+8Discharge setpoint heat (IU)Tenths of a degree °C; 30..43.INT16× 0.1°CRead/write
HR109doc (Ui*100)+9Discharge setpoint heat (AHU)Tenths of a degree °C; 18..43.INT16× 0.1°CRead
HR110doc (Ui*100)+10Discharge current temperatureTenths of a degree °C.INT16× 0.1°CRead
HR111doc (Ui*100)+11Unit error code0 = no error, 100..999 = Samsung error code.INT16Read0 = No error
HR112doc (Ui*100)+12Slave chiller unit error code0 = no error, 100..999 = error code.INT16Read0 = No error
HR113doc (Ui*100)+13Slave chiller unit error flagsBit n set = error in slave chiller unit n (0..15).BITMAP16Readbit 0 = Error in slave unit 0; bit 1 = Error in slave unit 1; bit 2 = Error in slave unit 2; bit 3 = Error in slave unit 3; bit 4 = Error in slave unit 4; bit 5 = Error in slave unit 5; bit 6 = Error in slave unit 6; bit 7 = Error in slave unit 7; bit 8 = Error in slave unit 8; bit 9 = Error in slave unit 9; bit 10 = Error in slave unit 10; bit 11 = Error in slave unit 11; bit 12 = Error in slave unit 12; bit 13 = Error in slave unit 13; bit 14 = Error in slave unit 14; bit 15 = Error in slave unit 15
HR114doc (Ui*100)+14Filter alarmINT16Read0 = Normal; 1 = Alarm
HR115doc (Ui*100)+15Filter alarm resetINT16Write1 = Reset
HR116doc (Ui*100)+16Communication statusBITMAP16Readbit 0 = Exists; bit 1 = Ready; bit 2 = Data updated; bit 3 = Type OK
HR117doc (Ui*100)+17Remote control disablementINT16Read/write0 = Not disabled; 1 = Disabled
HR118doc (Ui*100)+18Buzzer sound onINT16Write1 = Set buzzer on
HR119doc (Ui*100)+19Buzzer sound offINT16Write1 = Set buzzer off
HR120doc (Ui*100)+20Unit typeINT16Read0 = Not defined; 1 = IU; 2 = HE; 3 = HT; 4 = AHU; 5 = ERV; 6 = ERV+; 7 = EHS; 8 = Master chiller
HR121doc (Ui*100)+21Hot water on/offINT16Read/write0 = Off; 1 = On
HR122doc (Ui*100)+22Hot water mode HE/HTINT16Read/write0 = Eco; 1 = Standby; 2 = Power
HR123doc (Ui*100)+23Hot water mode EHSINT16Read/write0 = Eco; 1 = Standby; 2 = Power; 3 = Force
HR124doc (Ui*100)+24Hot water setpoint HETenths of a degree °C; 30..75.INT16× 0.1°CRead/write
HR125doc (Ui*100)+25Hot water setpoint HTTenths of a degree °C; 30..75.INT16× 0.1°CRead/write
HR126doc (Ui*100)+26Hot water setpoint EHSTenths of a degree °C; 30..70.INT16× 0.1°CRead/write
HR127doc (Ui*100)+27Hot water current temperatureTenths of a degree °C.INT16× 0.1°CRead
HR128doc (Ui*100)+28Water in temperatureTenths of a degree °C.INT16× 0.1°CRead
HR129doc (Ui*100)+29Water out temperatureTenths of a degree °C.INT16× 0.1°CRead
HR130doc (Ui*100)+30Water out setpoint HETenths of a degree °C. Cool 5..25, Heat 15..50.INT16× 0.1°CRead/write
HR131doc (Ui*100)+31Water out setpoint HTTenths of a degree °C; 25..80.INT16× 0.1°CRead/write
HR132doc (Ui*100)+32Water out setpoint EHSTenths of a degree °C. Cool 5..25, Heat 15..55.INT16× 0.1°CRead/write
HR133doc (Ui*100)+33Water out setpoint chillerTenths of a degree °C. Cool 5..25, Heat 15..55.INT16× 0.1°CRead/write
HR134doc (Ui*100)+34Water out average temperatureTenths of a degree °C.INT16× 0.1°CRead
HR135doc (Ui*100)+35Ventilation on/offINT16Read/write0 = Off; 1 = On
HR136doc (Ui*100)+36Ventilation operating modeINT16Read/write0 = Bypass; 1 = Heat exchange; 2 = Sleep; 3 = Auto
HR137doc (Ui*100)+37Ventilation fan speedINT16Read/write0 = Low; 1 = High; 2 = Turbo
HR138doc (Ui*100)+38WindFreeINT16Read/write0 = Disable; 1 = Enable
HR139doc (Ui*100)+39Air cleanINT16Read/write0 = Disable; 1 = Enable
HR140doc (Ui*100)+40360 CST air flow directionINT16Read/write1 = Pos 1; 2 = Pos 2; 3 = Pos 3; 10 = Swing

Notes on this map

Check it against the live device. A register map tells you what the controller can expose; the unit in front of you may differ by firmware or options. Read a few registers and compare them with the unit’s own display; for a 32-bit value the float and byte-order decoder shows all four word orders at once, so a wrong word order or scale is obvious. New to this? Read what a register map is and why addresses are off by one.

Questions about the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)

What Modbus registers does the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) have?

This map lists 62 registers: 62 holding registers. 48 of them can be written. Registers vary with firmware, options and configuration, so confirm against the device.

Are the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) Modbus addresses 0-based or 1-based?

The manufacturer's document numbers registers 0-based (the number printed is the address on the wire). Every address on this page is the 0-based wire address you put in the request; the documented number is shown under it where it differs. The manual states formula results are link-layer addresses with the first register at 0. Unit index Ui (1..64, from the MAPS Units Configuration tab) uses Ui x 100 + offset; outdoor unit address OU (0..15) is its own register 0..15. This file lists Ui = 1 (100..140) and OU 0.

What are the minimum Modbus registers to integrate the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)?

Start with HR 100 On/off (On/off); HR 101 Operation mode (Mode); HR 102 Fan speed (Fan speed); HR 104 Temperature setpoint (Setpoint (x10)); HR 111 Unit error code (Error code); HR 116 Communication status (Communication status flags); HR 0 OU communication error (Outdoor unit 0 communication error).

How do I enable Modbus control of the Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units)?

Units must be configured in MAPS; the NASA R1 (+) / R2 (-) bus goes to Port A A3/A4 with polarity.

Where is the official Intesis (HMS Networks) INMBSSAM016O000 Samsung NASA (R1/R2) VRF to Modbus gateway (4 to 64 units) Modbus documentation?

The source is Intesis Modbus Server - Samsung NASA User Manual (User Manual r1.4 EN), revision 2020-12, published free by Intesis (HMS Networks) at https://www.hms-networks.com/docs/default-source/products/intesis/manuals-and-guides---manuals/user-manual-inmbssamxxxo000.pdf.

More Intesis (HMS Networks) Modbus register maps

Other ac & vrf gateways register maps

All ac & vrf gateways Modbus register maps →

Source: Intesis Modbus Server - Samsung NASA User Manual · User Manual r1.4 EN · rev. 2020-12. Register numbers, types, scaling and units are reproduced as published; descriptions are our own.